Sea Recovery Aqua Mini 170 Owner's Manual
  1. Manuals
  2. Brands
  3. Sea Recovery Manuals
  4. Water Filtration Systems
  5. Aqua Mini 170
  6. Owner's manual

Sea Recovery Aqua Mini 170 Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Aqua Whisper Mini 170-750
Owner's Manual
Revision B - February 2014
B651220001B
Manual PN
| Revision: 02/25/2014

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Aqua Mini 170 and is the answer not in the manual?

Questions and answers

Related Manuals for Sea Recovery Aqua Mini 170

Summary of Contents for Sea Recovery Aqua Mini 170

  • Page 1 Aqua Whisper Mini 170-750 Owner’s Manual Revision B - February 2014 B651220001B Manual PN | Revision: 02/25/2014...
  • Page 3 Sea Recovery Aqua Mini 170, 350, 550 and 750 Owner's Manual Sea Recovery Corp. Manual PN B651220001B...

  • Page 5: Table Of Contents

    Recommended Power Wire Size to Booster Pump............................20 Chapter 3: System and Components Description...............21 Packing List........................................21 Component Descriptions....................................21 Prefiltration Subsystem....................................21 Aqua Mini 170,350,550,&750 PandID (Piping and Interconnect Diagram)......................23 Pressurization Subsystem....................................23 Brine Discharge Subsystem.....................................23 Product Water Subsystem....................................24 Fresh Water Flush Subsystem..................................24 Electronic Subsystem......................................24 Chapter 4: System Installation Precautions and Information..........27...
  • Page 6 Installation Procedure.....................................34 System Commissioning....................................36 Start-up Procedure of a New Aqua Mini 170, 350, 550 & 750..........................38 Chapter 5: System Operation.....................41 System Operation Notes....................................41 Operation Cautions......................................41 Startup Procedure......................................41 High/Low Pressure Fault Lamp Explanation..............................42 Sea Recovery Mini Controller Operations................................43 Display Menu.........................................43 Configuration (Change) Menu..................................44 Configuration (Read) Menu....................................44...
  • Page 7 Chapter 10: System Logs....................89 Sea Recovery Aqua Mini 170,350,550,&750 NEW SYSTEM INITIAL READINGS....................89 Sea Recovery AquaMini 170,350,550,& 750 System Identification Information....................91 Sea Recovery Aqua Mini 170,350,550, & 750 Daily Operation Log System Readings..................92 Chapter 11: Glossary......................93 Terms..........................................93 Chapter 12: Exploded Parts View..................95 A041C AQUA MINI 170....................................96...
  • Page 8 HP HOSE ASSEMBLY....................................154 AVAILABLE TUBES AND FITTINGS..................................155 TUBE COMPRESSION FITTINGS REPLACEMENT PARTS..........................158 Clean/Rinse Inlet Valve....................................159 Chapter 13: Appendix.......................161 ABS Certificate of Design Assessment................................162 FCC Compliance......................................163 European Conformite Europene (CE)................................164 Sea Recovery Aqua Mini 170, 350, 550 and 750...

  • Page 9: Preface: About This Manual

    The information contained in the manual is distributed on an “as is” basis, without warranty. While every effort has been taken in the preparation of this manual, Sea Recovery Corporation shall not be held liable with respect to any liability, loss or damage caused by the instructions contained in this manual. The information contained in this...

  • Page 10: Trademarks

    Sea Recovery’s trademarked name or Sea Recovery’s trademarked logo mark are not to be used in any form or manner except with Sea Recovery Corporation’s written permission. Sea Recovery Corporation holds all rights to its copyrights and trademarks, and to the material contained in this manual. Any use of such requires the written permission from Sea Recovery Corporation.
  • Page 11 About this Manual Date Affected Page Descriptions October 22, 2010 Section 9, Page 25 Updated New Fresh Water Flush August 1, 2011 Section 9 Updated HP Pump, and Vessel Drawings - New 550and750 January 2014 Entire Manual Revised and reorganized all topics within manual...

  • Page 13: Chapter 1: Introduction

    Sea Recovery warrants that the Aqua Matic RO Desalination System performs according to specifications for a period of 12 months from the date of shipment. Sea Recovery’s liability under this warranty is limited to repair or replacement of the Aqua Matic RO Desalination System at Sea Recovery Corporation’s discretion. Under no circumstances is Sea Recovery Corporation liable for consequential damages arising out of or in any way connected with the failure of the system to perform as set forth herein.

  • Page 14: Cleaning

    In the event of a defect, a malfunction, or failure specifically covered by this warranty and during the warranty period, Sea Recovery Corporation will repair or replace, at its option, the product or component therein which upon examination by Sea Recovery Corporation appears to be defective.

  • Page 15: Safety

    If System disposal is necessary, you must comply with all federal and state environmental regulations. Compliance • Sea Recovery’s Reverse Osmosis Desalination Systems are Type Accepted by the American Bureau of Shipping, ABS. • Sea Recovery’s Reverse Osmosis Desalination Systems comply with FCC § 15.105 •...

  • Page 16: Chemical Warnings

    CONTACT IMMEDIATELY FLUSH EYES WITH WATER FOR 15 MINUTES & GET IMMEDIATE MEDICAL ATTENTION. THOROUGHLY WASH AFFECTED SKIN AFTER HANDLING PRODUCT. MEDICAL PERSONNEL FAMILIAR WITH Sea Recovery “SRC SC”, SYSTEM & MEMBRANE STORAGE CHEMICAL, ARE AVAILABLE 24 HOURS A DAY, 7 DAYS A WEEK, U.S.A. TOLL FREE MEDICAL EMERGENCY NUMBER: 1-800-228-5635.

  • Page 17: Patent Information

    ATTENTION. THOROUGHLY WASH AFFECTED SKIN AFTER HANDLING PRODUCT. CONTACT A PHYSICIAN IF IRRITATION PERSISTS. MEDICAL PERSONNEL FAMILIAR WITH Sea Recovery “SRC MCC3”, R.O. MEMBRANE ELEMENT RUST REMOVER CLEANING CHEMICAL, ARE AVAILABLE 24 HOURS A DAY, 7 DAYS A WEEK, U.S.A. TOLL FREE MEDICAL EMERGENCY NUMBER: 1-800-228-5635.

  • Page 19: Chapter 2: Specifications

    ( +-15% at 850 psig / 56 BAR, 77°F / 25°C and 35,000 PPM TDS Feed Water Salinity ) Model Number per 1 hour of operation: per 24 hours of operation: SRC Aqua Mini 170 7 U.S. Gallons / 26.8 liters 170 U.S. Gallons / 644 liters SRC Aqua Mini 350 14.6 U.S.

  • Page 20: Electrical Motor Specifications

    19.68 in / 50 cm 15.78 in / 40 EXTERNAL INSTALLATION WATER CONNECTIONS Pipe sizes to be supplied by the installer for connection of the Sea Recovery supplied components Aqua Mini 170 Feed Inlet: 5/8” MNPT Male National Pipe Thread Standard Brine Discharge 1/2”...

  • Page 21: Recommended Power Wire Size To System

    110 - 115 220 - 230 220 - 230 DIRECT CURRENT SYSTEMS Aqua Mini 170 only (SRC SF 350 is not available in Direct Current [DC]) RECOMMENDED CIRCUIT BREAKER AMPERAGE RATING Aqua Mini 170 Aqua Mini 350, 550, & 750...

