Related Manuals for Danfoss 3060
Summary of Contents for Danfoss 3060
- Page 1 3060 electro-mechanical programmer for controlling heating & hot water Installation & User Instructions This product complies with the following EC Directives: Electro-Magnetic Compatibility Directive. (EMC) (2004/108/EC) Low Voltage Directive. (LVD) (2006/95/EC)
-
Page 2: Table Of Contents
Index Installation Product specification Installation Wiring User Your programmer Programming the unit Setting the clock Using the programmer Contact details... -
Page 3: Product Specification
Installation Instructions Please Note: This product should only be installed by a qualified electrician or competent heating installer, and should be in accordance with the current edition of the IEEE wiring regulations. Product specification Specification Power supply 230 ± 15% Vac, 50/60Hz Switch action 2 x SPST, type 1B Switch rating Max 264 Vac, 50/60Hz, 3(1) A Timing accuracy... -
Page 4: Installation
2. Slacken two screws securing plug-in module to backplate and separate module from backplate by pulling upwards. 3. Fix backplate to wall (3 hole fixing). 4. Referring to wiring diagrams below and opposite make electrical connections as shown (as applicable). The diagrams indicate that terminals 3 and 5 are not internally connected to the programmer and may therefore be used as spare wiring terminals if required. 5. Ease of installation can be achieved by the use of the Danfoss Randall Wiring Centre which is obtainable from most Builders Merchants and Distributors. NOTE: If a Wiring Centre is used follow the installation instructions included with that unit and not the following wiring diagrams. 6. Secure cable cores under cable clamp. -
Page 5: Wiring
Wiring WIRING - FULLY PUMPED SYSTEM 3060 Terminals Mains WIRING - FULLY PUMPED SYSTEM Supply 3060 Terminals Danfoss Randall Danfoss Mains ATC Cylinder Stat Randall Supply RMT230 Room Stat 2 core + 3 core 3 core 2 core Danfoss Randall... -
Page 6: Your Programmer
User Instructions Your programmer The 3060 programmer allows you to switch your hot water and heating on and off at times that suit you. Four tappets on the timing dial let you decide when you want your hot water and heating to come on and go off each day. The programmer provides 2 ON times and 2 OFF times per day. Using the lower dial you can choose how you control your Heating and Hot Water, either at the set times, constantly ON, constantly OFF (each in different combinations). During the summer the central heating can be turned off, whilst still controlling the hot water at the set times. Programming the unit There are four TAPPETS on your timing dial, two red and two blue: o the red tappets are the ON switches o the blue tappets are the OFF switches 1. Hold the central black & silver knob with one hand and move the red tappet marked ‘A’ clockwise to the time you want your HEATING/HOT WATER to switch on in the morning. NB. you may find the tappets quite stiff, so you may have to push them quite firmly to move them. -
Page 7: Setting The Clock
Still holding the central knob, move the blue tappet marked ‘B’ to the time you want your HEATING/HOT WATER to switch off in the morning. You can set your other two tappets in the same w ay to set your HEATING/HOT WATER for the afternoon or evening. EXAMPLE (NB. Clock is in 24 hour mode) If you want your heating and hot water ON between 7am and 10am and ON again between 5pm and 11pm, set tappets as follows: A at 1st ON time = 7 B at 1st OFF time = 10 C at 2nd ON time = 17 D at 2nd OFF time = 23 Setting the Clock o Turn the dial clockwise until the correct time is lined up with the dot labelled TIME NB. clock is in 24 hour mode REMEMBER You will have to reset the time after a power cut and also when the clocks change in Spring and Autumn... -
Page 8: Using The Programmer
Using the Programmer The selector switch is used to select how the 3060 controls your hot water and heating. The heating and hot water can be operated together in various combinations, or the water can be controlled on its own (i.e. during the summer when only hot water is required). H - ONCE H - TWICE W - ONCE W - ONCE H - OFF H - TWICE W - TWICE W - TWICE There are six positions into which the selector switch may be set. 1 - H OFF / W OFF Both Heating and Hot Water will remain OFF until you change the setting. - Page 9 4 - H ON / W ON This is the ‘CONSTANT’ position and the programmer will remain permanently ON for both Heating and Hot Water, irrespective of the position of the tappets. 5 - H TWICE / W ONCE In this position the heating will come on and go off according to the times you have programmed (ON at A, OFF at B, ON at C, OFF at D). The Hot Water will come on at A and stay on until D. 6 - H OFF / W TWICE In this position the Heating will be permanently OFF and the Hot Water will come on and go off according to the times you have programmed (ON at A, OFF at B, ON at C, OFF at D). Note: If hot water is required all day with the heating shut off (i.e.
- Page 12 Still having problems? Call your local heating engineer: Name: Tel: Visit our website: www.heating.danfoss.co.uk Email our technical department: ukheating.technical@danfoss.com Call our technical department 0845 121 7505 (8.45-5.00 Mon-Thurs, 8.45-4.30 Fri) For a large print version of these instructions please contact the Marketing Services Department on 0845 121 7400. Danfoss Ltd Ampthill Road Bedford MK42 9ER Tel: 01234 364621 Fax: 01234 219705 Part No. 7485v03 06/08...
Need help?
Do you have a question about the 3060 and is the answer not in the manual?
Questions and answers