Convergent BULLET HP Quick Start Manual

BULLET HP
QUICK START GUIDE
MADE IN THE
This product requires the use of a
mobile app to properly perform.
Visit ConvergentHunting.com
for a link or scan the code at right.
ConvergentHunting.com
Deploy THE CALL
1
First, let's open the call to reveal its speakers and
controls. To do this, twist the top area of the call about a
1/8 of a turn counter-clockwise, in much the same way
you would unscrew and open the lid on a jar. Then pull
upward to open the call. Once opened, turn approxi-
mately 1/8 of a turn clockwise to lock it into the open, or
"deployed" position.
This will reveal the speakers on one
side, and the ground stake/decoy storage and
controls on the other.
HELPFUL TIP:
DOWNLOAD
THE APP!
As you are sliding the speaker portion out, rotate the
caller to where the storage cavity is facing upwards/
speaker facing down. This ensures that the stake and
decoy remain in the cavity and are easy to access.
If this cavity is facing downward the stake and decoy
could fall out. Once you do this a few times it will
become natural.
POweriNG ON
3
With the call still in the open, or "deployed" position, push the power button and you
should see the Bluetooth light start to blink. It will be solid when paired with a device.
The call is now on. Press the power button again to turn the unit off.
The Bullet HP has an internal, high-capacity lithium-ion battery pack that provide over
10 hours of continuous run time. This means you will never have buy batteries and
you can concentrate on the hunt - and hunt all day without the worry of replacing
depleted batteries or having to recharging mid-hunt.
LOW BATTERY WARNING!
As the battery on the Bullet HP becomes low, the power light will flash (red) to let
you know that the battery is starting to get low. When the battery level flashes, you
have approximately 20% of your battery life left.
BHP-4000-QSG-01
CHARGE THE CALL
2
There is a USB cable and wall charger included
with the call. Please check your product box for
this cable and insert one end into the calls' USB
port, marked in the image at right. The power
light should come on & be bright orange.
You can charge by plugging the other end of the
cable into the supplied AC wall charger or your
vechicle's USB port, or a USB port on your
computer.
The power light is orange during charging, and
when it's fully charged, it will turn solid GREEN.
(No power light shows when in use.)
PLEAse NOTE!
Wall charge takes approximately 4 hrs
for a full charge.Charging using USB
from another device or vehicle can take
approximately 9 hours to fully charge.
BLUETOOTH PAIRING
4
Grab your mobile device (iOS or Android) and open to your Bluetooth settings. Make
sure Bluetooth is turned "on".
Push and hold the bluetooth button on the Bullet HP for 3-4 seconds and release.
The blue Bluetooth light will start flashing. After a few seconds, you should see
"Bullet 0.07" appear (on your mobile device) in your list of available devices to which
you can connect. The light will be solid blue when successfully paired with a device.
Follow your devices prompts to connect to the Bullet HP (Bullet 0.07) and you should
see the status on your mobile device show "connected" and the Bluetooth light on the
Bullet HP should be a solid blue color to indicate that you have successfully paired.
If there is a problem with connecting to the call, turn Bluetooth off on your mobile
device and repeat the steps above to pair with Bullet HP
NOTE: When the device is looking for a new pairing (after pressing pairing button),
blue LED flashes rapidly, whereas when the device is looking to re-establish an
existing pairing, it is a slow blink.
In some instances, if your device is having trouble pairing, Bluetooth memory needs
to be "erased" so that it will "forget" all past paired devices. This can be done by
pressing (and holding) the Bluetooth button on the Bullet HP for 10 seconds.
.
USB Port