  • Page 22: Recommended Power Wire Size To Booster Pump

    14 AWG / 2 mm2 14 AWG / 2 mm2 12 AWG / 3 mm2 230 VAC 3 Ampere 14 AWG / 2 mm2 14 AWG / 2 mm2 14 AWG / 2 mm2 Sea Recovery Aqua Mini 170, 350, 550 and 750...

  • Page 23: Chapter 3: System And Components Description

    Component Descriptions All components supplied by Sea Recovery, both standard and optional, are described in this section along with items required or desired by the installer. The location, operation, and purpose of each major component are briefly explained in this section.
  • Page 24 6. Pre-Filter This filter removes suspended solids 5 Microns and larger to protect the Reverse Osmosis Membrane from fouling. Caution: Do not use third party prefilter elements, use only Sea Recovery prefilter elements. Third party prefilter elements do not properly fit and the seams fall apart. They also allow by-pass resulting in premature fouling of the RO Membrane Element.

  • Page 25: Aqua Mini 170,350,550,&750 Pandid (Piping And Interconnect Diagram)

    System and Components Description Aqua Mini 170,350,550,&750 PandID (Piping and Interconnect Diagram) Pressurization Subsystem Proper pressure and proper flow across the Membrane Element are two basic requirements of Reverse Osmosis. 1. High Pressure Pump Motor is directly coupled to the High Pressure Pump.

  • Page 26: Product Water Subsystem

    This subsystem measures water quality, controls the direction of Product Water flow, Starts and Stops the pumps, and contains the central electrical connection point of the system. It also ensures only potable Product Water passes into the Product Water Storage Tank. Sea Recovery Aqua Mini 170, 350, 550 and 750...
  • Page 27 System and Components Description 1. Salinity Controller The controller monitors the salt content of the product water and signals the 3-Way Product Diversion Valve when Potable Water is being produced. The 3-Way Product Diversion Valve, Motors, Remote Control, and UV Sterilizer are each governed by this controller. This enclosure houses the high-voltage components of the system.

  • Page 29: Chapter 4: System Installation Precautions And Information

    Chapter System Installation Precautions and Information Special Considerations 1. Length of Connection Lines: • All connection lines should be as short and straight as possible using minimum fittings. Increased length causes line-loss in the Feed Water line. Increased length causes excessive pressure build up in the Brine Discharge line. Increased length causes excessive pressure build up in the Product Water line.

  • Page 30: Installation Cautions

    System to the ship’s potable water system if the system contains chlorinated or brominated water. These chemicals destroy the copolymer components within the system. These oxidants and others also damage the R.O. Membrane Element. The Sea Recovery Optional Fresh Water Flush Accessory removes chlorine and bromine from the ship’s potable water system.

  • Page 31: High Pressure Pump Preparation

    2. Ensure that the pump oil level is even with or higher than the center of the pump sight glass. Damage to the High Pressure Pump will occur if the wrong oil is used in its crankcase. Use only Sea Recovery supplied pump oil.

  • Page 32: System And Component Mounting

    System and Component Mounting The following steps discuss the installation of the Aqua Mini 170, 350, 550 & 750. The prior illustrations show the system installed in the port-aft section of a boat as an example. It is understood that this location or configuration may not always be possible, and there are a variety of locations the system may be mounted.

  • Page 33: Plumbing Connections

    System Installation Precautions and Information 3. Mount the Fresh Water Flush Check Valve Assembly vertically in close proximity to the Booster Pump, Fresh Water Flush Filter Canister, and the Pre-Filter. 4. The Booster Pump is mounted to a flat surface using the 4 supplied #10 x 1 1/4” long Type "A" screws. The Booster Pump is mounted below water level to assist priming, and in an accessible location to allow access for maintenance.

  • Page 34: Tube Fitting Connections Assembly [24]

    Check to ensure that the O-Ring is seated onto the tube under the spacer (and not pinched into the body). Insert tube with attached parts into the body and tighten nut finger tight. Sea Recovery Aqua Mini 170, 350, 550 and 750...

  • Page 35: Uv Light Installation

    System Installation Precautions and Information TUBING "O" RING GRAB RING SPACER 4. Connect Brine Discharge line with the supplied 20 feet (6 meters) of 3/8” (9.5 mm) O.D. Brine Discharge Tubing (refer to illustrations on the following page): Outlet of Inlet of System Brine Discharge Discharge 3-way Clean/Rinse Valve [31]...

  • Page 36: Plumbing Requirements

    4. Remove temporary pipe and insert the return pipe into the cylinder port and label the port “Outlet”. 5. Slowly pressurize the UV unit by filling the cylinder with water while checking for leaks. Sea Recovery Aqua Mini 170, 350, 550 and 750...
  • Page 37 System Installation Precautions and Information 6. If leaks are found on the compression nuts, depressurize the unit and slightly tighten the leaking compression nut. 7. Retest until a leak-free installation is verified. 8. Once UV unit is leak-free, the quartz sleeve installation is complete and the UV lamp can be installed. Note: To remove tube from fitting, first remove the C-clamp then push fitting sleeve down.

  • Page 38: System Commissioning

    System Commissioning INITIAL START-UP PROCEDURE OF A NEW Aqua Mini 170/350/550/750: The Commissioning instructions must be carried out for initial start-up of a NEW system. Failure to follow these instructions exactly leads to system failure and causes damage to the components. Read this section and other appropriate sections of the manual in order to gain familiarity with the requirements of the system and functions of each component.
  • Page 39 System Installation Precautions and Information...

  • Page 40: Start-Up Procedure Of A New Aqua Mini 170, 350, 550 & 750

    Start-up Procedure of a New Aqua Mini 170, 350, 550 & 750 1. Ensure that the installation has been properly performed as per the instructions in this section. 2. Ensure that the shipping tape from the High Pressure Pump Oil Fill Cap has been removed to expose the Oil Fill Cap air breather hole.
  • Page 41 12. Open the Back Pressure Regulator Valve [17] FULLY OPEN by turning counter clockwise. Caution: The Back Pressure Regulator Valve [17] must be fully open when starting the Aqua Mini 170 - 750. If this valve is left closed, it will cause damage to the system.
  • Page 42 WHILE ADJUSTING THE BACK PRESSURE REGULATOR TO OPERATING PRESSURE, OBSERVE THE PRODUCT WATER FLOW METER. DO NOT EXCEED 7 GALLONS PER HOUR ON THE AQUA MINI 170 SYSTEM DO NOT EXCEED 14.5 GALLONS PER HOUR ON THE AQUA MINI 350 SYSTEM.

  • Page 43: Chapter 5: System Operation

    Feed water temperature and salinity vary depending upon location of operation. Feed water flow is fixed on the Aqua Mini 170 at .5 gallon per minute / 1.89 liters per minute; and on the Aqua Mini 350 at 1.5 gallons per minute / 5.68 liters per minute; Aqua Mini 550/750 at 3.5 gallon per minute / 13.25 liters per minuteby design.

