B&D Controll-A-Door R Instruction Manual
  1. Manuals
  2. Brands
  3. B&D Manuals
  4. Garage Door Opener
  5. Controll-A-Door R
  6. Instruction manual
B&D Controll-A-Door R Instruction Manual

B&D Controll-A-Door R Instruction Manual

Automatic rolling garage door opener
Hide thumbs
Table of Contents

Advertisement

Quick Links

Controll-A-Door
R
®
Automatic Rolling Garage Door Opener
N1134
Instruction Manual
Instruction Manual
B&D Doors is a Division of B&D Australia Pty Limited A.B.N. 25 010 473 971
www.bnd.com.au
Manufactured under a quality system certified as complying
with IS09002 by an accredited certification body
Part No 059778

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Controll-A-Door R and is the answer not in the manual?

Questions and answers

Related Manuals for B&D Controll-A-Door R

Summary of Contents for B&D Controll-A-Door R

  • Page 1 Controll-A-Door ® Automatic Rolling Garage Door Opener N1134 Instruction Manual Instruction Manual B&D Doors is a Division of B&D Australia Pty Limited A.B.N. 25 010 473 971 www.bnd.com.au Manufactured under a quality system certified as complying with IS09002 by an accredited certification body Part No 059778...

  • Page 2: Important Safety Instructions

    START BY READING THESE IMPORTANT SAFETY RULES These safety alert symbols mean Caution – a personal safety or property damage instruction. Read these instructions carefully. This Automatic Garage Door Opener is designed and tested to offer safe service provided it is installed and operated in strict accordance with the following safety rules.

  • Page 3: Specifications

    ABOUT YOUR B&D OPENER Thank you for choosing a B&D automatic garage door opener. This automatic garage door opener has been designed and developed in Australia by B&D Doors. The technically advanced construction of this B&D opener ensures you enjoy the following benefits: •...
  • Page 4 WHAT YOU MAY NEED TO DO THE JOB ❐ Suitable door support ❐ Ladder ❐ Phillips screwdriver ❐ Suitable sockets and handle with a 150mm extension ❐ 450mm pipe wrench (Stillson) or similar ❐ Adjustable wrench or spanner set ❐ Marking pencil ❐...
  • Page 5 SECTION 1 - REQUIREMENTS IMPORTANT SAFETY INSTRUCTIONS FOR INSTALLATION WARNING - INCORRECT INSTALLATION CAN LEAD TO SEVERE INJURY. FOLLOW ALL INSTALLATION INSTRUCTIONS. AS3350 1.1 DOOR OPERATION The door must be in good operating condition and the maximum effort to move the door up or down, from stationary, should not exceed 200 Newton’s (20kg force) at the bottom rail.
  • Page 6 SIDEROOM Dimension A = 60mm minimum. This is the minimum distance from the door curtain to the inside of the door bracket. Dimension B = 65mm maximum. This is the distance from the door drum to the edge of the door curtain. If dimension B is greater than 65mm, a ring gear adaptor (Part No 59585) will be required.
  • Page 7 SECTION 2 – INSTALLATION PROCEDURES The following is the preferred method of installing the opener 2.1 PREPARATION a. Check the door operation. i. The door must be smooth to operate by hand. ii. Operating force on the bottom rail should not exceed 200 Newton’s (20kg) force. iii.
  • Page 8 No. 10 x 32 screw 2.3 PINNING THE DOOR CURTAIN Washer Pin the door curtain to the door drum at each end of the door to maintain security when the opener closes and locks. With the door fully closed: a. Mark positions to drill in both drums as shown. b.
  • Page 9 Fit the opener as follows: • Disengage the opener by pulling the disengagement handle down (there will be a click), so that the ring gear can be rotated by hand. • Slide the opener over the door axle and into the drum of the door.

