Advertisement
Advertisement
Table of Contents
Related Manuals for Ritelite K9 30 LED
Summary of Contents for Ritelite K9 30 LED
- Page 1 PORTABLE WORKLIGHT Operating Instructions Thank you for purchasing the Ritelite K9 30 LED. This product design represents the latest technology in LED portable lighting and is designed to be virtually maintenance free and robust enough to deal with the rigours of a harsh work environment.
-
Page 2: Operation Quick Start
Your K9 30 LED can be charged and run at the same time, this may be useful when using the light as an emergency back up should the mains power fail. - Page 3 USING YOUR K9 30 LED The K9 30 LED can be set up in two basic modes. Torch mode allows the user to carry the unit with the extension arm and head folded down and locked in position. Torch Mode...
-
Page 4: Battery Status
OPERATION - ADVANCED FEATURES To use the unit simply press the on button and the light will come on to 100% power/brightness and is ready for use. The additional buttons listed below allow other features to be accessed. Battery Status fig 1 - Controls (Button 1) = ON/OFF (Button 2) = MODE - Flashing, SOS, Alternate flashing (between inner and outer LED arrays). -
Page 5: Flashing Mode
LED’s to be run. Battery Status Indication A low battery warning with cut-off function is included with your K9 30 LED to help prevent deep discharging the high performance cyclic SLA battery. Deep discharging can lead to reduced battery performance and life. Note this isn’t a failsafe to prevent damage, the battery must be recharged after use within 24 hours regardless of how long it has been run. - Page 6 falls to a point where the unit will automatically switch off. This process will give users adequate time to retreat to an area of safety without being left in the dark. The light should not be switched back on until the battery has been recharged to prevent deep discharge and possible irreversible damage to the battery.
-
Page 7: Optional Equipment
High impact engineering polymers combined with stainless steel fittings ensure the K9 30 LED is impervious to everyday knocks and bangs. The K9 30 LED employs an internal steel chassis to retain the battery. This construction makes the K9 30 LED a very strong robust unit, giving reliability throughout the K9 30 LED’s life. - Page 8 K9 30 LED. Once the alternator stops charging the vehicle battery, the K9 30 LED charger will continue till end of charge or until it sees the voltage of the primary supplying battery fall to a point. It then terminates charge to the K9 30 LED to prevent further discharge which could cause the vehicle not to start.
-
Page 9: Maintenance
Is charger plug inserted all the way? Make sure plug is inserted fully and locking ring turned clockwise. b) Has battery been left completely flat for an extended period of time? Contact Ritelite (Systems) Ltd on 01780 758585 for technical assistance or e-mail sales@ritelite.co.uk. - Page 10 5. THE INTERNAL (VEPAC) CHARGER LED SHOWS A RAPIDLY FLASHING AMBER This is a fault indication, the charger has timed out after 18 hours because it can’t recharge the battery – replace K9 30 LED battery with the approved type – SLK930SB replacement intelligent SLA battery. CONFORMANCE CE Marked.
-
Page 11: Technical Data
K9-30/VP VEPAC vehicle charger: Input 12V-30V DC 5A, Output 12V 4A K9-30/POLE Max. 4 x poles can be stored directly in the base of the K9 30 LED = 1800mm working height K9-30/HND MESH remote control: Maximum range 100m in open space... - Page 12 Patents Pending GB 0922370.2 - PCT/GB2010/001619 CAUTION • Always read the manual fully before use. • Use the Ritelite approved chargers only, other chargers may cause a detrimental effect on the performance of this unit. • Ensure adequate ventilation for this unit whilst charging.
Need help?
Do you have a question about the K9 30 LED and is the answer not in the manual?
Questions and answers