Life fitness dual adjustable pulley owner's manual (14 pages)
Summary of Contents for Life Fitness FIT 1.0 CM
Page 1
FIT 1.0 CM GYM SYSTEM USER GUIDE WARNING: Read and follow all directions for each step to insure proper assembly of this product. CLASS -S PART # 7946001 REV. A VERSION: FSFCM1-0102-001 DATE: 06-13-05...
Life Fitness dealer. Please note: * Thank you for purchasing the Life Fitness Fit 1.0 CM Gym System. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function.
A DJUSTA BLE HA NDLE FOOT STRA P GUIDE CA BLE UPPER CA BLE (SHORT) LOWER CA BLE (LONG) USER GUIDE WEIGHT PLA TE LA BELS 1-26 PLA CA RD, FIT 1.0 CM UPPER EXEC. PLA CA RD, FIT 1.0 CM LOWER EXEC.
SECURLEY TIGHTEN 3/8 x 3/4 3/8 x 1” STEP 1: LOOSELY assemble bottom of the LEFT UPRIGHT (4) and RIGHT UPRIGHT (5) to FRONT UPRIGHT (1) using four 3/8 x 3-1/2 BOLTS (34), eight 3/8 WASHERS (28) and four 3/8 NUTS (33) and TOP PULLEYS (7) LOOSELY assemble the top of the LEFT UPRIGHT (4) and RIGHT UPRIGHT (5) to FRONT UPRIGHT (1) and TOP PULLEYS (7), using four 3/8 x 1”...
Page 8
DO NOT TIGHTEN LOWER FRAME COMPONENTS UNTIL TOP COVERS ARE INSTALLED 6-20 x 1/2 10-32 x 3/8 3/8 x 3/4 STEP 2: LOOSELY attach BASE PLATFORM (2) to front of FRONT UPRIGHT (1) using two 3/8 x 3/4” BOLTS (31), and two 3/8 WASHERS (28).
Page 9
BEFORE PROCEEDING TO STEP THREE, REFER TO SHROUD KIT ASSEMBLY INSTRUCTIONS. FRONT SHROUD AND BRACKETS WILL NEED TO BE INSTALLED AS PART OF STEP THREE...
Page 10
NOTE: REFER TO SHROUD KIT PRIOR TO STARTING STEP 3. FRONT SHROUD AND BRACKETS MUST BE INSTALLED FIGURE 3 STEP 3: Insert two GUIDE ROD BUSHINGS (30) into bottom of FRONT UPRIGHT (1), slide one CUSHION (24) to bottom of each GUIDE ROD (22) and insert both GUIDE RODS (22) thru GUIDE ROD BUSHINGS (30) and holes located at bottom of FRONT UPRIGHT (1) CAREFULLY slide HEAD PLATE (12) over top of GUIDE RODS (22) followed by two HEAD PLATE BUMPERS (36),...
Page 11
NOTE: SHROUDS HAVE BEEN REMOVED FOR ILLUSTRATIONAL PURPOSES ONLY MUST DISASSEMBLE ONE END OF CABLE AND REASSEMBLE AFTER ROUTING (SEE FIG 7 PAGE 14) STEP 4 NOTE: IF THE 50# ADD ON KIT WAS PURCHASED, USE THE CABLE FROM THAT KIT AND REFER TO KIT ASSEMBLY INSTRUCTION FOR HEAD PLATE ASSEMBLY Dimension between bottom of PULLEY BRACKET and top of JAM NUT approximately 1 inch.
Page 12
FIGURE 5 STEP 5: Insert ball end of GUIDE CABLE 7746001 (42) through eye hook on FLOATING PULLEY BRACKET (11), insert and hook ball end of cable into slotted bushing located at the bottom of frame. Screw threaded end of cable into the FRONT UPRIGHT (1) and loosely tighten cable by screwing JAM NUT to top of FRAME REPEAT ABOVE PROCESS FOR OTHER GUIDE CABLE (42)
Page 13
MUST DISASSEMBLE ONE END OF CABLE AND REASSEMBLY AFTER ROUTING (SEE FIG 7 PAGE 14) STEP 6: Insert ball end of LONG CABLE 7745401 (44) under pulley #1 and thru slot in BASE PLATFORM (2). Run cable underneath and up the back side of pulley #2. Then run cable up and around the front and down the back side of pulley #3.