  • Page 44: High/Low Pressure Fault Lamp Explanation

    Do not operate with feed water that exceeds 122 F / 50 C. High temperatures will cause structural damage to the R.O Membrane Element. 3. If any abnormality develops, stop the system and correct the problem. 4. Check for unusual noises or other occurrences. Sea Recovery Aqua Mini 170, 350, 550 and 750...

  • Page 45: Sea Recovery Mini Controller Operations

    System Operation Sea Recovery Mini Controller Operations Start/Stop button 1. Powers on and sets the system in its initial state. 2. When the system is producing water and the START/STOP button is pushed, the system stops all pumps and diverts water into the sea.

  • Page 46: Configuration (Change) Menu

    9. AutoShut Time – Auto shutdown after time (yes or no) 10. AutoShut Tank – Auto shutdown on tank full (yes or no) 11. FWF Duration – FWF duration time (HH:mm:ss) Sea Recovery Aqua Mini 170, 350, 550 and 750...

  • Page 47: Fresh Water Flush Button

    System Operation 12. FWF Interval – FWF interval time (HH:mm:ss) 13. AutoStart Tank – Autostart on tank empty (yes or no) 14. Salinity Level – Salinity error level (ppm) 15. Min Pressure – minimum pressure (Bar or PSI) 16. Max Pressure – Maximum pressure (Bar or PSI) 17.

  • Page 49: Chapter 6: System Storage And Cleaning

    Chapter System Storage and Cleaning R.O Membrane Element Handling and System Storage Cautions 1. TEMPERATURE: Never store the R.O. Membrane Element or Membrane/Vessel Assembly in direct sunlight. Never expose the R.O. Membrane Element or Membrane/Vessel Assembly to storage temperatures above 120 F / 50 C or below 32 F / 0 C.
  • Page 50 This is used to Rinse the System with Fresh Water, and also to Discharge the contents of the cleaning solution bucket. Sea Recovery Aqua Mini 170, 350, 550 and 750...
  • Page 51 System Storage and Cleaning This is used to Circulate Cleaning or Storage Solution through the system. This Illustration demonstrates a Once Through Rinse Configuration...

  • Page 52: Short Term Shutdown

    However, see “Winterizing and Freezing” note below. WINTERIZING AND FREEZING TEMPERATURE STORAGE NOTE: If the system is exposed to freezing temperatures, DO NOT activate the Automatic Fresh Water Flush. Instead, perform a Manual Fresh Water Rinse Sea Recovery Aqua Mini 170, 350, 550 and 750...

  • Page 53: Long Term Shutdown

    (1 gallon / 4 liters) food grade glycerin (propylene glycol) to the Storage Chemical Solution. This prevents the water in the system from freezing. 1. Close the Cock Valve [2]. 2. Replace the Pre-filtration Cartridges [6] with new Sea Recovery Pre-filtration Elements. 3. Fill a clean 5-gallon container with non-chlorinated product water.

  • Page 54: R.o. Membrane Element Cleaning Procedures

    After compensations, a 10% decline in productivity (GPH Flow) and/or a 10% increase in salt passage indicate that the R.O. Membrane Element may requires cleaning. Sea Recovery Aqua Mini 170, 350, 550 and 750...

  • Page 55: R.o. Membrane Element Cleaning Water And Chemical Requirements

    R.O. membrane element. If the R.O. Membrane Element is excessively fouled and in-field cleaning is not successful, the R.O. Membrane Element may be returned to Sea Recovery or to one of Sea Recovery’s many Service Dealers for professional chemical cleaning. If your membrane requires professional cleaning, please contact Sea Recovery for a Return Authorization Number, price quotation, and return instructions.
  • Page 56 Leave the Inlet Seacock Valve in the closed position. 30. If cleaning is complete and the system will be operated again within a short period of time: a) Reconnect the system’s Suction and Discharge Lines to normal operating position. Sea Recovery Aqua Mini 170, 350, 550 and 750...

  • Page 57: Chapter 7: Troubleshooting

    Chapter Troubleshooting System Shuts Down During Operation NUMBER ONE REPORTED PROBLEM IS “THE SYSTEM DOESN’T WORK”! We can’t help with this one unless you give us more information, or allow us to ask an unlimited number of questions. NUMBER TWO REPORTED PROBLEM IS "System Shut Down By Itself" with "ERROR ID 2" or "ERROR ID 3" (High/Low Pressure Fault) 1.

  • Page 58: Pressure Readings, Pressure Gauges, And Pressure Switches Abnormalities

    • Shut the system off, remove the leads from the low pressure switch, and using an ohm meter ensure that the switch circuit is “open”. • If the switch circuit is “closed”, adjust the switch per instructions in the maintenance section of this manual. Sea Recovery Aqua Mini 170, 350, 550 and 750...

  • Page 59: Product Water Flow And Product Water Quality

    Troubleshooting System remains in operation when the operating pressure is above 950 PSI. High Pressure Switch has drifted from factory setting. • Operate System and pressurize to 950 psi. Adjust High Pressure switch to “open” at 950 PSI. • Replace switch if necessary. Product Water Flow and Product Water Quality The system is operating at 850 psi and is not producing specified product water flow •...

  • Page 60: 3-Way Product Water Diversion Valve Abnormalities

    When the system is producing “unpotable” water and the Water Quality lamp is illuminated “red” the 3-way Product Water Diversion Valve coil will not receive voltage from the controller. This allows the 3-way Product Water Diversion Valve to divert the “unpotable” water to the Brine Discharge. Sea Recovery Aqua Mini 170, 350, 550 and 750...

  • Page 61: High Pressure Pump Abnormalities

    Troubleshooting When the system is producing “potable” water and the Water Quality lamp is illuminated “green”, the 3-way Product Water Diversion Valve coil will receive 12 VDC from the controller. This allows the 3-way Product Water Diversion Valve to divert the “potable” water to the post filtration section and on to the boat’s potable water storage tank. The Water Quality is less than 1000ppm, however, the Diversion Valve does not divert potable water to the post filtration section and on to the boat’s potable water storage tank.

  • Page 62: Booster Pump Abnormalities

    • Provide adequate power to the system. 6. Defective Start Switch on Touch Pad. • Test with Substitute Touch Pad. • Replace Touch Pad if one or more lamps or switches are found to be inoperable. Sea Recovery Aqua Mini 170, 350, 550 and 750...

  • Page 63: Maintenance And Repair

    Troubleshooting The Stop Switch is pressed, but the system does not stop. 1. Microprocessor has locked up. Turn main power off to the system at the power source circuit breaker for a minimum of 30 seconds to reset the microprocessor. 2.

  • Page 64: Weekly Quick Check

    This is based upon factual data compiled from Sea Recovery installations around the world. However, this schedule must be adjusted to each individual system depending upon the variables listed.
  • Page 65 Troubleshooting COMPONENT MAINTENANCE REQUIRED TIME INTERVAL CONTINUOUS TIME INTERVAL INTERMITTENT DUTY High Pressure Change oil First 50 Hours New Pump Break In Period Pump 500 hours Annually Replace Seal Kit 2000 hrs. / as required 2000 hrs. Replace Valve Kit 2000 hrs.

  • Page 67: Chapter 8: Electrical

    Electrical Requirements and Information Amperage Notes: The Electric Motors within the Aqua Mini 170 ,350, 550 & 750 systems start in series with time delay between each motor starting after the Touch Pad “Start” Switch is pressed. First, the Booster Pump starts, then the main High Pressure Pump Electric Motor starts.

