Page 4
RESTRICTED RIGHTS. Use, duplication or disclosure by the Government is subject to the GSA ADP Schedule contract with Lenovo Group Limited, if any, or the standard terms of this commercial license, or if the agency is unable to accept this Program under these terms, then we provide this Program under the provisions set forth in Commercial Computer Software–Restricted Rights at FAR 52.227-19, when applicable, or under Rights in...
Page 6
Information resources . Online Books folder ThinkVantage Productivity Center . Access Help . Warranty and safety www.lenovo.com Help and service Using the documentation and diagnostic programs . Calling for service . Using other services Purchasing additional services . Appendix A. Manual modem commands .
Note: If you notice these conditions with a product (such as an extension cord) that is not manufactured for or by Lenovo, stop using that product until you can contact the product manufacturer for further instructions, or until you get a suitable replacement.
Danger Hazardous moving parts. Keep fingers and other body parts away. Attention Before replacing any CRUs, turn off the computer and wait three to five minutes to let the computer cool before opening the cover. Power cords and power adapters Use only the power cords and power adapters supplied by the product manufacturer.
In addition, many mobile products, such as notebook computers, utilize a rechargeable battery pack to provide system power when in portable mode. Batteries supplied by Lenovo for use with your product have been tested for compatibility and should only be replaced with approved parts.
shorten the life of the battery and can also pose a safety hazard. Do not let rechargeable Lithium-Ion batteries completely discharge or store these batteries in a discharged state. Heat and product ventilation Computers generate heat when turned on and when batteries are charging. Notebook PCs can generate a significant amount of heat due to their compact size.
v Do not bend or flex CD/DVD discs, or force them into the computer or their packaging v Check CD/DVD discs for cracks before each use. Do not use cracked or damaged discs Additional safety information Danger Electrical current from power, telephone, and communication cables is hazardous.
Do not use the telephone to report a gas leak in the vicinity of the leak. Laser compliance statement Some personal computer models are equipped from the factory with a CD-ROM drive or a DVD-ROM drive. CD-ROM drives and DVD-ROM drives are also sold separately as options.
Power supply statement Never remove the cover on a power supply or any part that has the following label attached. Hazardous voltage, current, and energy levels are present inside any component that has this label attached. There are no serviceable parts inside these components. If you suspect a problem with one of these parts, contact a service technician.
Chapter 8, “Getting information, help, and service,” on page 59 provides information about the wide variety of helpful resources available from Lenovo. v Appendix A, “Manual modem commands,” on page 63 provides commands for manually programming your modem.
Where it is impossible to avoid reflections or to adjust the lighting, an antiglare filter placed over the screen might be helpful. However, these filters might affect the clarity of the image on the screen; try them only after you have exhausted other methods of reducing glare.
Page 20
3. Connect the USB mouse cable to a USB connector. 4. Connect the monitor cable to the monitor connector on the computer. v If you have a Video Graphics Array (VGA) Standard monitor, connect the cable to the connector as shown. Note: If your model has two monitor connectors, be sure to use the v If you have a digital video interface (DVI) monitor, connect the cable to the connector as shown.
Page 21
5. If you have a modem, connect the modem using the following information. L I N This illustration shows the two connections on the back of the computer that are needed to set up your modem. In the United States and other countries or regions that use the RJ-11 telephone outlet, attach one end of the telephone cable to the telephone and the other end to the telephone connector on the back of the computer.
Page 22
7. If you have powered speakers with an ac adapter, use the following instructions. a. Connect the cable that runs between the speakers, if necessary. On some speakers, this cable is permanently attached. b. Connect the ac adapter cable to the speaker. c.
1 USB 2 Serial 3 S-video 4 Parallel 5 Ethernet 6 MIDI/joystick 7 IEEE 1394 10. Connect the power cords to properly grounded electrical outlets. Note: Refer to the Access Help online help system for more information about connectors. See “Access Help” on page 60 for instructions on how to open the online help system.
Finishing the software installation Important Read the license agreements carefully before using the programs on this computer. These agreements detail your rights, obligations, and warranties for the software on this computer. By using these programs, you accept the terms of the agreements. If you do not accept the agreements, do not use the programs.
Installing other operating systems If you install your own operating system, follow the instructions that come with your operating system CDs or diskettes. Remember to install all device drivers after you install your operating system. Installation instructions are usually provided with the device drivers. Updating your antivirus software Your computer comes with the Symantec Client Security software you can use to detect and eliminate viruses.
