Zenoah Komatsu G3300 Owner's Manual
  1. Manuals
  2. Brands
  3. Zenoah Manuals
  4. Chainsaw
  5. G3300
  6. Owner's manual

Zenoah Komatsu G3300 Owner's Manual

Hide thumbs Also See for Komatsu G3300:
Table of Contents

Advertisement

Quick Links

See also: Owner's Manual
CHAINSAWS
G3300EZ
OWNER'S MANUAL
G3300
G3300 / G3300EZ
848C3593A1 (411)
G
G
B
B
GB-1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Komatsu G3300 and is the answer not in the manual?

Questions and answers

Related Manuals for Zenoah Komatsu G3300

Summary of Contents for Zenoah Komatsu G3300

  • Page 1 G3300 / G3300EZ 848C3593A1 (411) OWNER’S MANUAL CHAINSAWS G3300 G3300EZ GB-1...
  • Page 2 G3300 / G3300EZ EXPLANATION OF SYMBOLS AND SAFETY WARNINGS Read operator's instruction Wear head, eye and ear book before operating this protection. machine. Use the chain saw Warning! Danger of with two hands. kickback. Read, understand and follow all warnings. WARNING!!! RISK OF DAMAGING HEARING IN NORMAL CONDITIONS OF USE, THIS MACHINE...

  • Page 3: Table Of Contents

    : G3300 G3300EZ Serial no. : 000101 and up Make : KOMATSU ZENOAH CONFORMS TO THE REQUIRMENTS OF THE MODIFIED MACHINES DIRECTIVE (Directive 98/37/EC) AND TO THE NATIONAL REGULATIONS GOVERNING ITS TRANSPOSITION ABROAD : AND THAT IT HAS BEEN ISSUED WITH A “CE”CERTIFICATE, NO. M.0303.04.3211 (G3300), M.0303.04.3212 (G3300EZ) BY THE ISTITUTO CERTIFICAZIONE...

  • Page 4: For Safe Operation

    G3300 / G3300EZ 1. For safe operation 1. Never operate a chain saw when 9. Never start cutting until you have you are fatigued, ill, or upset, or a clear work area, secure foot- under the influence of medica- ing, and a planned retreat path tion that may make you drowsy, from the falling tree.
  • Page 5 G3300 / G3300EZ move the clutch, structural dam- saw chain in the cut. Tip contact age to the flywheel could occur in some cases may cause a light- which could subsequently cause ning fast reverse reaction,kicking the flywheel to disintegrate.) the guide bar up and back to- 16.

  • Page 6: Explanation Of Symbols On The Machine

    G3300 / G3300EZ 2. Explanation of Symbols on the Machine For safe operation and maintenance, symbols are carved in relief on the machine. According to these indications, please be careful not to make any mistake. The port to refuel “MIX GASOLINE” The screw under the “H”...
  • Page 7 G3300 / G3300EZ While temporary tightening, you may hear the “click” sound. But do not stop tightening at that time. This sound does not mean that the saw chain and guide bar were assembled. (1) Tensioner screw (2) Loosen 5. While holding the chain cover, temporary tighten the (3) Tighten nut assembly and fix the bar and chain cover.

  • Page 8: Fuel And Chain Oil

    2. Put fuel into the fuel tank to 80% of the full capacity. 3. Fasten the fuel cap securely and wipe up any fuel spillage around the unit. • The Komatsu Zenoah engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use. If Komatsu Zenoah oil is not available, 1.

  • Page 9: Operating The Engine

    G3300 / G3300EZ 5. Operating the Engine It is very dangerous to run a chainsaw that mounts broken parts or lacks any parts. Before starting engine, make sure that all the parts including bar and chain are installed properly. STARTING THE ENGINE 1.
  • Page 10 G3300 / G3300EZ The carburetor on your unit has been factory adjusted, but may require fine tuning due to a change in operat- ing conditions. Before adjusting the carburetor, make sure that the pro- vided air/fuel filters are clean and fresh and the fuel prop- erly mixed.

  • Page 11: Sawing

    G3300 / G3300EZ 6. Sawing gine at full speed. If the chain is slow • Before proceeding to your job, to stop or does not stop, replace the read the section “For Safe brake band and clutch drum before Operation”. It is recommended use.

  • Page 12: Maintenance

    G3300 / G3300EZ A log lying on the ground First check to which side the limb is bent. Then make the initial cut from the bent side and finish by sawing from the opposite side. Be alert to the springing back of a cut limb. Saw down halfway, then roll the log over and cut from Pruning of Standing Tree the opposite side.
  • Page 13 G3300 / G3300EZ PERIODICAL SERVICE POINTS 2. Fuel filter (Every 25 hours use) Using a wire hook, take out the filter from the filler port. Clean away the dirt attached to the filter. Replace with a 1. Air cleaner new one if needed. 1.

  • Page 14: Maintenance Of Saw Chain And Guide Bar

    Chain tilts and file it to the proper level as illustrated. WARNING: This saw is equipped with one of the following low kickback bar/chain combinations: Appropriate gauge checker Komatsu Zenoah Part Number Saw Model Bar Size Guide Bar Saw Chain G3300/G3300EZ...

  • Page 15: Troubleshooting Guide

    G3300 / G3300EZ 9. Troubleshooting Guide Case 1. Starting failure Case 3. Oil does not come out Check oil for sub- Make sure the icing prevention system is not Replace. standard quality. working. Check fuel for water Replace with proper Check oil passage or substandard mix- fuel.

  • Page 16: Specifications

    OF THE COMPANY. riod, the failed part will be replaced or repaired free of charge by a KOMATSU ZENOAH authorized dealer. THE COMPANY IS LIABLE FOR DAMAGES TO OTHER ENGINE COMPONENTS CAUSED BY THE FAIRURE OF WARRANTY PERIOD: 1 year (6 months if used profes- A WARRANTED PARTS STILL UNDER WARRANTY.

This manual is also suitable for:

Komatsu g3300ez

Table of Contents

Save PDF