  • Page 68: Motor Rotation

    0.0829 8.2525 53.4609 0.2893 0.0657 7.3482 42.3871 0.2576 0.0521 6.5430 33.6069 0.2294 0.0413 5.8268 26.6516 0.2043 0.0328 5.1892 21.1385 0.1620 0.0206 4.1148 13.2913 0.1285 0.0130 3.2639 8.3626 0.1019 0.0082 2.5883 5.2588 Sea Recovery Aqua Mini 170, 350, 550 and 750...
  • Page 69 Electrical Diameter Inch Square Inch (In2) Diameter Millimeters Square Millimeters (mm2) 0.0808 0.0051 2.0523 3.3064 0.0641 0.0032 1.6281 2.0809 0.0508 0.0020 1.2903 1.3070 0.0403 0.0013 1.0236 0.8225 0.0320 0.0008 0.8128 0.5186 0.0254 0.0005 0.6452 0.3267 American Wire Gauge Metric Wire Gauge Metric Wire dia inch sq.

  • Page 70: Electrical Line Drawings And Electrical Connections

    Electrical Line Drawings and Electrical Connections Wiring Diagram Aqua Mini 12vdc Sea Recovery Aqua Mini 170, 350, 550 and 750...

  • Page 71: Wiring Diagram Aqua Mini 24Vdc

    Electrical Wiring Diagram Aqua Mini 24vdc...

  • Page 72: Wiring Diagram Aqua Mini 110/220 Vac Single Phase

    Wiring Diagram Aqua Mini 110/220 VAC single phase Sea Recovery Aqua Mini 170, 350, 550 and 750...

  • Page 73: Aqua Mini 350,550,750 Electrical Diagram

    Electrical...

  • Page 75: Chapter 9: Maintenance And Repair

    Individual Component Maintenance and Repair 1. Inlet Thru Fitting [1]: Non Sea Recovery component. Keep the Inlet Thru Hull Fitting free and clear of debris and marine growth. If the Inlet Thru Hull Fitting is clogged, this results in a low feed pressure condition, which causes the system to shut off.

  • Page 76: Safety Requirements

    1. Turn off the water source to the UV unit. 2. Disconnect the power source to the UV unit. 3. Drain the UV treatment chamber. 4. Remove the ballast box cover. Sea Recovery Aqua Mini 170, 350, 550 and 750...
  • Page 77 Maintenance and Repair 5. Remove rubber boot and carefully pull out the UV lamp through the compression nut pass-thru. 6. Use a channel lock to remove the compression nuts. 7. Remove the Quartz Sleeve carefully. 8. Wash the Quartz Sleeve with mild soapy water and rinse in clean hot water. If dirt remains after rinsing, the quartz sleeve should be replaced.

  • Page 78: Checking For Leaks

    If both ends of the quartz sleeve are leaking, perform the following on both ends. 1. Use a channel lock to loosen and remove the compression nut. 2. Remove the quartz sleeve O-ring without pulling the quartz sleeve out. Sea Recovery Aqua Mini 170, 350, 550 and 750...

  • Page 79: Measuring Performance

    Vast majority of unsatisfactory Post-UV Test results are directly related to the improper sample-taking techniques. Although several commercial sample collection apparatuses are available, the proper manufacturer’s sample procedures must be followed. Note: Sea Recovery recommends a valve with a discharge orifice not to exceed ³” (6mm).

  • Page 80: Sampling Procedure

    2. Insert the quartz sleeve (close-end first) through the ballast box passthru until O-ring contact passthru. Screw on the ballast box compression nut. Insert view port O-ring and screw on view port compression nut.. Sea Recovery Aqua Mini 170, 350, 550 and 750...

  • Page 81: Ultraviolet Sterilizer [23]

    2. Remove the Charcoal Filter Element from the bowl. 3. Remove the O-Ring from the top of the bowl and take care to not damage it. 4. Replace the Charcoal Filter Element with a new Sea Recovery element. 5. Wipe the O-Ring with a damp cloth.

  • Page 82: Solenoid Valve Coil Check

    O-Ring bumpers, and tube stops. Clean the interior of the tube using a bottlebrush, soft rag, cotton swab or other soft item. Reassemble the unit. Sea Recovery Aqua Mini 170, 350, 550 and 750...

  • Page 83: High Pressure Pump Electric Motor

    Maintenance and Repair High Pressure Pump Electric Motor Troubleshoot electric motor failure to ensure that any abnormality from the power, wiring, wiring connections, contactor, or control circuit are not at fault or at cause. If the electric motor has failed, it will require replacement. Depending upon failure, replacement may be more cost effective than repair.

  • Page 84: Disassembly Of The Seal Assembly

    11. Examine Springs for damage or fatigue and replace as needed. Place on Plunger Rods. 12. Install Washers next with concave side towards Inlet Manifold. 13. Install Nuts and torque to 55 in. lbs. / 4 ft. lbs. / 4 Nm. Sea Recovery Aqua Mini 170, 350, 550 and 750...

  • Page 85: Reassembly Of The Discharge Valve Assembly

    Maintenance and Repair 14. Always install new Cotter pins and turn ends to secure in position. Reassembly of the Discharge Valve Assembly 1. Examine Adapter Spacer O-Rings and replace if worn. Lubricate and install O-Rings and Back-up-Rings on both front and rear of the Adapter Spacer. 2.
  • Page 86 12. Sparingly, lightly, lubricate: • 4 (four) NEW Brine O-Rings and 4 (four) new Product Water O-Rings for the Aqua Mini 170 or • 4 (four) NEW Brine O-Rings and 2 (two) new Product Water O-Rings for the Aqua Mini 350 13.

  • Page 87: Plankton Filter [5]

    Maintenance and Repair Figure 1: Inlet end of Pressure Vessel Brine Seal End of R.O. Membrane Element 17. Slide the Membrane Element into the High Pressure Vessel, past the brine seal, until the Membrane Element product water tube is 4 inches past the end lip of the High Pressure Vessel. 18.

  • Page 88: Pre-Filter [6] Element Replacement

    Use of String Wound or Fiber type elements will only lead to user frustration and very high maintenance costs. Use of third party prefilter elements will void any and all Sea Recovery warranty to the High Pressure Pump and the R.O. Membrane Element.

  • Page 89: Booster Pump Reassembly

    Maintenance and Repair 6. Remove seal head from the shaft. Slide from the shaft. 7. Remove four motor bolts and volute bracket from motor. 8. Remove seal seat from bracket. Booster Pump Reassembly 1. Clean seat cavity of the volute bracket thoroughly. 2.

  • Page 91: Chapter 10: System Logs

    Aqua Mini 170/350/550/750. Provide this information to service technicians when requesting technical assistance. Serial Number: _________________Model Number: Aqua Mini 170 _____; or Aqua Mini 350/550/750 _____ Name of Operator: ____________________________________________ Date: _________________________...
  • Page 92 _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ Sea Recovery Aqua Mini 170, 350, 550 and 750...

  • Page 93: Sea Recovery Aquamini 170,350,550,& 750 System Identification Information

    Sea Recovery AquaMini 170,350,550,& 750 System Identification Information INSTRUCTIONS: It is important that this form is completely filled in at the time of purchase of the Sea Recovery Aqua Mini 170,350,550,&750 Reverse Osmosis Desalinator. This information will be requested by our Service Department and Parts Order Desk whenever contacting Sea Recovery for technical assistance or by the Sales Department whenever ordering parts.