Before you install or remove any option, read “Important safety information” on page v. These precautions and guidelines will help you work safely. Note: Use only the parts provided by Lenovo. Features This section provides an overview of the computer features and preinstalled software.
Page 28
® v Intel Celeron D processor ™ v Intel Core 2 Duo processor v Internal cache (size varies by model type) Memory v Support for two double data rate 2 dual inline memory modules (DDR2 DIMMs) v Flash memory for system programs (varies by model type) Internal drives v 3.5-inch, half-inch (slim) diskette drive (some models) v Serial Advanced Technology Attachment (SATA) internal hard disk drive...
Page 29
1. The operating systems listed here are being certified or tested for compatibility at the time this publication goes to press. Additional operating systems might be identified by Lenovo as compatible with your computer following the publication of this booklet. Corrections and additions to this list are subject to change. To determine if an operating system has been certified or tested for compatibility, check the Web site of the operating system vendor.
– PCI Express x1 adapter – Optical drive, such as CD drives and DVD drives (some models) – Hard disk drive For the latest information about available options, see the Lenovo Web site at http://www.lenovo.com/ or contact your reseller or marketing representative. User Guide...
Specifications This section lists the physical specifications for your computer. Dimensions Width: 310 mm (12.2 in.) Height: 85 mm (3.35 in.) Depth: 358 mm (14.1 in.) Weight Minimum configuration as shipped: 7.3 kg (16 lbs) Maximum configuration: 8.5 kg (18.7 lbs) Environment Air temperature: Operating at 0 - 3000 ft (914.4 m): 10°...
Supported operating positions To provide proper air flow to internal components, you must position your computer in one of the positions as illustrated below. Tools required To install some options in your computer, you might need a flat-blade or Phillips screwdriver.
v When possible, remove the option and install it directly in the computer without setting the option down. When this is not possible, place the static-protective package that the option came in on a smooth, level surface and place the option on it.
Locating connectors on the rear of your computer The following illustration shows the locations of connectors on the rear of your computer. Power cord connector Cable lock latch PCI Express x1 adapter connector PCI adapter connector USB connectors (4) Ethernet connector USB connectors (2) Note: Some connectors on the rear of your computer are color-coded to help you determine where to connect the cables on your computer.
Audio line out connector Obtaining device drivers You can obtain device drivers for operating systems that are not preinstalled at http://www.lenovo.com/support/ on the World Wide Web. Installation instructions are provided in README files with the device-driver files. Description Used to attach a device that requires a Universal Serial Bus (USB) connection, such as a USB keyboard, USB mouse, USB scanner or USB printer.
Opening the cover Important Read “Important safety information” on page v and “Handling static-sensitive devices” on page 16 before opening the computer cover. To open the computer cover: 1. Remove any media (diskettes, CDs, or tapes) from the drives, shut down your operating system, and turn off all attached devices.
Locating components The following illustration will help you locate the various components in your computer. Diskette drive lock Microprocessor and heat sink Memory modules (2) Battery PCI riser assembly Power supply assembly Internal speaker Hard disk drive Optical drive Optical drive lock Diskette drive Chapter 3.
Accessing system board components and drives You might need to pivot the drive bay assembly upward and remove the PCI riser and adapters to access system board components such as memory, the battery, and to access the drives. To access system board components and the drives: 1.
Identifying parts on the system board The system board (sometimes called the planar or motherboard) is the main circuit board in your computer. It provides basic computer functions and supports a variety of devices that are factory-installed or that you can install later. The following illustration shows the locations of parts on the system board.
Installing memory Your computer has two connectors for installing double date rate 2 dual inline memory modules (DDR2 DIMMs) that provide up to a maximum of 4.0 GB of system memory. When installing memory modules, the following rules apply: v Use 1.8 V, 240-pin, double data rate 2 synchronous dynamic random access memory (DDR2 SDRAM).
What to do next: v To work with another option, go to the appropriate section. v To complete the installation, go to “Closing the cover and connecting the cables” on page 35. Installing PCI adapters This section provides information and instructions for installing and removing PCI adapters.
5. Install the adapter into the appropriate connector in the PCI riser. Note: The top connector is for the PCI adapter and the bottom connector is for 6. Close the adapter latch to retain the adapters. 7. Reinstall the PCI riser assembly. What to do next: v To work with another option, go to the appropriate section.
Drive specifications Your computer comes with the following factory-installed drives: v A 3.5-inch hard disk drive in bay 1 v An optical drive in bay 2 (some models) v A 3.5-inch diskette drive in bay 3 (some models) Any bay that does not have a drive installed has a static shield and bay panel installed.
