Warnings Safeguarding the environment Instructions for installation and use Extraction modes Installation Hood description Functioning Maintenance After-Sales Service...
Warnings • This appliance should not be used by children or people with limited physical or mental abilities and with no experience or knowledge of its use, unless they are supervised by someone in charge of their safety or who has taught them how to use the appliance. •...
Warnings Declaration of conformity This product has been designed, manufactured and marketed according to the following: - safety objectives of the “Low Voltage” Directive 2006/95/CE (which replaces 73/23/CEE and subsequent amendments). - protection requirements of “EMC” Directive 89/336/EEC amended by Directive 93/68/EEC. Troubleshooting guide Hood does not work: •...
Instructions for installation and use This is an excessively heavy product and the movement and installation of the hood should be done by at least two or more people. Follow the instructions in this manual carefully. The manufacturer denies all responsibility for damage or fire to the appliance resulting in failure to comply with the instructions in this manual.
Installation The hood comes with plugs suitable for most • Furthermore, check that near the area where walls/ceilings. You should however consult a you are installing the hood (in an area accessible qualified technician to make sure the installation is even when the hood is fitted) there is an suitable for your kind of wall/ceiling.
Page 8
Installation Fig. 4 • Recirculation mode only: fix the deflector to the c. Connect a suitable extraction pipe to the frame: connection ring provided. It should be long a. Insert the deflector from one side of the enough ( with a diameter of 150mm) to reach frame so that the rectangular hole at the centre the connection ring on the motor unit when it is is facing downwards.
Page 9
Installation Fig. 5 Fig. 6 • Attach the ceiling perforation layout onto the • Remove the power cable from the connection ceiling (the centre of the layout should box on the motor unit. correspond with the centre of the hob and the •...
Page 10
Installation Fig. 7 Fig. 9 • Hook the frame to the 2 screws on the ceiling • Hook the motor unit onto the frame on 4 and fit securely with another 2 screws (front screws previously screwed onto the unit. and back).
Page 12
Installation Fig. 10 Fig. 11 • Insert the lower chimney flue onto the motor • Hook the hood onto the motor unit using the 4 unit (check that the re-edged side is facing screws previously screwed onto the unit and upwards) and to keep it temporarily in position, the hook slots on the hood.
Page 13
Installation Fig. 12 Fig. 13 • Connect the electricity to the lamps and control • Install the two upper covers using 2 screws for panel. each cover. • Remove the temporary support rods holding up the lower flue and lower the flue gently. •...
Hood description Fig. 14 1. Control panel 2. Grease filter 3. Handle for unhooking the grease filter 4. Halogen bulbs 5. Steam deflector screen 6. Chimney 7. Air outlet (only for use with recirculation version) 8. Panel Functioning Turn to maximum speed when there is a lot of steam in the kitchen. For maximum effect we suggest you to start extraction for 5 minutes before starting to cook and leave it running after you have finished cooking for about another 15 minutes.
Maintenance Always disconnect the power supply before carrying out any kind of maintenance work. Cleaning The hood should be cleaned regularly both inside and out (at least as often as you carry out maintenance on the grease filters). Use a damp cloth with mild cleaning products. Avoid using harsh products.
Page 16
Maintenance Carbon filter (Recirculation mode only) Fig. 17 The filter absorbs the unpleasant smells produced when cooking. The carbon filter can be washed every two months in hot water with suitable cleaning fluids, or in the dishwasher at 65°C (when washing in the dishwasher, do a full wash without any plates inside).
After-Sales Service Before calling Customer Care Centre: 1. See if you can solve the problem yourself with the help of the “Troubleshooting guide”. 2. Switch off the hood for a few minutes and re- start it to see if the problem has cleared itself. 3.
Socket outlet / plug (valid for both countries) If the fitted plug is not suitable for your socket outlet, please contact KitchenAid Service for further instruction. Please do not attempt to change plug yourself. This procedure needs to be carried out by a qualified technician in compliance with the manufactures instructions and current standard safety regulations.