  • Page 94: Sea Recovery Aqua Mini 170,350,550, & 750 Daily Operation Log System Readings

    Sea Recovery Aqua Mini 170,350,550, & 750 Daily Operation Log System Readings Make copies of this blank form. At each shut down of the Aqua Mini 170 /350/550/750, record the following information. Retain these daily logs of the system performance for future reference and troubleshooting.

  • Page 95: Chapter 11: Glossary

    Chapter Glossary Terms Cascading Failure A failure in a system of interconnected parts in which the failure of a part can trigger the failure of successive parts. Boundary Layer (Also known as Concentration Polarization.) When water permeates through the membrane, nearly all the salt is left behind in the brine channel.
  • Page 96 The System over comes this factor by self adjusting the operating pressure to maintain a precise amount of Product Water Flow. Sea Recovery Aqua Mini 170, 350, 550 and 750...

  • Page 97: Chapter 12: Exploded Parts View

    Chapter Exploded Parts View...

  • Page 98: A041C Aqua Mini 170

    CONTROL MANIFOLD ASSY, MINIS (2012) B586220003 FRAME ASSY AQUA MINI 170 (2012) B595320007 CONTROLLER 110-220V AW MINI (2012) 061100043000 WASHER,FLAT,OS,1/4",SS 061142145012 BOLT HEX .25-20 X .75 SS 061160630012 SC PHIL PAN 10-24 X .75 SS Sea Recovery Aqua Mini 170, 350, 550 and 750...

  • Page 99: A051C Aqua Mini 350

    Exploded Parts View A051C AQUA MINI 350 ITEM NO. QTY. PART NUMBER DESCRIPTION B107230001 PREFILTER ASSY DUAL 350 B156230003 HP PUMP-MOTOR 110-220 50-60 1PH B196230001 MEMBRANE VESSEL ASSY AW 350 B502220003 MANIFOLD LP ASSY B502230003 CONTROL MANIFOLD ASSY, MINIS (2012) B586230003 FRAME ASSY, MINI 350 (2012) B595320007...

  • Page 100: A051C Aqua Mini 550

    CONTROL MANIFOLD ASSY, MINIS (2012) B586230003 FRAME ASSY, MINI 350 (2012) B595320007 CONTROLLER 110-220V AW MINI (2012) 061100043000 WASHER,FLAT,OS,1/4",SS 061142145012 BOLT HEX .25-20 X .75 SS 061160630012 SC PHIL PAN 10-24 X .75 SS Sea Recovery Aqua Mini 170, 350, 550 and 750...

  • Page 101: A051C Aqua Mini 750

    Exploded Parts View A051C AQUA MINI 750 ITEM NO. QTY. PART NUMBER DESCRIPTION B107230001 PREFILTER ASSY DUAL 350 B156230003 HP PUMP-MOTOR 110-220 50-60 1PH B196230003 MEMBRANE RACK ASSY AW-SF 750-1 B502220003 MANIFOLD LP ASSY B502230003 CONTROL MANIFOLD ASSY, MINIS (2012) B586230003 FRAME ASSY, MINI 350 (2012) B595320007...

  • Page 102: A052M Aqua Mini Modular

    HP PUMP-MOTOR 110-220 50-60 AW 550-750 1PH B196230002 MEMBRANE RACK ASSY AW-SF 500-1 B107230001 PREFILTER ASSY DUAL 350 061142145012 BOLT HEX .25-20 X .75 SS 061160630012 SC PHIL PAN 10-24 X .75 SS 061100043000 WASHER,FLAT,OS,1/4",SS Sea Recovery Aqua Mini 170, 350, 550 and 750...

  • Page 103: Booster Pump Assy Aw 170

    Exploded Parts View BOOSTER PUMP ASSY AW 170 ITEM NO. QTY. PART NUMBER DESCRIPTION 0112651900 ADAP .375 MPT X .50 BARB NYLON 061170628020 SC PHIL PAN A #10 X 1.25 SS 065080028000 WASHER FLAT #10 NYLON PART NUMBER: B016220001 BOOSTER PUMP ASSY AW170 12VDC ITEM NO.

  • Page 104: B016230003 Booster Pump Assy 350 Hp75 W-4.75In Impeller

    STRAIN RELIEF 90 CG90-6250 0112653700 ADAP .75 MPT X.75 BARB NYLON 01120737DG ELB90 .75 MPT X .75 BARB NYLON 061172143016 SCREW,HEX A,.25x1.00,SS 063200066000 NUT LOCK .50 STEEL 061142157016 SCREW,HEX HEAD,3/8-16x1",SS 061080056000 WASHER,FLAT,3/8",SS 061100043000 WASHER,FLAT,OS,1/4",SS Sea Recovery Aqua Mini 170, 350, 550 and 750...

  • Page 105: B196220017 Membrane Vessel Assy 170

    Exploded Parts View B196220017 MEMBRANE VESSEL ASSY 170 ITEM NO. QTY. PART NUMBER DESCRIPTION 05202402GR BRACKET MVA U-CLAMP 2453487000 END PLUG SINGLE 2.5 AW 170 2453497000 END PLUG 2.5 AW 170 2408132026 VESSEL 170 AW 2724010633 MEMBRANE VESSEL ASSY AW 170 0520210500 RETAINER PORT MVA AW 170 20201022000...
  • Page 106 Sea Recovery Aqua Mini 170, 350, 550 and 750...

  • Page 107: Membrane Vessel Assy Aw 350-750

    Exploded Parts View MEMBRANE VESSEL ASSY AW 350-750 ITEM NO. QTY. PART NUMBER DESCRIPTION 05202401GR BRACKET,MVA U-CLAMP,3 IN 2453502400 END PLUG SINGLE 3 AW 0520210600 RETAINER PORT MVA 2615180100 FELT ADHESIVE 0.125 X 0.75 STRIP 2453512400 END PLUG DUAL 3 IN AW 0204010869 ELB90 .25 TUBE x .25 FNPT PLASTIC 1317011769...
  • Page 108 Sea Recovery Aqua Mini 170, 350, 550 and 750...

  • Page 109: Anatomy Of A Spiral Wound Reverse Osmosis Membrane Element

    Exploded Parts View Anatomy of a Spiral Wound Reverse Osmosis Membrane Element A A N AT O M Y O F A SPI RAL W O U N D REV ERSE O SM O SI S M EM BRAN E EL EM EN T...

  • Page 110: Hp Pump-Motor 12Vdc-24Vdc Aw

    WASHER,LOCK,3/8",SS B156220012 HP PUMP-MOTOR 12VDC ITEM NO. QTY. PART NUMBER DESCRIPTION 15093110CF MOTOR .33HP 12 VDC B156220024 HP PUMP-MOTOR 24VDC ITEM NO. QTY. PART NUMBER DESCRIPTION 15103210CF MOTOR .33HP 24 VDC Sea Recovery Aqua Mini 170, 350, 550 and 750...
  • Page 111 Exploded Parts View RECOMMENDED SPARES: QTY. PART NUMBER DESCRIPTION B653220001 HPP -C SEAL KIT B654220001 HPP -C INLET VALVE REBUILD KIT B652220001 HPP -C PMP KIT SEALS/VALVES...

