Sony MEX-N5100BE Service Manual
  1. Manuals
  2. Brands
  3. Sony Manuals
  4. Car Receiver
  5. MEX-N5100BE
  6. Service manual

Sony MEX-N5100BE Service Manual

Sony bluetooth car audio system
Hide thumbs
Table of Contents

Advertisement

Quick Links

SERVICE MANUAL
Ver. 1.0 2014.12
The service manual of the mechanism deck, used in
this model, has been issued in a separate volume.
Please refer to the service manual of the MG-101
series for the mechanism deck information.
• The tuner and CD sections have no adjustments.
(US and Canadian models only)
FOR THE CUSTOMERS IN THE USA. NOT
APPLICABLE IN CANADA, INCLUDING IN THE
PROVINCE OF QUEBEC.
POUR LES CLIENTS AUX ÉTATS-UNIS. NON
APPLICABLE AU CANADA, Y COMPRIS LA
PROVINCE DE QUÉBEC.
AUDIO POWER SPECIFICATIONS
CEA2006 Standard
Power Output: 17 Watts RMS × 4 at 4
Ohms < 1% THD+N
SN Ratio: 80 dBA
(reference: 1 Watt into 4 Ohms)
Tuner section
(US and Canadian models)
FM
Tuning range: 87.5 – 107.9 MHz
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency:
FM CCIR: -1,956.5 to -487.3 kHz and
+500.0 to +2,095.4 kHz
Usable sensitivity: 8 dBf
Selectivity: 75 dB at 400 kHz
Signal-to-noise ratio: 73 dB
Separation: 50 dB at 1 kHz
Frequency response: 20 – 15,000 Hz
AM
Tuning range: 530 – 1,710 kHz
Antenna (aerial) terminal:
External antenna (aerial) connector
Sensitivity: 26 μV
9-896-114-01
Sony Corporation
2014L33-1
©
2014.12
Published by Sony Techno Create Corporation
MEX-N5100BE/N5100BT/
Photo: MEX-N5100BT
Model Name Using Similar Mechanism
Mechanism Type
Optical Pick-up Name

SPECIFICATIONS

(AEP and UK models)
MW/LW
Tuning range:
FM
Tuning range: 87.5 – 108.0 MHz
Antenna (aerial) terminal:
External antenna (aerial) connector
Antenna (aerial) terminal:
Intermediate frequency:
FM CCIR: -1,956.5 to -487.3 kHz and
Sensitivity: MW: 26 μV, LW: 50 μV
+500.0 to +2,095.4 kHz
Usable sensitivity: 8 dBf
(E, Mexican, Indian and Australian models)
Selectivity: 75 dB at 400 kHz
FM
Signal-to-noise ratio: 73 dB
Tuning range:
Separation: 50 dB at 1 kHz
Frequency response: 20 – 15,000 Hz
MW/LW
Tuning range:
FM tuning step:
MW: 531 – 1,602 kHz
LW: 153 – 279 kHz
Antenna (aerial) terminal:
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency:
Sensitivity: MW: 26 μV, LW: 50 μV
(Russian model)
Usable sensitivity: 8 dBf
Selectivity: 75 dB at 400 kHz
FM
Tuning range:
Signal-to-noise ratio: 73 dB
Separation: 50 dB at 1 kHz
FM1/FM2: 87.5 – 108.0 MHz
(at 50 kHz step)
Frequency response: 20 – 15,000 Hz
FM3: 65 – 74 MHz (at 30kHz step)
AM
Antenna (aerial) terminal:
Tuning range:
External antenna (aerial) connector
Intermediate frequency:
FM CCIR: -1,956.5 to -487.3 kHz and
AM tuning step:
+500.0 to +2,095.4 kHz
FM OIRT: -1,815.6 to -943.7 kHz and
Antenna (aerial) terminal:
+996.6 to +1,776.6 kHz
Usable sensitivity: 8 dBf
Sensitivity: 26 μV
Selectivity: 75 dB at 400 kHz
Signal-to-noise ratio: 73 dB
Separation: 50 dB at 1 kHz
Frequency response: 20 – 15,000 Hz
Canadian Model
Australian Model
MW: 531 – 1,602 kHz
LW: 153 – 279 kHz
External antenna (aerial) connector
87.5 – 108.0 MHz (at 50 kHz step)
87.5 – 108.0 MHz (at 100 kHz step)
87.5 – 107.9 MHz (at 200 kHz step)
50 kHz/100 kHz/200 kHz switchable
External antenna (aerial) connector
FM CCIR: -1,956.5 to -487.3 kHz and
+500.0 to +2,095.4 kHz
531 – 1,602 kHz (at 9 kHz step)
530 – 1,710 kHz (at 10 kHz step)
9 kHz/10 kHz switchable
External antenna (aerial) connector
– Continued on next page –
N5150BT
US Model
AEP Model
UK Model
MEX-N5100BT
E Model
MEX-N5150BT
Russian Model
MEX-N5100BE
MEX-N5000BE/N5000BT/
N5050BT/N5070BT
MG-101CF-188
DAX-25A
(Saudi Arabia model)
FM
Tuning range: 87.5 – 108.0 MHz
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency:
FM CCIR: -1,956.5 to -487.3 kHz and
+500.0 to +2,095.4 kHz
Usable sensitivity: 8 dBf
Selectivity: 75 dB at 400 kHz
Signal-to-noise ratio: 73 dB
Separation: 50 dB at 1 kHz
Frequency response: 20 – 15,000 Hz
MW
Tuning range: 531 – 1,602 kHz
Antenna (aerial) terminal:
External antenna (aerial) connector
Sensitivity: 26 μV
SW
Tuning range:
SW1: 2,940 – 7,735 kHz
SW2: 9,500 – 18,135 kHz
(except for 10,140 – 11,575 kHz)
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency:
-2,463.8 to -1,710.1 kHz and
+1,710.0 to +2,418.4 kHz
Sensitivity: 26 μV
AUDIO SYSTEM

