Advertisement
Advertisement
Table of Contents
Related Manuals for Harbinger LP9800
Summary of Contents for Harbinger LP9800
- Page 1 HIGH LP9800 POWERED MIXER...
-
Page 2: Welcome
Thank you for your purchase of this Harbinger® Powered Mixer. It’s packed with quality features usually found only on larger, more expensive systems. To get the most from your new LP9800, take a moment and read through this entire manual to learn about all its important features. -
Page 3: Important Safety Instructions
LP9800 POWERED MIXER IMPORTANT SAFETY INSTRUCTIONS DANGER IMPORTANT SAFETY INSTRUCTIONS 1. Read all safety and operating instructions before using Exposure to extremely high noise levels may cause this product. permanent hearing loss. Individuals vary considerably 2. All safety and operating instructions should be kept for to noise-induced hearing loss but most will lose some future reference. -
Page 4: Table Of Contents
BASIC OPERATION • Ensure the LP9800’s AC power switch is turned off. • Place the LP9800 on the floor, a table, or a sturdy stand. • Turn down all Level, Monitor Level, and Main Level Controls. • Plug speakers into the rear panel speaker jacks. -
Page 5: Front And Rear Panel Diagrams
LP9800 POWERED MIXER FRONT AND REAR PANEL DIAGRAMS HIGH www.HarbingerProAudio.com... -
Page 6: Front Panel
This is the bass control used to boost or cut low frequencies on the input channel using a low shelf filter with +/- 15dB of boost or cut, below 60Hz. Useful for removing rumble on vocal or acoustic guitar inputs. LP9800 Owner's Manual... - Page 7 MAIN output. Phantom On/Off This button is used when condenser microphones are connected to the LP9800, providing +48V to the XLR microphone inputs. Phantom power only applies to XLR input connections. CD/AUX/LINE IN Unbalanced inputs for CD/MP3 players.
- Page 8 Amplifiers Assign Switch MAIN L+R – MONITOR • Dual Mono Mode The LP9800 features 225W@8Ω, 350W4Ω • Output 1 is Main or 800W@8Ω Mono Bridged • Output 2 is Monitor • 4Ω minimum speaker load per output MAIN L –...
- Page 9 LP9800 POWERED MIXER FRONT PANEL Monitor & Main 9-Band Graphic EQ Graphic Equalizer contains 9 filters that each cut or boost +/- 12dB around their center frequency. These filters can be used to contour the overall sound of all inputs, and reduce feedback (cut only). LED per EQ band. Press EQ...
- Page 10 Decay Time: 50ms Hall 2 Decay Time: 80ms Delay 1 Delay Time: 100mS Delay 2 Delay Time: 300mS Flanger Decay Time: 50mS Chorus Rate: 44.1K Chorus/Room1 Rate: 22K Chorus/Room2 Rate: 44.1K Vocal Cancel Rotary Speaker Modulation Depth: 6dB LP9800 Owner's Manual...
-
Page 11: Rear Panel
This is the AC Mains connection. Use only the supplied IEC cable or a UL listed replacement IEC Cable and 100-120V/220-240V/50/60Hz switching power supply. On Off Switch This switch turns on the LP9800 and off. When powered on the blue power led will light. Speaker Outputs L/Monitor Connect up to two (2) loudspeakers to the speaker output jacks. -
Page 12: Specifications
Type of Effects AL3201 Presets Controls encoder Main Mix Section Noise (Bus noise) ≤0.5mV Monitor Max Out +21dBu FX Sends Max Out +21dBu Total Harmonic Distortion 1% Signal to Noise Ratio 90dB Static Power Consumption Power Source 115V-50/60Hz 230V-50Hz LP9800 Owner's Manual... -
Page 13: Power Amplifier Diagram
LP9800 POWERED MIXER POWER AMPLIFIER DIAGRAM www.HarbingerProAudio.com... -
Page 14: Output Block Diagram
LP9800 POWERED MIXER OUTPUT BLOCK DIAGRAM LP9800 Owner's Manual... - Page 15 LP9800 POWERED MIXER NOTES www.HarbingerProAudio.com...
-
Page 16: Warranty
(2) year warranty period. Some Harbinger provides, to the original purchaser, a two (2) year limited states do not allow limitation on how long an implied warranty lasts, so the warranty on materials and workmanship on all Harbinger cabinets, above limitation may not apply to you.
Need help?
Do you have a question about the LP9800 and is the answer not in the manual?
Questions and answers