Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Eagle I
Summary of Contents for Eagle I
-
Page 2: Table Of Contents
All rights reserved. No part of this manual may be reproduced in any means: graphics, electronics, or mechanical, including photocopying with- out the expressed written permission of the publisher. Materials, compo- nents and specifications are subject to change without notice. Eagle Access Control Systems, Inc. / (800) 708-8848- / www.eagleoperators.com... -
Page 3: Ul Listings
A wireless contact sensor shall function under the intended end use conditions. Eagle Access Control Systems, Inc. / (800) 708-8848 / www.eagleoperators.com... - Page 4 (five or more single family units), locations not servicing the general public, in hotel, garages, retail store, or other buildings which unauthorized access is prevented via servicing the general public. supervision by security personnel. Eagle Access Control Systems, Inc. / (800) 708-8848 / www.eagleoperators.com...
-
Page 5: Installing The Warning Sign / Precautions
____________________ CAUTION! Be sure to read and follow all the Eagle Access Control Systems, Inc. and UL instructions before installing and operating any Eagle Access Control Systems, Inc. products. Eagle Access Control Systems, Inc. is not responsible for any improper installation procedures caused by installer or user failing to comply with local building codes. -
Page 6: Instructions On Gate Posts
Example A. To do so will cause the gate to hit the post in certain instances. Eagle Access Controls only recommends installation of catch rollers on the side of a post with a minimal distance of 4" (Four inches) between the rollers as shown in Example B. -
Page 7: Methods Of Installation
Minimum space between gate and output sprocket must be 4". After you position the gate operator, bolt-down the operator to the concrete bed. Make CORRECT certain the concrete bed is solid. Eagle Access Control Systems, Inc. / (800) 708-8848 / www.eagleoperators.com... -
Page 8: Mounting Operator(S) To Concrete Pad(S)
To select the opening direction of the gate, use the Feature Selector (as shown). Select switch #2 to the "open left" position for left opening. Use switch #2 to the "open right" position for right opening. EAGLE Eagle Access Control Systems, Inc. / (800) 708-8848 / www.eagleoperators.com... -
Page 9: Connecting The Power
REVERSE LOOP with a proper LOOP CUT seal. EXIT LOOP TWISTED WIRES PROPER SEALER WIRE LAYERS SHOULD BE USED IN LOOP CUT IN LOOP CUTS Eagle Access Control Systems, Inc. / (800) 708-8848 / www.eagleoperators.com... -
Page 10: Two Way Adjustable Reverse Sensors / Erd
When Adjusting Sensors Remember... Too Sensitive = if the gates stops or reverses by itself Not Sensitive enough = if the gate strikes an object and does not stop or reverse Eagle Access Control Systems, Inc. / (800) 708-8848 / www.eagleoperators.com (10) -
Page 11: The Feature Selector
Note: If the power light is on and the operator does not function, press the reset button once. If this does not solve the problem, proceed with turning off the power switch and then switching it back on again. Eagle Access Control Systems, Inc. / (800) 708-8848 / www.eagleoperators.com (11) -
Page 12: Master And Slave Operation
Use the feature selector to choose available features by designating the various switches (1 through 4). Gate opening direction, motor brake and close timer. Please refer to page 10 for more information on individual switch functions. Eagle Access Control Systems, Inc. / (800) 708-8848 / www.eagleoperators.com (12) -
Page 13: Slave Control
"off" position. Switch #2 must be set to the "open left" or to the "open right" position. Switch #3 brake on / off. Switch #4 Not in use. Eagle Access Control Systems, Inc. / (800) 708-8848 / www.eagleoperators.com (13) -
Page 14: Describing The Output Connections
However, by selecting the "On" position, the system will automatically reset itself. Power (24 VAC) The Control Board provides 24 VAC Power, which can be used for loop detectors and receivers. Eagle Access Control Systems, Inc. / (800) 708-8848 / www.eagleoperators.com (14) -
Page 15: Connecting The Accessories
With the exeption of the MAG Lock, all of these accessories can be installed on the Master or Slave operator. Photo Eye MAG Lock Reverse Loop Phantom Loop Key Lock Box Fire Lock Box Edge Sensor Exit Loop Phone Entry System Eagle Access Control Systems, Inc. / (800) 708-8848 / www.eagleoperators.com (15) -
Page 16: Description Of Inputs
Once activated the gate will fully close. Activation while the gate is opening has no effect. Multiple devices may be connected in parallel to the Edge Sensor Input. Eagle Access Control Systems, Inc. / (800) 708-8848 / www.eagleoperators.com (16) -
Page 17: Receiver Connections
Follow these instructions to appropriately set the limit switches. Limit Switches Adjust cams for proper stoppage Limit Switches Be sure that the locking plate is locked into place after each adjustment Eagle Access Control Systems, Inc. / (800) 708-8848 / www.eagleoperators.com (17) - Page 18 (TOP VIEW) GATE OPENING Edge Sensors should be appropriately installed at Eagle Operator recommended locations to All Edge Sensors are shown ensure proper entrapment at recommended locations. protection against injury. Eagle Access Control Systems, Inc. / (800) 708-8848 / www.eagleoperators.com (18)
- Page 19 Eagle Access Control Systems, Inc. 13286 Paxton Street Pacoima, CA 91331 Tel: 818-899-2777 Fax: 818-899-2666 Toll Free: 800-708-8848 www.EagleOperators.com...
Need help?
Do you have a question about the I and is the answer not in the manual?
Questions and answers