Installing a drive in bay 2 To install an optical drive or an additional hard disk drive in bay 2, do the following: 1. Open the computer cover. See “Opening the cover” on page 20. 2. Pivot the drive bay assembly upward to gain access to the cable connections. 3.
Page 45
Note: If you are installing a 3.5-inch hard disk drive you must use a Universal Adapter Bracket, 5.25 to 3.5-inch. You can obtain this bracket from a local computer retailer or by contacting the Customer Support Center. 7. Reinstall the front bezel. 8.
4. Locate one of the extra five-wire power connectors and connect it to the drive. What to do next: v To work with another option, go to the appropriate section. v To complete the installation, go to “Closing the cover and connecting the cables”...
Page 47
3. Remove the front bezel by releasing the tab as shown and pivoting the bezel outward from the bottom. 4. Lower the drive bay assembly. 5. Remove the metal shield from the diskette drive bay by using a flat-blade screwdriver to gently pry it loose. 6.
10. Install the new drive from the rear of the drive bay assembly and slide the diskette drive lock 1 to the locked position. What to do next: v To work with another option, go to the appropriate section. v To complete the installation, go to “Closing the cover and connecting the cables”...
The cable lock also locks the buttons used to open the computer cover. This is the same type of lock used with many laptop computers. You can order a security cable directly from Lenovo. Go to http://www.lenovo.com/support/ and search on Kensington.
Refer to “Lithium battery notice” on page x for information about replacing and disposing of the battery. To change the battery: 1. Turn off the computer and disconnect the power cord from the electrical outlet and from the computer. 2. Open the computer cover. See “Opening the cover” on page 20. 3.
7. Close the computer cover and connect the power cord. See “Closing the cover and connecting the cables.” 8. Restart the computer, leave it on for approximately 10 seconds. Turn off the computer by holding the power switch for approximately 5 seconds. The computer will turn off.
Page 52
5. Install any locking devices such as a cable lock as necessary. 6. Reconnect the external cables and power cords to the computer. See “Locating connectors on the rear of your computer” on page 18. 7. To update the configuration, see Chapter 5, “Using the Setup Utility,” on page User Guide...
Rescue and Recovery program to restore the contents of the primary hard drive to a previously saved state. This chapter will help you become familiar with recovery solutions provided by Lenovo. The Rescue and Recovery program has two components, Rescue and Recovery (Windows environment) and Rescue and Recovery workspace.
To use Product Recovery discs, do the following: Attention: When you restore the factory contents from the Product Recovery discs, all files currently on the hard disk will be deleted and replaced by the original factory contents. During the restore process, you will be given the opportunity to save one or more files currently on your hard disk drive to other media before any data is removed.
2. From the Rescue and Recovery main window, click the Restore your system from a backup icon. 3. Follow the instructions on the screen. For information about performing a restore operation from the Rescue and Recovery workspace, see “Using the Rescue and Recovery workspace.” Using the Rescue and Recovery workspace The Rescue and Recovery workspace resides in a protected, hidden area of your hard disk that operates independently from the Windows operating system.
v To rescue files from your hard disk or from a backup, click Rescue files in the Rescue and Recovery menu; then, follow the instructions on the screen. v To restore your hard disk from a Rescue and Recovery backup or to restore your hard drive to the factory contents, click Restore your system in the Rescue and Recovery menu;...
1. Start your computer and operating system. 2. Using an Internet browser, go to the following Web address: http://www.lenovo.com/think/support/site.wss/document.do?lndocid=MIGR-54483 3. Insert a diskette into diskette drive A. Information on the diskette will be erased and the diskette will be formatted appropriately.
The latest device drivers for factory-installed devices are also available on the World Wide Web at http://www.lenovo.com/support/. To reinstall a device driver for a factory-installed device, do the following: 1. Start your computer and operating system.
Page 59
7. Use the down-arrow key to select Save and exit the Setup Utility, then press Enter. 8. When the Setup Confirmation window appears, press Enter. 9. The computer restarts. Note: If you are using an external device, you first must turn off your computer before connecting the external device.
v Setup Utility program and hard disk drive passwords are not case sensitive v Not be your name or your user name v Not be a common word or a common name v Be significantly different from your previous password User Password When a User Password is set, the user is prompted to type a valid password each time the computer is turned on.
Note: Selecting a startup device from the Startup Device menu does not permanently change the startup sequence. Changing the startup device sequence To view or permanently change the configured startup device sequence, do the following: 1. Start the Setup Utility program (see “Starting the Setup Utility program” on page 45).
