Advertisement
Quick Links
MIDI Solutions Pedal Controller
Operating Instructions M316
c 2002 MIDI Solutions, Inc.
All Rights Reserved
Printed in Canada
MIDI Solutions, Inc.
P.O. Box 3010
Vancouver, BC V6B 3X5
www.midisolutions.com
6
TM
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
PROGRAMMING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
MIDI CHANNEL TABLE . . . . . . . . . . . . . . . . . . . . . . . 23
MIDI CONTROL CHANGE TABLE . . . . . . . . . . . . . . . 24
HEXADECIMAL CONVERSION TABLE . . . . . . . . . . . 27
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
.
Congratulations on your purchase of the MIDI Solutions
Pedal Controller. The MIDI Solutions Pedal Controller provides a
1/4" stereo phone jack input for connection to a pedal or other
variable resistance that can be used to control the value of a
selected MIDI parameter in real time. The generated MIDI data is
merged with incoming MIDI data and sent to the the output of the
Pedal Controller. Programmed settings of the Pedal Controller are
retained in non-volatile memory until cleared or overwritten with
new settings. The Pedal Controller is MIDI-powered and requires
no batteries or power supply to operate.
To program the Pedal Controller, connect the In of the Pedal
Controller to the MIDI Out of the device that is sending the
programming commands. Connect a pedal into the 1/4" stereo
phone jack pedal input (Ped). The Out jack can be left
disconnected during programming. Once the Pedal Controller is
programmed, it can be inserted anywhere in your MIDI setup.
Connect the MIDI Out or Thru of the sending MIDI device to the In
of the Pedal Controller, the pedal to the pedal input (Ped), and the
Out of the Pedal Controller to the MIDI In of the receiving MIDI
device. The number of MIDI Solutions products connected
between any two MIDI devices should be limited to five.
3
5
Advertisement
Related Manuals for Midi Solutions Pedal Controller
Summary of Contents for Midi Solutions Pedal Controller
- Page 1 Connect the MIDI Out or Thru of the sending MIDI device to the In of the Pedal Controller, the pedal to the pedal input (Ped), and the Out of the Pedal Controller to the MIDI In of the receiving MIDI device.
- Page 2 1/3 of the maximum pedal resistance. If using a footswitch, set the Neutral Range Top and Neutral Range Bottom parameters to 127 (=7F Hex). This will ensure that the Pedal Controller transmit s only the preprogrammed minimum and maximum values.
- Page 3 F0 00 00 50 16 01 03 04 00 09 7F F7 F0 22 33 44 55 F7 Dump Settings To dump all of the Pedal Controller’s current settings, send it the following System Exclusive message: F0 00 00 50 16 10 F7 (all values in Hexadecimal) Upon receipt of this message the Pedal Controller will dump its current settings the MIDI Out port.
- Page 4 If the product requires service, a Return Merchandise Authorization (RMA) number must be obtained from MIDI Solutions and the product must be shipped prepaid to a specified Service Center. MIDI Solutions will repair or replace the product at our discretion and will pay return shipping fees.
Need help?
Do you have a question about the Pedal Controller and is the answer not in the manual?
Questions and answers