Subscribe to Our Youtube Channel
Related Manuals for Euroboor ECO.100/4
Summary of Contents for Euroboor ECO.100/4
-
Page 1: Table Of Contents
USER MANUAL TO REDUCE THE RISK OF INJURY USER MUST READ AND UNDERSTAND INSTRUCTION MANUAL ECO.100/4 Magnetic Drilling Machine SERIAL NO._______________ DATE OF PURCHASE _____________... -
Page 2: Table Of Contents
1 - Table of Contents Table of Contents …………………………………………………………………………………………………… page 1 Safety …………………………………………………………………………………………………………………….. page 2 Before Use ……………………………………………………………………………………………………………… page 3 Items Included in Delivery ………………………………………………………………………………………. page 4 The Hole Cutter Hole Cutter Selection ....................page 5 Cooling/Lubrication ....................page 6 Tool Assembly Morse Taper Assembly …………………..…………………………………………………………………... -
Page 3: Safety
5. Do not wear any loose clothing or jewellery that may get entangled in the moving parts of the magnetic drilling machine. 6. Use only accessories or parts that are recommended by Euroboor. 7. During drill operations, the hole cutter must be cooled and lubricated with good quality cutting or lubrication oil. -
Page 4: Before Use
DC current. Make sure the magnetic drilling machine is connected to a stable power supply. Euroboor do not recommend the use of a generator or other mobile power supply for power supply. Euroboor does not recommend the use of extension cables. If there is no other way, use good quality cables and keep extension cables as short as possible. -
Page 5: The Hole Cutter
Hole Cutter selection There are many different types of steel. It is not possible to drill all these types of steel with 1 type of cutter. Euroboor recommended the following : Euroboor+ HSS Series For drilling holes in general 37/52 steel and aluminium... -
Page 6: Cooling/Lubrication
Holes for cooling and lubrication oil Fixing screws of Morse Conus Euroboor recommends the use of cooling and lubrication agents. Not only do these assist in drilling but they will also lengthen the lifespan of your tools. One of the advantages of the use of hole cutters is that cooling and lubrication agent scan be supplied from the inside, so that the agents end up in the right place. -
Page 7: Drill Chuck Assembly
Installation of 13mm Chuck directly on the motor unit For the ECO.80 and ECO.100/4 magnetic drilling machines it is possible to install a drill Chuck directly to the shaft extending from the motor unit. Attach to the drill chuck with article number IBK.13-B16 a adaptor with article number B16-MC3. -
Page 8: The Control Panel
All-time electronic Temperature protection : The ECO.100/4 is equipped with a all-time electronic temperature protection. If the temperature of the motorunit runs upto 70 Degree Celsius the motorunit will stop. After a few minutes it can be started again and we recommend... -
Page 9: Speed Gearbox
4-speed Manual Gearbox The ECO.100/4 is equipped with a 4-speed gearbox. The two gear switches makes it possible to choose 4 manual speeds. Also does the ECO.100/4 have a electronic speed adjustment so every wanted speed can be selected. Important is that the closest mechanical gear is selected first and after that the speed can be decreased by the electronic adjustment. -
Page 10: Drilling
Drill the hole on the recommended size of the tap. Do not turn the magnet off to keep the machine on its position. Take the cutter out and use a tap collet (Euroboor TCM series) to fix the tap to the machine. These TCM adapters exist in several DIN and ISO norms and are based on the shaft diameter of the tap that is used. -
Page 11: Maintenance
Repair, modification and inspection of Euroboor Magnetic drilling machines must be done by a Euroboor authorized dealer. The parts list will be helpful if presented with the machine to the Euroboor dealer for service when requesting repair or other maintenance. -
Page 12: Spareparts & Exploded View
6 - Spare parts & Exploded view 100.4001 Frame 100.4312 Friction Clutch complete 100.0006 Screw SSM8x25 100.0372 Carbon Brush Holder 100.0031 Washer M8 100.4383 Field 230v 020.0096 Setting Nut 100.4384 Field 110v 020.0138 Setting Screw 100.4388 Housing 100.0038 Magnet Base 100.0391 Baffle 020.0201... - Page 13 Important notice : Because of minor changes to our machines it is recommended to provide the framenumber of your machine when ordering spareparts. This number can be found on front of machine at magnetic base and frame. When you have any doubt when ordering spareparts, please contact your supplier before ordering.
Need help?
Do you have a question about the ECO.100/4 and is the answer not in the manual?
Questions and answers