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MEX-N5100BE and is the answer not in the manual?

Questions and answers

Related Manuals for Sony MEX-N5100BE

Summary of Contents for Sony MEX-N5100BE

  • Page 1: Specifications

    Selectivity: 75 dB at 400 kHz Signal-to-noise ratio: 73 dB Separation: 50 dB at 1 kHz Frequency response: 20 – 15,000 Hz – Continued on next page – AUDIO SYSTEM 9-896-114-01 Sony Corporation 2014L33-1 © 2014.12 Published by Sony Techno Create Corporation...
  • Page 2 Bluetooth SIG, Inc. and any documentation and/or other materials provided USB Player section (US and Canadian models only) use of such marks by Sony Corporation is under with the distribution. Remote controller input terminal Interface: USB (High-speed) license.

  • Page 3: Table Of Contents

    MEX-N5100BE/N5100BT/N5150BT SECTION 1 SERVICING NOTES TABLE OF CONTENTS The SERVICING NOTES contains important information for servicing. Be sure to read this section before repairing the SERVICING NOTES unit..........GENERAL ..............15 NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT DISASSEMBLY 3-1.
  • Page 4 MEX-N5100BE/N5100BT/N5150BT REPLACING THE LITHIUM BATTERY OF THE REMOTE 1-2. Display in Destination Setting Mode COMMANDER (Except AEP, UK and Australian models only) (Displayed characters/values in the following fi gure are example) Under normal conditions, the battery will last Destination code approximately 1 year.
  • Page 5 SRC] button for 1 second after the confi rming ends, and the 4-548-075-0[] MEX-N5100BT: US and Canadian models (UC) unit returns to the normal condition. 4-548-076-0[] MEX-N5100BT: AEP and UK models (EUR) MEX-N5100BE: Russian model (RU2) 4-548-077-0[] MEX-N5150BT: E model (E) 4-548-078-0[] MEX-N5150BT: Australian model (ET4) 4-548-079-0[]...
  • Page 6 MEX-N5100BE/N5100BT/N5150BT TEST DISCS IMPORTANT NOTE OF “INITIALIZING” Use following TEST DISC (for CD) when this unit confi rms the The purpose of “Bluetooth Initialize” is to initialize the Bluetooth operation and checks it. connection history (HF/Audio Streaming). (To delete the device information for the devices that you connected to when searching, Part No.
  • Page 7 Even if you see no indications or wrong indications, they are not fail- lect from connectable cellular phones list) ures of this unit. • Bluetooth audio devices (SONY NWZ-A826, or select from connectable cellular phones/audio devices list) 1. Search for this unit from the Bluetooth device (cellular phone), •...
  • Page 8 MEX-N5100BE/N5100BT/N5150BT BLUETOOTH INFORMATION WRITING METHOD 9. Refer to the “6. Version Check Method of the NFC Tag Data Writing Application for the Servicing” on the page 12, and When the complete MAIN board, knob (VOL) (SV) assy or front check the version of NFCtagWriter.apk.
  • Page 9 MEX-N5100BE/N5100BT/N5150BT How to display on the liquid crystal display by the 6. Input the Bluetooth address (BD_ADDR). (Input the Bluetooth address (BD_ADDR) that written on the test mode: BT module label with the keyboard on the smartphone, or tap 1. In the state of source off (the clock is displayed on the the “QR”...
  • Page 10 MEX-N5100BE/N5100BT/N5150BT 10. End the NFCtagWriter application on the smartphone. 17 Tap the “Read” on the screen of the smartphone. 11. Check the operation of connecting with the smartphone by one touch (NFC). “OPERATION CHECK OF THE NFC AFTER (Refer to the COMPLETING THE REPAIRS”...
  • Page 11 MEX-N5100BE/N5100BT/N5150BT 4. Check Method of the NFC Tag Data How to display on the liquid crystal display by the Check the NFC tag data according to the procedure below. test mode: 1. In the state of source off (the clock is displayed on the...
  • Page 12 MEX-N5100BE/N5100BT/N5150BT 5. The Factor that One Touch Connection is Impossible The four following factors are considered as the factor that one touch connection is impossible. Guess and check the defective factor by each checking result. Note: The four following factors are examples.
  • Page 13 MEX-N5100BE/N5100BT/N5150BT • Please cut out along the dotted line and use it. Notice about the serial number change on the back side of Notice about the serial number change on the back side of the front panel: the front panel:...
  • Page 14 MEX-N5100BE/N5100BT/N5150BT MEMO...