Lenovo might make changes and enhancements to the POST/BIOS. When updates are released, they are available as downloadable files on the Lenovo Web site at http://www.lenovo.com. Instructions for using the POST/BIOS updates are available in a .txt file that is included with the update files. For most models, you can download either an update program to create a system-program-update (flash) diskette or an update program that can be run from the operating system.
Note: Due to constant improvements being made to the Web site, Web page content (including the links referenced in the following procedure) is subject to change. 1. From your browser, type http://www.lenovo.com/support in the address field and press Enter. 2. Locate the Downloadable files for your machine type as follows: a.
Page 67
15. Close the computer cover and reconnect any cables that were disconnected. 16. Turn on the computer to restart the operating system. Chapter 6. Updating system programs...
PC-Doctor for Windows and PC-Doctor for DOS, save and print the log files created by both diagnostic programs. You will need the log files when you speak to a Lenovo technical support representative. (The log file created by PC-Doctor for Windows is automatically saved in C:\PCDR\DETAILED.TXT.) User Guide the computer.
To create a diagnostic CD image, download a self-starting bootable CD image (known as an .iso image) of the diagnostic program from http:// www.lenovo.com/support/. After you download the image, you can create the CD using any CD burning software. If your computer does not have a CD burner or you do not have Internet access, see “Creating diagnostic diskettes.”...
6. Follow the instructions on the screen. 7. When prompted, insert a blank, formatted diskette into the diskette drive and continue to follow the instructions on the screen. 8. When the operation is complete, remove the diskette and click Quit. 9.
Optical mouse An optical mouse uses a light-emitting diode (LED) and an optical sensor to navigate the pointer. If the pointer on the screen does not move smoothly with the optical mouse, you might need to clean the mouse. Use the following procedure to clean the optical mouse: 1.
Page 74
To clean a mouse with a ball, follow the instructions below: 1. Turn off your computer. 2. Disconnect the mouse cable from the computer. 3. Turn the mouse upside down. Twist the retainer ring 1 to the unlocked position to remove the ball. 4.
Chapter 8. Getting information, help, and service If you need help, service, or technical assistance or just want more information about products manufactured by Lenovo, you will find a wide variety of sources available from Lenovo to assist you. Information resources This section provides information on how to access useful resources relating to your computing needs.
The Lenovo Web site (www.lenovo.com) provides an extensive amount of information and services to help you buy, upgrade, and maintain your computer. You can access the most up-to-date information for your computer on the Lenovo Web site. From the www.lenovo.com Web site, you can also: v Shop for desktop and notebook computers, monitors, projectors, upgrades and accessories for your computer, and special offers.
Engineering Change management - Occasionally, there might be changes that are required after a product has been sold. Lenovo or your reseller, if authorized by Lenovo, will make selected Engineering Changes (ECs) available that apply to your hardware.
Service availability and service name might vary by country or region. For more information about these services, go to the Lenovo Web site at http://www.lenovo.com. User Guide...
Page 80
Command Sr=n User Guide Function Force modem off-hook (make busy) Note: H1 command is not supported for Italy Display product-identification code Factory ROM checksum test Internal memory test Firmware ID Reserved ID Low speaker volume Low speaker volume Medium speaker volume High speaker volume Internal speaker off Internal speaker on until carrier detected...
Extended AT commands Command &C_ &D_ &F_ &G_ &K_ &M_ &P_ &R_ &S_ &T_ &V Function &C0 Force Carrier Detect Signal High (ON) &C1 Turn on CD when remote carrier is present &D0 Modem ignores the DTR signal &D1 Modem returns to Command Mode after DTR toggle &D2 Modem hangs up, returns to the Command...
Command &W_ +MS? +MS=? +MS=a,b,c,e,f MNP/V.42/V.42bis/V.44 commands Command &Q_ +DS44=0, 0 +DS44=3, 0 +DS44? +DS44=? User Guide Function &V1 Display Last Connection Statistics &W0 Stores the active profile as Profile 0 &W1 Stores the active profile as Profile 1 Disable auto-retrain Enable auto-retrain Displays the current Select Modulation settings...
Page 85
Attention Switzerland User: If your Swisscom phone line does not have Taxsignal switched OFF, modem function may be impaired. The impairment may be resolved by a filter with the following specifications: Telekom PTT SCR-BE Taximpulssperrfilter-12kHz PTT Art. 444.112.7 Bakom 93.0291.Z.N Appendix A.
Macrovision Corporation. Reverse engineering or disassembly is prohibited. Trademarks The following terms are trademarks of Lenovo in the United States, other countries, or both: Lenovo Rescue and Recovery...