  • Page 112: B156220110 Hp Pump-Motor 110-220 50-60 Aw 170

    HOSE CLAMP .75 SS 061060050000 NUT HEX .31-18 W-INSERT SS 0117341869 PLUG .375 MNPT SS 061142150016 SCREW,HEX HEAD,.31-18x1.00,SS 061142157024 SCREW,HEX HEAD,3/8-16x1-1/2",SS 1904010543 STRAIN RELIEF 8400 1904013543 STRAIN RELIEF 8423 061080056000 WASHER,LOCK,3/8",SS 061100049000 WASHER,FLAT,OS,5/16",SS Sea Recovery Aqua Mini 170, 350, 550 and 750...
  • Page 113 Exploded Parts View RECOMMENDED SPARES: QTY. PART NUMBER DESCRIPTION B653220001 HPP -C SEAL KIT B654220001 HPP -C INLET VALVE REBUILD KIT B652220001 HPP -C PMP KIT SEALS/VALVES...

  • Page 114: B156230003 Hp Pump-Motor 110-220 50-60 1Ph

    0117341869 PLUG .375 MNPT SS 061060050000 NUT HEX .31-18 W-INSERT SS 061080056000 WASHER,FLAT,3/8",SS 061100049000 WASHER,FLAT,OS,5/16",SS 061120056000 WASHER,LOCK,3/8",SS 061142150016 SCREW,HEX HEAD,.31-18x1.00,SS 061142157024 SCREW,HEX HEAD,3/8-16x1-1/2",SS 1904010543 STRAIN RELIEF 8400 1904013543 STRAIN RELIEF 8423 Sea Recovery Aqua Mini 170, 350, 550 and 750...
  • Page 115 Exploded Parts View RECOMMENDED SPARES: QTY. PART NUMBER DESCRIPTION B653220001 HPP -C SEAL KIT B654220001 HPP -C INLET VALVE REBUILD KIT B652220001 HPP -C PMP KIT SEALS/VALVES...

  • Page 116: B156230001 Hp Pump-Motor 110-220-60Hz Aw350

    HOSE CLAMP .75 SS 061060050000 NUT HEX .31-18 W-INSERT SS 0117341869 PLUG .375 MNPT SS 061142150016 SCREW,HEX HEAD,.31-18x1.00,SS 061120056000 WASHER,LOCK,3/8",SS 1904010543 STRAIN RELIEF 8400 1904013543 STRAIN RELIEF 8423 061080056000 WASHER,FLAT,3/8",SS 061100049000 WASHER,FLAT,OS,5/16",SS Sea Recovery Aqua Mini 170, 350, 550 and 750...
  • Page 117 Exploded Parts View RECOMMENDED SPARES: QTY. PART NUMBER DESCRIPTION B653220001 HPP -C SEAL KIT B654220001 HPP -C INLET VALVE REBUILD KIT B652220001 HPP -C PMP KIT SEALS/VALVES...

  • Page 118: B156230003 Hp Pump-Motor 110-220 50-60 1Ph

    0117341869 PLUG .375 MNPT SS 061060050000 NUT HEX .31-18 W-INSERT SS 061080056000 WASHER,FLAT,3/8",SS 061100049000 WASHER,FLAT,OS,5/16",SS 061120056000 WASHER,LOCK,3/8",SS 061142150016 SCREW,HEX HEAD,.31-18x1.00,SS 061142157024 SCREW,HEX HEAD,3/8-16x1-1/2",SS 1904010543 STRAIN RELIEF 8400 1904013543 STRAIN RELIEF 8423 Sea Recovery Aqua Mini 170, 350, 550 and 750...
  • Page 119 Exploded Parts View RECOMMENDED SPARES: QTY. PART NUMBER DESCRIPTION B653220001 HPP -C SEAL KIT B654220001 HPP -C INLET VALVE REBUILD KIT B652220001 HPP -C PMP KIT SEALS/VALVES...

  • Page 120: B156230004 Hp Pump-Motor 110-220 50-60 Aw 550-750 1Ph

    HOSE CLAMP .75 SS 061060050000 NUT HEX .31-18 W-INSERT SS 0117341869 PLUG .375 MNPT SS 061142150016 SCREW,HEX HEAD,.31-18x1.00,SS 061142157024 SCREW,HEX HEAD,3/8-16x1-1/2",SS 1904010543 STRAIN RELIEF 8400 1904013543 STRAIN RELIEF 8423 061080056000 WASHER,FLAT,3/8",SS 061100049000 WASHER,FLAT,OS,5/16",SS Sea Recovery Aqua Mini 170, 350, 550 and 750...
  • Page 121 Exploded Parts View RECOMMENDED SPARES: QTY. PART NUMBER DESCRIPTION B653220001 HPP -C SEAL KIT B654220001 HPP -C INLET VALVE REBUILD KIT B652220001 HPP -C PMP KIT SEALS/VALVES...

  • Page 122: B502220003 Manifold Lp Assy

    Mini 170 ITEM NO. QTY. PART NUMBER DESCRIPTION 2317100200 TRANSDUCER 0-200 PSI .437 SAE 5333220901 MANIFOLD LP AW 170 0204090869 FITTING,PP,1/4 ODx1/4 MT 061161130012 SC PHIL OVAL #10-24 X .75 SS Sea Recovery Aqua Mini 170, 350, 550 and 750...

  • Page 123: B156230001M Hp Pump-Motor 110-220-60Hz Aw350-Modular

    Exploded Parts View B156230001M HP PUMP-MOTOR 110-220-60HZ AW350-MODULAR ITEM NO. QTY. PART NUMBER DESCRIPTION 2020054903A PANEL MOTOR BASE PLATE 1218181422 HP PUMP 1.5 GPM SS CAT 1535231010 MOTOR,1HP,120V,60HK,1 PH 2115030120 RUBBER MOUNT 55 AQUA SERIES 1920023632 STRAIN RELIEF 90 CG90-6250 1317061900 ELB45-6 FLARE X 3-8 MT SS 0112021800...
  • Page 124 RECOMMENDED SPARES: QTY. PART NUMBER DESCRIPTION B653220001 HPP -C SEAL KIT B654220001 HPP -C INLET VALVE REBUILD KIT B652220001 HPP -C PMP KIT SEALS/VALVES Sea Recovery Aqua Mini 170, 350, 550 and 750...

  • Page 125: B156230002M Hp Pump-Motor 110-220 50Hz Aw 350-Modular

    Exploded Parts View B156230002M HP PUMP-MOTOR 110-220 50HZ AW 350-MODULAR ITEM NO. QTY. PART NUMBER DESCRIPTION 2020054903A PANEL MOTOR BASE PLATE 1218181422 HP PUMP 1.5 GPM SS CAT 1534231010 MOTOR 1 HP 115-220-50-1 PH 2115030120 RUBBER MOUNT 55 AQUA SERIES 1920023632 STRAIN RELIEF 90 CG90-6250 1317061900...
  • Page 126 RECOMMENDED SPARES: QTY. PART NUMBER DESCRIPTION B653220001 HPP -C SEAL KIT B654220001 HPP -C INLET VALVE REBUILD KIT B652220001 HPP -C PMP KIT SEALS/VALVES Sea Recovery Aqua Mini 170, 350, 550 and 750...

