Morso 1630 Instructions For Installation And Use Manual
Hide thumbs
Also See for 1630:
- Instruction manual (12 pages) ,
- Assembly and user instructions manual (12 pages) ,
- Supplementary installation & operation instructions (12 pages)
Table of Contents
Related Manuals for Morso 1630
Summary of Contents for Morso 1630
- Page 1 Instructions for Installation and Use 1630 EN 13240 MORSØ JERNSTØBERI A/S . DK-7900 NYKØBING MORS MORSØ JERNSTØBERI A/S . DK-7900 NYKØBING MORS E-Mail: stoves@morsoe.com · Website: www.morsoe.com E-Mail: stoves@morsoe.com · Website: www.morsoe.com...
-
Page 2: Table Of Contents
ENjOy yOUR NEw MORSø STOvE! Morsø, the largest stove manufacturer in Denmark, has been making cast-iron stoves of the highest qual- ity since 1853. By carefully following the instructions below, we are certain that you will enjoy many years of comfortable warmth from your new Morsø... -
Page 3: Installing Your Morsø Stove
1.0 INSTALLINg yOUR MORSø STOvE 1.1 Unpacking the stove 1630: After removing the outer packaging, flatten it and lay onto the floor close to the stove; this can then act as protective work surface during the assembly process. Next, remove the legs and bolts from inside the stove. Gently lay the stove onto its back and unscrew it from the wooden pallet. -
Page 4: The Chimney
600 mm 850 mm uninsulated flue 1630 corner installation On the floor National and Local Building Regulations must again be observed when considering the type, thickness and area of the hearth to be used in the installation. The hearth temperature under safety test was less than 65°C. -
Page 5: Pipe Connections
The cross-sectional area of the chimney (at its narrowest point) must comply with National and Local Building Regulations. Generally, the area needed for a Morsø wood-burning stove instal- lation should measure at least 175 cm2 (150 mm diameter). An over-sized chimney is generally hard to keep warm and results in poor draft. In cases where there is an oversized masonry chimney, it is recommended that the chimney be lined using an appropriate chimney lining system with the correct internal diameter. - Page 6 1.7 Connecting the stove to a masonry chimney A wall sleeve should be bricked securely into the wall of the chimney at the appropriate height and the stovepipe inserted centrally. The pipe must not extend into the actual chimney opening, but rather must reach only to the inside of the chimney aperture.
-
Page 7: Draft Conditions
1.9 Draft conditions If smoke spillage occurs when the fire door is opened, it is probably due to poor chimney draft. This type of stove requires at least 12 pa of chimney draft to achieve satisfactory combustion and smoke spillage prevention. However, in cases where the stove door is opened too vigorously you could expect that slight smoke spillage may occur. - Page 8 2.0 FIRINg ThE STOvE/USINg yOUR STOvE The heat output of your stove is regulated by means 3 air inlets. The primary air supply, i.e. the air which passes through the shaking grate, is controlled by the lower air control on the door, while the secondary air supply is controlled by the 2 upper air controls.
- Page 9 2.1 Lighting and refuelling intervals Kindling (dry sticks) requires a large volume of air for quick combustion. When lighting the stove from cold it will help to keep the main door ajar (2-3cms) for the first few minutes. The primary and secondary air supplies should be fully open during lighting. When firing with wood only, the riddling grate would normally be in the closed position (push the riddling handle under the ash-lip backwards).
- Page 10 5. Refuelling of your stove should be done while there are still glowing embers in the bed. Spread the embers across the bottom, but concentrated most- ly towards the front of the stove. 6. Place three pieces of fuel weighing roughly 2-3 kg across the embers in one layer, with spacing of roughly 1 cm between the pieces of wood.
- Page 11 The stove door should normally be opened gently the first 2 - 3 centimetres, then you should wait until the pressure has equalised before opening the door all the way. This technique will prevent smoke from getting out, particularly when there is a poor draught. The stove door should never be opened when the stove is being fired vigorously.
-
Page 12: Routine Stove Maintenance
3.0 ROUTINE STOvE MAINTENANCE 3.1 External maintenance The surface of the stove is painted with heat-resistant Senotherm paint. If the stove is used too vigorously, the painted surface may take-on a greyish tinge. It is easily maintained by simply vacuuming the surface with a soft brush attachment and applying two light layers of paint. Morsø... -
Page 13: Cleaning The Stove
Reasons for premature wear of internal parts • Stove being used/fired too vigorously • Too little air passing through the bottom grate • Use of excessively dry wood (wood from old furniture) • Excessive debris collection on baffle plate or inner fireback (see section on cleaning) •... -
Page 14: Alternative Fuel Types
4.0 ALTERNATIvE FUEL TyPES Your new Morsø stove is EN-approved for burning wood. However, the stove is capable of burning other solid fuels as manufactured smokeless coal or good quality anthracite (stove nuts). If you fire your stove with any fuel other than wood, it may help to use coal insert/fuel economisers (available for most models), which simply fit into the left and right sides of the firebox. - Page 15 In order to maintain the combustion process, the entire grate area must remain covered by glowing coals. If the coal layer is too shallow you will have less heat and it would not be neces- sary to supply air via the top vent. You must empty the ash pan whenever it becomes full.
- Page 16 Morsø Jernstøberi A/S - 03.12.2009 - 72161400 Morsø Jernstøberi A/S 72161400 MORSØ JERNSTØBERI A/S . DK-7900 NYKØBING MORS E-Mail: stoves@morsoe.com · Website: www.morsoe.com...
Need help?
Do you have a question about the 1630 and is the answer not in the manual?
Questions and answers