  • Page 10: Program The Opener

    2.5 PROGRAM THE OPENER For the garage door opener to function properly the Door Travel Limits, Door Travel Force Settings and Remote Control Transmitter Codes will need to be programmed. If infra red beams are to be fitted they should be installed and connected prior to setting door travel SERVICE limits.
  • Page 11 Note: If the Limit Set button is pressed the Limit Set LED will illuminate to indicate the opener is in Limit Learn – if the garage door is not moved within 40 seconds, the Limit Set LED will turn off and the opener will exit Limit Learn. The opener will constantly monitor the force required to operate the door and will adjust the Door Travel Force as necessary to ensure safe trouble free operation of your garage door opener.
  • Page 12 Step 4 TESTING THE SAFETY SYSTEM The opener automatically adjusts the force required to reverse when closing or to stop when opening when an obstruction is encountered. The operation of the Safety System must be tested whenever there has been any change in settings or any adjustment to the door, and monthly during the operational life of the opener.
  • Page 13 2.6 Programming Optional Remote Control Transmitter Features. Code You can program each button of your multi channel remote control transmitter so that each button performs a different function. You can program each button of a multi channel remote control transmitter to activate one of the following features: SERVICE Code...
  • Page 14 2.9 Code Setting “AUXILLIARY OUTPUT” It is possible to operate other devices (eg alarm systems) using one of the spare buttons of a multi channel remote control transmitter coded into the Auxilliary Output feature. (Refer to Section 3.3 and 4.4 for description of the Auxilliary Output function). Press Code Set Press and release the Code Set button four times, the Code Set LED will flash slowly 4 times...
  • Page 15 SECTION 3 – ACCESSORIES 3.1 Remote Aerial – Part No 062177 Some sites can cause poor radio reception, ie whernever there is a large mass of metal like all steel garages or underground car parks (large masses of steel reinforced concrete). Metal mass can cause the radio signal to be reduced.
  • Page 16 3.3 J8 Connector Connector A variety of wired accessory items can be fitted to the J8 Connector (eg to operate an alarm system). An Interface Cable Kit will need to be fitted to the J8 outlet of the Printed Circuit Board. To install this cable kit you will need to remove the light cover and using a suitable tool, remove the breakout on the cover to allow the wiring to pass through to the opener.
  • Page 17 SECTION 4 - HOW TO OPERATE For maximum efficiency of your opener, your garage door must be in good operating condition. An annual service of the door by an authorised dealer is recommended. (Refer to Warranty conditions in Section 8). Activate the opener only when the door is in full view, free of obstructions and with the opener properly adjusted.
  • Page 18 4.2 Manual Operate Button. Incorporated in the light cover is an operate button. Pressing this button will operate the door, (the same as the remote control transmitter). It is also used to exit from “Vacation Mode” if this feature is activated. If the LEDs are flashing a diagnostic code, pressing this button will reset the opener and stop the flashing LEDs.
  • Page 19 4.6 Safety Infra Red Beam Option A Safety Infra Red Beam Kit (Part No 62153) may be fitted to this opener. • When this option is fitted, the operation of this device is such that if an object (i.e. car, child, etc) blocks the infra red beam, then the garage door opener will not close the door automatically.
  • Page 20 4.11 Auxilliary Output The radio receiver of this garage door opener can be used to operate other devices. Connect an interface cable kit to the J8 Connector on the garage door opener and the device to be controlled (eg an alarm panel, security lights, etc).
  • Page 21 SECTION 5 - MAINTENANCE 5.1 Maintenance The Service LED will indicate the requirement for service Service and/or adjustment. Whilst the Service LED is illuminated Indicator the courtesy light will flash five times each time the door is operated until the Service LED is reset. SERVICE To reset the Service LED when the door is serviced, POWER...
  • Page 22 SECTION 6 – SAVE A SERVICE CALL Symptom Probable Cause(s) Remedy Check the door for normal operation The opener does not work from Garage door in poor condition e.g. - see monthly maintenance. either the button on the light cover springs may be broken or the hand remote control Disengage door locks...
  • Page 23 SECTION 7 – DIAGNOSTIC CODES Slow flashing of the Green Power LED on the front panel indicates the opener is in vacation Mode – see Section 4. If the Service LED is on it indicates the door is overdue for service, if the Service LED is flashing it indicates that there may be a problem that requires urgent attention.
  • Page 24 Diagnostic Code Action Check the wiring to the Safety Infra Red Beams. The wiring may be short circuit or 2 flashes SERVICE open circuit. If there are no faults in the wiring the IR Beam detectors may need 1 flash POWER servicing or replacing.
  • Page 25 Section 8 – Controll-A-Door Automatic Garage Door Opener Warranty Definitions ‘B&D’ means (a) in Australia - B&D Doors of 17 Oasis Court, Clontarf Queensland 4019, a division of B&D Australia Pty Ltd (ABN 25 010 473 971), or (b) in New Zealand - B&D Doors NZ Pty Ltd of 70 Allens Road East Tamaki Auckland, which is a subsidiary of B&D Australia Pty Ltd.
  • Page 26 Subject to paragraph 12 hereof; the obligations of B&D under this warranty are limited to those contained herein and such warranties are expressly in lieu of all other warranties, express or implied, including any implied warranty of merchantability or fitness for a particular purpose and notwithstanding any course of dealing between the parties or custom and usage in the trade to the contrary.
  • Page 27 There is a range of additional accessories for your added convenience and security. • Safety Infra Red Beams. Gives additional protection if the door is closing onto your property or person. Simply breaking the beam “stops” the door! Must be fitted if autoclosing feature is operational – Part No 62153 •...
  • Page 28 For Product support within Australia contact 1800 636 407 QLD Office: B&D Doors, 17 Oasis Court, Clontarf 4019. Ph: (07) 3883 0200 NSW Office: B&D Doors, 34-36 Marigold Street, Revesby 2212. Ph: (02) 9722 5555 VIC/TAS Office: B&D Doors, 147-153 Canterbury Road, Kilsyth 3137. Ph: (03) 9237 7766 SA Office: B&D Doors, 23 Frederick Road, Royal Park 5014.

Table of Contents

Save PDF