Subscribe to Our Youtube Channel
Summary of Contents for Always On GES-701N
- Page 1 GES-N-Series Operators Manual GES-701N – GES-302N On Line: 700VA, 1kVA, 1.5kVA, 2kVA, 3kVA Dual Conversion On-Line UPS Single-Phase Input, Single-Phase Output Version 2.12...
- Page 2 THIS PAGE IS INTENTIONALLY BLANK...
- Page 3 Systems Inc. Any electrical or mechanical modifications to this equipment, without prior written consent of Always On UPS Systems Inc, will void all warranties and may void UL/cUL/CSA listing. Unauthorized modifications also can result in personal injury, death, or destruction or the equipment.
- Page 4 Always On UPS Systems IMPORTANT SAFETY INSTRUCTIONS • THIS MANUAL CONTAINS IMPORTANT INSTRUCTIONS THAT SHOULD BE FOLLOWED DURING INSTALLATION AND MAINTENANCE OF THE UPS AND BATTERIES. • THE UPS SYSTEM IS NOT INTENDED FOR EXTERNAL USE UNLESS SPECIFICALLY DESIGNED FOR IT.
- Page 5 Always On UPS Systems MORE SAFETY INSTRUCTIONS • DO NOT USE THIS EQUIPMENT FOR ANY PURPOSE OTHER THAN THE INTENDED USE. • EXAMINE THE PACKAGING CONTAINER FOR DAMAGE. NOTIFY THE CARRIER IMMEDIATELY IF DAMAGE IS PRESENT. • DO NOT DISASSEMBLE THE UPS.
-
Page 6: Table Of Contents
Always On UPS Systems Table of Contents INTRODUCTION ..................2 1.1......................2 ODES OF PERATION PRODUCT DESCRIPTION ..............3 2.1......................3 HEORY OF PERATION 2.2........................3 LOCK IAGRAM 2.3..................... 4 ESCRIPTION OF LOCK 2.4........................ 5... -
Page 7: Introduction
Always On UPS Systems Introduction Congratulations on your choice of the Always On N Series On-Line Uninterruptible Power System (UPS). The N Series features the very latest, top of the line, microprocessor technology and IGBT transistors for clean, highly regulated, PWM (Pulse Width Modulated) True Sine Wave power. -
Page 8: Product Description
Always On UPS Systems Product Description 2.1. Theory of Operation The UPS (Uninterruptible Power Supply) is designed to be installed between utility (commercial supplied power) and your loads. It is used to protect your loads from noticing any power fluctuations (eg. Blackouts, brownouts, over- voltage conditions). -
Page 9: Description Of Each Block
Always On UPS Systems 2.3. Description of Each Block Input Breaker: Prevents the breaker of the distribution panel from tripping when a UPS fault or over-current condition occurs. EMI/RFI Filter: This filter attenuates the electrical noise associated with the polluted utility power to the UPS or noise (THD) generated by the UPS. -
Page 10: Special Features
Always On UPS Systems 2.4. Special Features Efficiency Optimizer function The Efficiency Optimizer function adds cost effectiveness, minimizes power loss and reduces power consumption. Alternating between bypass and on- line modes is achieved automatically and in accordance with the conditions of the utility AC power. -
Page 11: Handling
In the event that physical damage is visible, the carrier must be informed immediately and a claim filed with them. Inform Always On as soon as the claim has been filed and a copy of claim should be faxed to Always On at (250) 491-9775. -
Page 12: Installation
Always On UPS Systems Installation The UPS is intended for installation in a temperature-controlled indoor area, free of conductive contaminants. Installation should be conducted by qualified individuals. 4.1. Location The N Series UPS is intended for installation in a temperature and humidity controlled indoor environment, free of conductive contaminants with unrestricted airflow. -
Page 13: Electrical Considerations
Always On UPS Systems 4.2. Electrical Considerations The UPS shall be installed by a qualified technician and wired in accordance with local and national electrical codes. The following information is for recommendation only. Standard Load VA Rating F (Hz) Panel... - Page 14 Always On UPS Systems Interface (optional) RS232/Dry Contact Inerface Network Transient Protector External Battery (optional) Circuit Breaker Outlet Circuit Breaker Input Figure 4.3.3 Rear view of the 2 and 3kVA 120VAC UPS Interface (optional) RS232/Dry Contact Inerface Network Transient Protector...