  • Page 127: B156230004M Hp Pump-Motor 110-220 50-60 Aw 550-750 1Ph-Modular

    Exploded Parts View B156230004M HP PUMP-MOTOR 110-220 50-60 AW 550-750 1PH-MODULAR ITEM NO. QTY. PART NUMBER DESCRIPTION 2020054903A PANEL MOTOR BASE PLATE 15AD062412 MOTOR 2.1 HP 50-60 110-220 1PH 2115030120 RUBBER MOUNT 55 AQUA SERIES 1218182422 HP PUMP 3.5 GPM SS 1920023632 STRAIN RELIEF 90 CG90-6250 1317061900...
  • Page 128 RECOMMENDED SPARES: QTY. PART NUMBER DESCRIPTION B653220001 HPP -C SEAL KIT B654220001 HPP -C INLET VALVE REBUILD KIT B652220001 HPP -C PMP KIT SEALS/VALVES Sea Recovery Aqua Mini 170, 350, 550 and 750...

  • Page 129: B502220003M Manifold Lp Assy

    Exploded Parts View B502220003M MANIFOLD LP ASSY Mini 350, 550, 750 ITEM NO. QTY. PART NUMBER DESCRIPTION 2317100200 TRANSDUCER 0-200 PSI .437 SAE 5333220901 MANIFOLD LP AW 170 0204020869 ELBOW,PP,1/4 ODx1/4 MT 061161130012 SC PHIL OVAL #10-24 X .75 SS...

  • Page 130: B502230004 Control Manifold Assy

    SC PHIL PAN A #6 X .75 SS H30612730006 INSERT 8-32 X .31-18 SS 2614015800 O-RING 011 GAUGE-PRES SWITCH 2614017100 O-RING 111 SALINITY PRB-BPR CS 061160526048 SC 8-32 x 3.00 SS 061162020008 SC PHIL FLAT #6-32 x .50SS Sea Recovery Aqua Mini 170, 350, 550 and 750...
  • Page 131 Exploded Parts View...

  • Page 132: B502230003 Control Manifold Assy

    SC PHIL PAN A #6 X .75 SS H30612730006 INSERT 8-32 X .31-18 SS 2614015800 O-RING 011 GAUGE-PRES SWITCH 2614017100 O-RING 111 SALINITY PRB-BPR CS 061160526048 SC 8-32 x 3.00 SS 061162020008 SC PHIL FLAT #6-32 x .50SS Sea Recovery Aqua Mini 170, 350, 550 and 750...
  • Page 133 Exploded Parts View...

  • Page 134: B502230003M Control Manifold Assy Modular

    ELB90 ST 1/4 MPT X1/4 FPT 316SS -W/ORING H30612730006 INSERT 8-32 X .31-18 SS 2614015800 O-RING 011 GAUGE-PRES SWITCH 2614017100 O-RING 111 SALINITY PRB-BPR CS 061160526048 SC 8-32 x 3.00 SS 061162020008 SC PHIL FLAT #6-32 x .50SS Sea Recovery Aqua Mini 170, 350, 550 and 750...
  • Page 135 Exploded Parts View...

  • Page 136: 1401096100 3-Way Product Water Diversion Solenoid Valve

    1401096100 3-WAY PRODUCT WATER DIVERSION SOLENOID VALVE PORT DESIGNATION & DESCRIPTION (WATER FLOW) Sea Recovery Aqua Mini 170, 350, 550 and 750...

  • Page 137: B107220002 Prefilter Assy 170

    Exploded Parts View B107220002 PREFILTER ASSY 170 ITEM NO. QTY. PART NUMBER DESCRIPTION 20200402102 BRACKET SINGLE FILTER 0713020573 FILTER HOUSING-LID .375 X 10 ASM 0801060157 ELEMENT PREFILTER 10-05 0112072500 ELB90 0.50 MPT x 0.50 BARB 061172143016 SCREX,HEX A,.25x1.00,SS 05181432AA CLAMP,HOSE,SS,1/2" 061170628016 SC PHIL PAN A #10 X 1 SS 065080028000...
  • Page 138 RECOMMENDED SPARES: QTY. PART NUMBER DESCRIPTION 2614010473 ORING BLUE HSG 237 Sea Recovery Aqua Mini 170, 350, 550 and 750...

  • Page 139: B107230001 Prefilter Assy Dual 350

    Exploded Parts View B107230001 PREFILTER ASSY DUAL 350 ITEM NO. QTY. PART NUMBER DESCRIPTION 20200402101 DUAL BRACKET PREFILTER-CHRCL-PLNKTN Rev A 0713020873-1 FILTER HOUSING .50 X 10 LID 0713020873-2 FILTER HOUSING .50 X 10 BODY 0713020873-3 FILTER HOUSING .50 X 10 O-RING 0801060157 ELEMENT PREFILTER 10-05 0801130257...
  • Page 140 RECOMMENDED SPARES: QTY. PART NUMBER DESCRIPTION 2614010473 ORING BLUE HSG 237 Sea Recovery Aqua Mini 170, 350, 550 and 750...

  • Page 141: B598000009 Fresh Water Flush 10" Housing

    Exploded Parts View B598000009 FRESH WATER FLUSH 10" HOUSING ITEM NO. QTY. PART NUMBER DESCRIPTION 20200402102 BRACKET SINGLE FILTER 0713020573 FILTER HOUSING-LID .375 X 10 ASM 0801060157 ELEMENT PREFILTER 10-05 0112072500 ELB90 0.50 MPT x 0.50 BARB 061172143016 SCREX,HEX A,.25x1.00,SS 05181432AA CLAMP,HOSE,SS,1/2"...
  • Page 142 RECOMMENDED SPARES: QTY. PART NUMBER DESCRIPTION 2614010473 ORING BLUE HSG 237 Sea Recovery Aqua Mini 170, 350, 550 and 750...

  • Page 143: B521220002 Charcoal Filter Assy 170-350

    Exploded Parts View B521220002 CHARCOAL FILTER ASSY 170-350 ITEM NO. QTY. PART NUMBER DESCRIPTION 20200402102 BRACKET SINGLE FILTER 0713020573 FILTER HOUSING-LID .375 X 10 ASM 0803004773 ELEMENT CHARCOAL 10.0 01100719FX ELB9 0.375MPT X 0.50 BARBTEFBLU 0204020969 ELB90 .25 TUBE x .375 MPT PLASTIC 0204021869 ELBOW,SS,3/8 ODx3/8 MT 061170628016...
  • Page 144 RECOMMENDED SPARES: QTY. PART NUMBER DESCRIPTION 2614010473 ORING BLUE HSG 237 Sea Recovery Aqua Mini 170, 350, 550 and 750...

  • Page 145: B107230005 Commercial Prefilter Assy

    Exploded Parts View B107230005 COMMERCIAL PREFILTER ASSY ITEM NO. QTY. PART NUMBER DESCRIPTION 07620310WA FILTER HOUSING 32.5 SQFT 0801063357 ELEMENT CPFE 5 MIC 32.5 SQFT 10180103CC GAUGE -30-0-70 BPM.NPT 1404553800 VALVE AIR BLEED .25 TUBE X .25 TUBE 0112653706 ADAP .75 MPT X .63 BARB NYLON 061172143016 SCREX,HEX A,.25x1.00,SS 0204090300...
  • Page 146 Sea Recovery Aqua Mini 170, 350, 550 and 750...

