Table of Contents
Advertisement
V I I . C A R E A N D M A I N T E N A N C E
Follow these easy steps for a quick and safe repair for
both pneumatic and solid tires:
1. Turn off the power to the controller.
2. Make sure that the power chair is in drive mode. See
figure 5.
3. Raise and support the power base so that the wheel is
at least 1 in. (2.5 cm) off of the ground.
4. Remove the drive wheel nut and washer from the axle.
See figure 19.
5. Remove the drive wheel from the axle. Make sure that
you keep the key.
6. Replace the entire assembly.
7. Slide the wheel back onto the axle. Make sure that the
key is in the axle slot.
WARNING! Ensure that the axle key is
properly installed into the axle slot when
mounting the wheel. If not installed
securely,
disengaged which may cause personal
injury and/or product damage may result.
8. Reinstall the drive wheel nut and washer onto the axle and tighten. See figure 19.
NOTE: Any nylon insert lock nut removed during the disassembly or adjustment of the power chair must be
replaced with a new nut. Nylon insert lock nuts should not be reused as it may cause damage to the nylon insert,
resulting in a less secure fit. Replacement nylon insert lock nuts are available at local hardware stores or
through your authorized Pride Provider.
WARNING! Make sure both the nut and the washer are reinstalled and tightened properly.
9. Remove the power chair from the base support.
Battery Replacement
A battery wiring diagram is printed on a decal located on the power base. See VI. "Batteries and Charging" for
correct battery specifications.
You may need the following to change your batteries:
metric/standard socket set and ratchet
adjustable wrench
Jazzy Elite ES Series
the
braking
system
MANDATORY! Battery posts, terminals, and related accessories contain lead and
lead compounds. Wear goggles and gloves when handling batteries and wash hands
after handling.
WARNING! The batteries in your power chair should only be serviced or replaced by
an authorized Pride Provider or a qualified technician.
WARNING! Do not replace batteries when seat is occupied.
WARNING! Power chair batteries are heavy. See specifications table. If you are
unable to lift that much weight, be sure to get help. Use proper lifting techniques
and avoid lifting beyond your capacity.
WARNING! Do not mix old and new batteries. Always replace both batteries at the
same time.
PROHIBITED! Keep tools and other metal objects away from the battery terminals.
Contact with tools can cause electrical shock.
www.pridemobility.com
MOTOR
AXLE
is
Figure 19. Jazzy Elite ES Series Drive Wheel
Removal
KEY
DRIVE
WHEEL
DRIVE WHEEL WASHER
DRIVE WHEEL NUT
27
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the Jazzy Elite ES and is the answer not in the manual?
Questions and answers
Put the chair in gear and the lights won't quit blinking
The lights on the Pride Mobility Jazzy Elite ES may be blinking when the chair is put in gear due to an issue with the battery condition or electrical connections. Possible causes include loose harness connections, a tripped circuit breaker, or weak batteries. Checking and securing the connections, resetting the circuit breaker, and load testing the batteries can help diagnose the issue. If the problem persists, contacting an authorized Pride Provider is recommended.
This answer is automatically generated
How do I get the batteries out of the Jazzy ES Elite? I fined to remove the seat, please tell me how.
To remove the batteries from the Pride Mobility Jazzy Elite ES:
1. Turn off the power to the controller.
2. Make sure the power chair is in drive mode.
3. Remove the seat.
4. Remove the main shroud by lifting the rear of the shroud until it disconnects, then slide it forward and lift it over the seat post.
5. Unfasten the battery strap.
6. Disconnect the battery connectors.
7. Remove the batteries from the power base.
This answer is automatically generated
@Mr. Anderson, thank you for answering but the part I need help with is, how do I remove the seat?
How do I remove the seat to replace the batteries on a Jazzy ES Elite scooter?
To remove the seat to replace the batteries on a Pride Mobility Jazzy Elite ES:
1. Turn off the power to the controller.
2. Make sure the power chair is in drive mode.
3. Remove the seat.
These are the initial steps before accessing the batteries. After removing the seat, you can proceed to remove the main shroud and battery strap.
This answer is automatically generated