ParaBody 807 BODYSYSTEM User Manual
  1. Manuals
  2. Brands
  3. ParaBody Manuals
  4. Home Gym
  5. 807 BODYSYSTEM
  6. User manual
ParaBody 807 BODYSYSTEM User Manual

ParaBody 807 BODYSYSTEM User Manual

Workout center
Hide thumbs Also See for 807 BODYSYSTEM:
Table of Contents

Advertisement

Quick Links

807 BODYSYSTEM
WORKOUT CENTER
WARNING:
Read and follow all directions
for each step to insure proper
assembly of this product.
CLASS H
PART # 7052601
REV. B
USER'S GUIDE
1
Version: 807107
Revision: 07/09/01

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 807 BODYSYSTEM and is the answer not in the manual?

Questions and answers

Related Manuals for ParaBody 807 BODYSYSTEM

Summary of Contents for ParaBody 807 BODYSYSTEM

  • Page 1 807 BODYSYSTEM WORKOUT CENTER WARNING: Read and follow all directions for each step to insure proper assembly of this product. USER’S GUIDE CLASS H PART # 7052601 REV. B Version: 807107 Revision: 07/09/01...

  • Page 2: Important Safety Information

    Use only the pin provided by the manufacturer. If unsure, call your authorized ParaBody dealer. NOTE: In a continual effort to improve our products, specifications are subject to change 2001 Life Fitness, a division of Brunswick Corporation. All rights reserved. © ParaBody is a trademark of Brunswick Corporation www.parabody.com...

  • Page 3: Important Notes

    Please note: * Thank you for purchasing the ParaBody 807 Gym System. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function. * This product must be assembled on a flat, level surface to assure its proper function. DO NOT securely tighten any frame connections until the entire frame has been assembled, unless otherwise stated.
  • Page 4 4’ 6’ 1’ 2’ 3’ 5’ 7’ 1’ 2’ 3’ 4’ 5’ 1 Square = 1’ X 1’...
  • Page 5 PART # 7058908 6407508 6111002 HEIGHT ADJUSTMENT BAR 6406602 6407802 6407302 6407202 6024702 6406401 6406501 6125101 6194601 6654521 6654121 3102909 3102922 3102904 3102910 3102501 3102601 3102802 3102502 6236701 3102804 1/2” LOW HEIGHT LOCK NUT 6412001 3/8” SPRING PIN ASSEMBLY 6020601 3105401 3109602 6145801...
  • Page 6 FIGURE 1 STEP 1: • Attach eight PARAGLIDE STRIPS (31) to the WOLFF SLEEVE (4) (FOUR ON EACH END) as shown in FIGURE 1 using the following steps: • Thoroughly clean all surfaces where the PARAGLIDE STRIPS are to be attached. •...
  • Page 7 FIGURE 2 STEP 2: • Pull back the SPRING PIN on the WOLFF SLEEVE (4) and slide it over the end of the BENCH FRAME (2) as shown in FIGURE 2. Engage the SPRING PIN into one of the adjustment holes. •...
  • Page 8 FIGURE 3 STEP 3: • Insert four 2” SQ. END CAPS (33) into the BASE TUBES of the UPRIGHT FRAME (1) as shown in FIGURE 3. • SECURELY assemble the BENCH FRAME (2) to the UPRIGHT FRAME (1) using two 3/8 X 3” BOLTS (17), one 3/8 X 2-3/ 4”...
  • Page 9 FIGURE 4 STEP 4: • Attach eight PARAGLIDE STRIPS (31) to both UPRIGHT TUBES on the UPRIGHT FRAME (1) (FOUR ON EACH END) as shown in FIGURE 4 using the following steps: • Thoroughly clean all surfaces where the PARAGLIDE STRIPS are to be attached. •...
  • Page 10 FIGURE 5 STEP 5: • To assemble the SEAT PAD (13) to the WOLFF SLEEVE (4), start by sliding two HINGE TABS (9) over the PIN of the WOLFF SLEEVE (ONE ON EACH SIDE) as shown in FIGURE 5, and SECURELY assemble each HINGE TAB (9) to the SEAT PAD (13) using two 3/8 X 1”...
  • Page 11 FIGURE 6 STEP 6: • To assemble the BACK PAD (14) to the WOLFF SLEEVE (4), slide the two remaining HINGE TABS (9) over the PIN of the WOLFF SLEEVE (ONE ON EACH SIDE) as shown in FIGURE 6, and SECURELY assemble each HINGE TAB (9) to the BACK PAD (14) using two 3/8 X 1”...
  • Page 12 FIGURE 7 STEP 7: • Insert one 1-3/4” SQ. END CAP (23) into the top of the LEG EXTENSION NECK (7) as shown in FIGURE 7. • Slide two ROLLER PADS (12) over each end of the SHAFT of the LEG EXTENSION NECK (7), as shown in FIGURE 7, and secure in place using two 3/4”...
  • Page 13 LOW HEIGHT 24 STEP 8: • Insert three 1-3/4” SQ. END CAPS (23) into the ends of the LEG EXTENSION (8) as shown in FIGURE 8. • Insert two 1/2” FLANGE BEARINGS (26) into the BUSHING on the LEG EXTENSION (8) as shown in FIGURE 8. •...
  • Page 14 FIGURE 9 STEP 9: • When ready to perform LEG CURLS or LEG EXTENSION, pull up slowly on the front of the BENCH FRAME (2) and allow the U-PIN (10) to rest on top of the TAB of the BASE LEG (5). (NOTE: THE BENCH FRAME MUST BE ADJUSTED UP WHEN USING THE LEG EXTENSION TO ALLOW PROPER CLEARANCE FOR WEIGHT PLATES)
  • Page 15 FIGURE 10 STEP 10: • Set the HEIGHT ADJUSTMENT BAR (3) across the UPRIGHT FRAME (1) as shown in FIGURE 10, for performing INCLINE, or MILITARY PRESSES. When performing DIPS, use the HEIGHT ADJUSTMENT BAR (3) to hold the BACK PAD forward as shown in the WORKOUT MANUAL.

  • Page 16: Maintenance

    YOU MAY NEED SERVICE YOU WILL BE ASKED FOR THIS INFORMATION. REMEMBER TO FILL OUT YOUR WARRANTY REGISTRATION CARD AND MAIL BACK. MODEL #________________________ SERIAL #_________________________ DATE OF PURCHASE: _____________ DEALERS NAME: _________________ DEALERS PHONE #_______________ Thank you for purchasing the ParaBody 807 Gym System. MAINTENANCE...

  • Page 17: Limited Warranty

    ParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The Warranty terms apply to IN HOME USE ONLY. 1. LIMITED WARRANTY ON FRAME AND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repaired or replaced by ParaBody.
  • Page 18 Life Fitness Italia S.R.L. Via Elvas 92 39042 Bressanone Italy Phone: 39 (472) 835-470 Fax: 39 (472) 833-150 Life Fitness Asia Pacific Limited Room 2610, Miramar Tower 132 Nathan Road, Tsimshatsui Kowloon, Hong Kong Phone: (852) 2891-6677 Fax: (852) 2575-6001 www.parabody.com...

Table of Contents