  • Page 147: B107230010 Oil Water Separator Assy

    Exploded Parts View B107230010 OIL WATER SEPARATOR ASSY ITEM NO. QTY. PART NUMBER DESCRIPTION 08020723KD ELEMENT OWSE 32.5 SQFT 07620310WA FILTER HOUSING 32.5 SQFT 0112653706 ADAP .75 MPT X .63 BARB NYLON 061172143016 SCREX,HEX A,.25x1.00,SS 0204990300 PLUG .25 JQ 05181434AA CLAMP,HOSE,SS,3/4"...
  • Page 148 Sea Recovery Aqua Mini 170, 350, 550 and 750...

  • Page 149: B001220001 Installation Kit Aw/Sf 170

    Exploded Parts View B001220001 INSTALLATION KIT AW/SF 170 ITEM NO. QTY. PART NUMBER DESCRIPTION 01120125DG ELB90 1/2 FPT x 1/2FPT NYL 0112651900 ADAP 3/8 MPT x 1/2 BARB NYL 0112652500 ADAP 1/2 MPT X 1/2 BARB NYL 0112653600 ADAP 3/4 MPT X 1/2 BARB NYL 0204020869 ELB90 1/4 MPT X 1/4 TU PLASTIC 0204091969...

  • Page 150: B001230001 Installation Kit Aw/Sf 350-750

    061080028000 WASHER FLAT #10 SS 061170628016 SC PHIL PAN "A" # 10 X 1" L SS 061172143016 SC HEX "A" 1/4 X 1" L SS 061100043000 WASHER FLAT OS 1/4 SS Sea Recovery Aqua Mini 170, 350, 550 and 750...

  • Page 151: B611000004 Remote Assy Lcd Controller 80' Src

    Exploded Parts View B611000004 REMOTE ASSY LCD CONTROLLER 80' SRC ITEM NO. QTY. PART NUMBER DESCRIPTION 4900283104 CABLE MULTIST 8 CON WHT 3131100900 EZ PLUG RJ45 31315606WE REMOTE TOUCH PAD 170...

  • Page 152: B5262000Cv Uv Sterilizer

    061182143024 SC LAG 0.25 X 1.50 SS 065070045000 NUT HEX .25-20 FLANGED 065080028000 WASHER FLAT #10 NYLON 2614019000 O-RING 212 QUARTZ SLEEVE B651830001A OWNERS MANUAL QUICK INSTALLATION UV LIGHT SP SERIES Sea Recovery Aqua Mini 170, 350, 550 and 750...
  • Page 153 Exploded Parts View...

  • Page 154: B5968000Xx Soft Start Assy 115-230 V

    B5968000XX SOFT START ASSY 115-230 V ITEM NO. MANUAL ASSY PART NUMBER DESCRIPTION DWG/QTY. B596800015 SOFT START 115V 50-60HZ B596800014 SOFT START 230V 50-60HZ Note: PLEASE SPECIFY VOLTAGE WHEN ORDERING Sea Recovery Aqua Mini 170, 350, 550 and 750...
  • Page 155 Exploded Parts View...

  • Page 156: Hp Hose Assembly

    HP HOSE ASSEMBLY ITEM NO. QTY. PART NUMBER DESCRIPTION 2432160669 HOSE HP - 6P 1317481969 SWIVEL FITTING - 6 SSP Sea Recovery Aqua Mini 170, 350, 550 and 750...

  • Page 157: Available Tubes And Fittings

    Exploded Parts View AVAILABLE TUBES AND FITTINGS PART NO DESCRIPTION 1. CONNECTOR MALE 0204090669 1/4 inch tube x 1/8 inch mnpt 0204090869 1/4 inch tube x 1/4 inch mnpt 0204091669 3/8 inch tube x 1/8 inch mnpt 0204091769 3/8 inch tube x 1/4 inch mnpt 0204091869 3/8 inch tube x 3/8 inch mnpt 0204091969...
  • Page 158 1/2 inch tube x 3/8 inch tube 0204242569 1/2 inch tube 0204242869 5/8 inch tube x 3/8 inch tube 0204243069 5/8 inch tube 8. UNION 0204210869 1/4 inch tube 0204211769 3/8 inch tube x 1/4 inch tube Sea Recovery Aqua Mini 170, 350, 550 and 750...
  • Page 159 Exploded Parts View PART NO DESCRIPTION 0204211869 3/8 inch tube 0204212469 1/2 inch tube x 3/8 inch tube 0204212569 1/2 inch tube 0204212869 5/8 inch tube x 3/8 inch tube 0204212969 5/8 inch tube x 1/2 inch tube 0204213069 5/8 inch tube 9.

  • Page 160: Tube Compression Fittings Replacement Parts

    TUBE 3/8 BLACK 0312123569 FOR 1/2" O.D. TUBE NUT/SPACE/GRAB & O-RING 1/2" 0204-1/269 TUBE 1/2 BLACK NO SUBSTITUTE 0312124269 FOR 5/8" O.D. TUBE NUT/SPACER/GRAB & O-RING 5/8" 0204-5/869 TUBE 5/8 BLACK POLYPRO 0305125169 Sea Recovery Aqua Mini 170, 350, 550 and 750...

  • Page 161: Clean/Rinse Inlet Valve

    Exploded Parts View Clean/Rinse Inlet Valve CLEAN/RINSE INLET VALVE C C L EAN / RI N SE I N L ET V AL V E C L EAN / RI N SE O U T L ET V AL V E...

  • Page 163: Chapter 13: Appendix

    Chapter Appendix...

  • Page 166: Fcc Compliance

    Appendix FCC Compliance...
  • Page 167 Marine & Offshore Application - Production of Fresh Water by Sea Desalination Intended Service: Reverse Osmosis Desalination Unit Description: Model: Aqua Mini 170 GPD, Aqua Mini 350 GPD, Aqua Mini 550 GPD, Aqua Mini Ratings: 705 GPD. Unit Certification is not required for this product. If the manufacturer or purchaser...
  • Page 168 Certificate Number: 05-HS122694A-2-PDA and specifications used to evaluate the Product, will require re-evaluation of the PDA. Use of the Product for non ABS classed vessels, MODUs or facilities is to be to an agreement between the manufacturer and intended client. 2010 Steel Vessels Rules 1-1-4/7.7, 1-1-Appendix 3, 4-6-2/5.7, 4-6-2/5.7 ABS Rules: National Standards:...
  • Page 169 SEA RECOVERY declares that the following models conform to the EN 55011A and EN 50082-2 standards: Product Series: Model Names: Aqua Matic Series Aqua Matic Aqua Whisper Series Aqua Whisper / DX Aqua Whisper Mini Series Aqua Whisper Mini Ultra Whisper Series...
  • Page 170 Sea Recovery 2630 E. El Presidio Street Carson, CA 90810 sales@searecovery.com www.searecovery.com Manual PN B651220001B...

This manual is also suitable for:

Aqua mini 350Aqua mini 550Aqua mini 750

Table of Contents

Save PDF