Page 14
STEP 7: USE THIS ASSEMBLY AT THE END OF EACH CABLE Slide each item onto cable as follows: ITEM 1, ITEM 2, ITEM 3, and insert cable end into ITEM 4. Slide entire assembly over ITEM 4 and secure by screwing ITEM 5 into ITEM 4 and TIGTHEN SECURELY QUICK CONNECT ASSEMBLY - PART NUMBER 7872601 ITEM QTY.
Page 15
3/8 x 2-1/2 10-32 x 3/8 FIGURE 8 STEP 8 Attach FRONT SHROUD (8) using two 3/8 X 2-1/2 SCREWS (35) and two 3/8 WASHERS (28) Attach REAR BOTTOM PLATE (13) using two 10-32 X 1/2 SCREWS (25) SECURELY TIGTHEN CABLE GUIDES (REFER TO FIG 5, PAGE 11)
Page 16
STEP 9: Pre-assemble two FLANGE BEARINGS (23) and SHAFT (32) into ADJUSTMENT HUB as illustrated Attach ROLLER PAD ASSEMBLY (3) to center hole ADJUSTMENT HUB using two 3/8 WASHERS (28) and two 3/8 X 3/4 BOLTS (31) and tighten SECURELY. 3/8 x 3/4 PIN MUST BE LOCATED ON...
Page 17
!! DO NOT OVERTIGHTEN SCREWS INSTALL SCREW (25) BEFORE SCREWS (26) STEP 10: Attach TOP COVER (15) using four METAL SCREWS (25) Attach FRONT and BACK MID COVERS (18), (19) to each other using four PLASTIC SCREWS (26) as shown in illustration. Attach BACK MID COVER to FRONT UPRIGHT (1) using two METAL SCREWS (25) Finally align and stick MEDALLION (20) to front of MID COVER (19) as shown.
Page 18
STEP 11: Lift HEAD PLATE ASSEMBLY and insert 15 or 20 W EIGHT PLATES (46). Apply W EIGHT STACK LABELS (47) starting with “1” on the HEAD PLATE and descending down. REFER TO SHROUD ASSEM BLY GUIDE TO ASSEM BLY REAR SHROUD Referencing step 7, push back on ITEM (3) at end of cable and attach SHORTER HANDLES (38) to top of frame Repeat process for attaching the ADJUSTABLE HANDLES (40 ) to the lower cable ends and the medium handles (39) to the middle ends.
Please note: * We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water. Touch-up paint can be purchased from your Life Fitness customer service representative at (800) 328-9714.(Outside of the U.S. and Canada, +1-847-288-3300) * Inspect equipment daily.
• Lube the Guide Rods. Apply the lubricant to a cotton cloth, then run the cotton cloth up and down the guide rods as needed. Do not spray lubricant directly on the Guide Rods. Thank you for purchasing the LifeFitness FIT 1.0 CM . If unsure of proper use of equipment, call your local LifeFitness distributor or call the LifeFitness customer service department at...
Life Fitness extends the following LIMITED WARRANTY to the original owner (proof of purchase required, keep your receipt with this manual) of the Life Fitness product. The Warranty terms apply to IN HOME and LIGHT INSTITUTIONAL USE ONLY. 1. LIMITED WARRANTY ON FRAME AND WELDS. If the frame of the Life Fitness product or a weld should crack or break, it will be repaired or replaced by Life Fitness at its option.
Need help?
Do you have a question about the FIT 1.0 CM and is the answer not in the manual?
Questions and answers