Makita LS0815F Instruction Manual
Slide compound miter saw
Hide thumbs
Also See for LS0815F:
- Instruction manual (156 pages) ,
- Instruction manual (137 pages) ,
- Instruction manual (109 pages)
Related Manuals for Makita LS0815F
Summary of Contents for Makita LS0815F
- Page 1 INSTRUCTION MANUAL Slide Compound Miter Saw LS0815F LS0815FL LS0815FL GBA 014594 DOUBLE INSULATION IMPORTANT: Read Before Using.
-
Page 2: Table Of Contents
50 mm x 215 mm 65 mm x 215 mm 60° (right) 65 mm x 150 mm LS0815F / LS0815FL ･･･ 220 - 240 V, 50-60 Hz Rated voltage LS0815FL GBA ･･･ 110 V, 50 Hz Rated input 1,400 w, S6 40% 5 min... - Page 3 Electronic Equipment and its implementation in EC Declaration of Conformity accordance with national law, electric Makita declares that the following Machine(s): equipment that have reached the end of Designation of Machine: their life must be collected separately Slide Compound Miter Saw and returned to an environmentally Model No./ Type:...
-
Page 4: Additional Safety Rules For Tool
Guard against electric shock. 16. Remove adjusting keys and wrenches. Avoid body contact with earthed or grounded Form the habit of checking to see that keys and surfaces (e.g. pipes, radiators, ranges, adjusting wrenches are removed from the tool refrigerators). before turning it on. - Page 5 Do not perform any operation freehand. The lulled into a false sense of security. Blades workpiece must be secured firmly against the turn are extremely unforgiving. base and guide fence with the vise during all 26. Always use accessories recommended in this operations.
-
Page 6: Installation
FUNCTIONAL DESCRIPTION INSTALLATION Bench mounting WARNING: Always be sure that the tool is switched off 1. Stopper pin • and unplugged before adjusting or checking function on the tool. Failure to switch off and unplug the tool may result in serious personal injury from accidental start-up. -
Page 7: Positioning Kerf Board
If guard becomes damaged through age or UV light Unplug the tool before any adjustment is attempted. When exposure, contact a Makita service center for a new installing a new blade, always check the lower limit position guard. DO NOT DEFEAT OR REMOVE GUARD. -
Page 8: Adjusting The Miter Angle
To adjust the bevel angle, loosen the lever at the rear of Stopper arm the tool counterclockwise. Unlock the arm by pushing the handle somewhat strongly in the direction that you 1. Stopper arm intend to tilt the saw blade. 2. - Page 9 • result in unintentional operation and serious see that the switch trigger actuates properly personal injury. Return tool to a Makita service and returns to the "OFF" position when center for proper repairs BEFORE further usage. released. Do not pull the switch trigger hard NEVER defeat the lock-off button by taping down •...
-
Page 10: Assembly
1. Switch for laser NOTE: When laser line is dim and almost or entirely • invisible because of the direct sunlight in the indoor or outdoor window-by work, relocate the work area to a place not exposed to the direct sunlight. - Page 11 Accidental start up of the tool may the blade. If the flange is installed incorrectly the result in serious personal injury. flange will rub against the machine. Use only the Makita socket wrench provided to • WARNING: install or remove the blade. Failure to use the...
-
Page 12: Securing Workpiece
For all countries other than European countries When the dust bag is about half full, remove the dust bag from the tool and pull the fastener out. Empty the 1. Hex bolt dust bag of its contents, tapping it lightly so as to (left-handed) remove particles adhering to the insides which might 2. -
Page 13: Operation
tool contacts the vise when lowering the handle fully WARNING: and pulling or pushing the carriage all the way. If some Before operating the tool, make sure that the • part contacts the vise, re-position the vise. sliding fence is secured firmly. Press the workpiece flat against the guide fence and the Before bevel-cutting, make sure that no part of •... - Page 14 During a slide cut, gently push the carriage toward the • Slide (push) cutting (cutting wide workpieces) guide fence without stopping. If the carriage movement is stopped during the cut, a mark will be left in the workpiece and the precision of the cut will be impaired. WARNING: Make sure the blade is not contacting the •...
- Page 15 NOTICE: Miter cutting When pressing down the handle, apply pressure in • Refer to the previously covered "Adjusting the parallel with the blade. If a force is applied miter angle". perpendicularly to the turn base or if the pressure direction is changed during a cut, the precision of Bevel cut the cut will be impaired.
-
Page 16: Measuring
with its CEILING CONTACT EDGE 1. Inside corner against the guide fence on the saw. 2. Outside corner The finished piece to be used will • always be on the LEFT side of the blade after the cut has been made. Cutting aluminum extrusion 1. -
Page 17: Maintenance
interfere with the positioning of the material Carrying tool being cut. Misalignment of the material being cut can case unexpected movement during the cutting operation which may result in a loss of control and serious personal injury. NOTICE: When the wood facing is attached, do not turn the •... -
Page 18: Adjusting The Cutting Angle
NOTICE: 1. Screw Never use gasoline, benzine, thinner, alcohol or • 2. Pointer the like. Discoloration, deformation or cracks may 3. Miter scale result. Adjusting the cutting angle This tool is carefully adjusted and aligned at the factory, but rough handling may have affected the alignment. If your tool is not aligned properly, perform the following: Miter angle 014277... -
Page 19: Replacing Carbon Brushes
To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized Service Centers, always using Makita replacement parts. 014296 Adjust the 45° bevel angle only after performing 0° bevel angle adjustment. To adjust left 45°... -
Page 20: Optional Accessories
Misuse of an accessory or attachment may result in serious personal injury. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center. Steel & Carbide-tipped saw blades • Miter saw blades For smooth and precise cutting in various materials. - Page 24 Makita Jan-Baptist Vinkstraat 2, 3070, Belgium Makita Corporation Anjo, Aichi, Japan www.makita.com JM23580023...
Need help?
Do you have a question about the LS0815F and is the answer not in the manual?
Questions and answers