-
Page 15: Input, Output And External Battery Connection
Always On UPS Systems 4.4. Input, Output and External Battery Connection The 700VA, 1,000VA and 1,500VA (701N, 102N and 152N) come with a 6’ cord, complete with a 5-15P connection that will plug into a regular wall receptacle (Figure 4.4.1). -
Page 16: Start-Up/Shutdown
Always On UPS Systems Start-up/Shutdown Once the UPS is installed, make sure it is located on a sturdy, well-ventilated surface, and that the exhaust fans and ventilation grills are not obstructed. Below is the necessary information for operation of the unit. Normally the UPS runs automatically, but on those few occasions such as just after installation start-up or shutdown procedures maybe required. -
Page 17: Front Control Panel
Always On UPS Systems Front Control Panel Figure 6.1 LCD Display 6.1. Normal Display The UPS status is shown in normal display mode. From here you have a choice to go to UPS meters display and the Settings display by pushing the button. -
Page 18: Button Operation
Always On UPS Systems 6.3. Button Operation Please note the three operating buttons on the front panel: “ON/ OFF” button: (a) Push the “ON/OFF” button for at least 3 seconds to turn on the UPS. (b) When UPS is working, push the “ON/OFF” button for at least 3 seconds to turn off the UPS. - Page 19 Always On UPS Systems To enter configuration mode, press and hold the “FUNC” button for one second. The first configuration parameter will be shown on the LCD display. Press the “FUNC” button to scroll through the parameters. Press the “ENTER” button to select the parameter.
- Page 20 Always On UPS Systems Settings LCD Display Explanation Selection Factory Default Output Voltage Select nominal output 100/110/115/120/127VAC 120VAC O/P V Setting Setting voltage 208/220/230/240VAC 220VAC ±2% Select input frequency ±5% ±5% Input Frequency I/P F Setting range when UPS goes into free run mode ±7%...
-
Page 21: Audible Alarm
Always On UPS Systems Audible Alarm 7.1. Backup mode The UPS will beep once every five (5) seconds and the BACKUP LED will light, when the unit is in back-up mode. (beep - - - - beep - - - - beep) [Slow beep] 7.2. -
Page 22: Battery Replacement
Always On UPS Systems 10. Battery Replacement The batteries may be replaced without having to turn the UPS off or disconnecting the load due to the hot-swappable battery feature. When replacing batteries, use the same number and the following types of batteries:... -
Page 23: Software Setup For Standard Software Applications
Always On UPS Systems 11. Software Setup For Standard Software Applications At the back of the UPS is an interface allowing direct communication with your computer system, the location of which can be found in figure 4.3.1-4. There is a RS232 serial data interface, one USB data interface and an emergency power off switch supplied. -
Page 24: Epo Port (Emergency Power Off)
Always On UPS Systems 11.4. EPO port (Emergency Power Off) A customer-supplied switch located remotely can be used to open the EPO connection and allows UPS output receptacles to be switched off. Since the EPO shuts down the equipment immediately, orderly shutdown procedures are not followed by the power management software. -
Page 25: Optional Extras
Always On UPS Systems 12. Optional Extras 12.1. Procedure for (Optional) Extended Battery Cabinets Attention: Choose the correct battery pack voltage, according to the UPS rated capacity. Do not connect too few or too many batteries, as this could cause electrical shock, damage or death. -
Page 26: Snmp (Network Management) Adapter (Optional)
Connect the UPS to the AC supply and turn “On” the UPS. 12.2. SNMP (Network Management) Adapter (Optional) The Always On Simple Network Management Protocol (SNMP) adapter is a web-based management product that uses multiple, open standards such as Telnet, HTTP, and SNMP to provide full management of supported devices. -
Page 27: As-400 And Relay Contact (Optional)
Always On UPS Systems 12.3. AS-400 and Relay Contact (Optional) Located on the rear panel of the UPS is a connector, which provides status information through relay and photo-coupler of the UPS operation. Pin Assignment (DB 25pin male connector) Input signal pin assignment: Remote Emergency Power Off: Pin 24, 25 When pin 24 and pin 25 are shorted, the UPS will power off immediately. - Page 28 Always On UPS Systems State 9,10 11,12 Normal Open Close Open Close Open Open Closed Fault Close Open Closed Open On Battery Open Close Close Open Open Closed Battery Low Open Close Close Open Close Open Closed On Bypass Closed...
-
Page 29: Troubleshooting
Always On UPS Systems 13. TROUBLESHOOTING The following chart of unusual situations includes some possible problems and solutions occurring under daily operation. If the UPS loses its basic functions, please check the following items before contacting your local dealer or service center:... -
Page 30: Technical Data
Always On UPS Systems 14. TECHNICAL DATA Standard Models N-SERIES MODEL NO. GES-701N GES-102N GES-152N GES-202N GES-302N Maximum Capacity 700VA/490W 1000VA/700W 1500VA/1050W 2000VA/1400W 3000VA/2100W GENERAL UPC Order Code 825433 30100 825433 30200 825433 30300 825433 30400 825433 30500 Nominal Voltage... -
Page 31: Contact Information
Always On UPS Systems 15. CONTACT INFORMATION 15.1. Additional Purchases or Upgrades Always On UPS Systems Inc. Bldg 1 – 150 Campion Road, Kelowna, BC, Canada, V1X 7S8 Phone: (250) 491-9777 Ext 451 Fax: (250) 491-9775 Email: sales@alwaysonups.com Website: www.alwaysonups.com 15.2.
Need help?
Do you have a question about the GES-701N and is the answer not in the manual?
Questions and answers