  • Page 15: General

    MEX-N5100BE/N5100BT/N5150BT SECTION 2 This section is extracted GENERAL from instruction manual. (US and Canadian models) Connection (For MEX-N5100BT) Connection/Installation Subwoofer* Cautions Run all ground (earth) leads to a common ground (earth) point. Do not get the leads trapped under a screw, or caught in moving parts (e.g., seat railing).
  • Page 16 If the fuse blows to dashboard/center console again after replacement, there may be an internal malfunction. In such a case, consult your nearest Sony dealer. Bracket Bracket Existing parts supplied with your car...
  • Page 17 MEX-N5100BE/N5100BT/N5150BT (AEP and UK models) Connection (For MEX-N5100BT) Connection/Installation Subwoofer* Cautions Run all ground (earth) leads to a common ground (earth) point. Do not get the leads trapped under a screw, or caught in moving parts (e.g., seat railing). Before making connections, turn the car ignition Power amplifier* off to avoid short circuits.
  • Page 18 If the fuse blows, check the power connection and replace the fuse. If the fuse blows again after replacement, there may be an internal malfunction. In such a case, consult your nearest Sony dealer.
  • Page 19 микрофона см. на “Установка микрофона (только *2 Полное сопротивление громкоговорителей: ” *7 В зависимости от типа автомобиля используйте MEX-N5100BE)” (стр. 37). 4–8 Ом × 4 Примечание относительно провода питания адаптер (не входит в комплект поставки), если *7 В зависимости от типа автомобиля используйте...
  • Page 20 плотную фиксацию. замените предохранитель. Если после замены предохранитель снова перегорел, это может 182 мм означать неисправность устройства. В этом случае обратитесь к ближайшему дилеру Sony. 53 мм Примечания Если фиксаторы не согнуты или выгнуты наружу, устройство не будет установлено надлежащим...
  • Page 21 MEX-N5100BE/N5100BT/N5150BT (E, Saudi Arabia, Mexican, Indian and Australian models) Connection (For MEX-N5150BT) Connection/Installation Subwoofer* Cautions Run all ground (earth) leads to a common ground (earth) point. Do not get the leads trapped under a screw, or caught in moving parts (e.g., seat railing).
  • Page 22 If the fuse blows to dashboard/center console again after replacement, there may be an internal malfunction. In such a case, consult your nearest Sony dealer. Bracket Bracket Existing parts supplied with your car...

  • Page 23: Disassembly

    MEX-N5100BE/N5100BT/N5150BT SECTION 3 DISASSEMBLY • This set can be disassembled in the order shown below. 3-1. DISASSEMBLY FLOW 3-7. SERVICE POSITION FRONT PANEL SECTION (Page 26) Note: Illustration of disassembly is omitted. 3-2. MINI FUSE (BLADE TYPE) (10A/32V) (FU1), COVER (Page 23) 3-3.

  • Page 24: Sub Panel Assy

    MEX-N5100BE/N5100BT/N5150BT 3-3. SUB PANEL ASSY 2 two claws 3 sub panel assy Note: When installing the sub panel assy, align two ribs and two holes. hole hole 2 two claws 1 two screws (PTT2.6 3-4. CD MECHANISM DECK (MG-101CF-188) Note 1: The service manual of the mechanism deck, used in this model has been issued in a sepa- rate volume.

  • Page 25: Main Board

    MEX-N5100BE/N5100BT/N5150BT 3-5. MAIN BOARD Note 1: When the complete MAIN board is replaced, it is necessary to replace knob (VOL) (SV) assy simultaneously. Also, the destination setting, Bluetooth operation check and Bluetooth information writing is necessary. Refer to “DESTINATION SETTING METHOD” on page 4, “BLUETOOTH FUNCTION CHECKING METHOD USING A CELLULAR PHONE”...

  • Page 26: Service Position

    MEX-N5100BE/N5100BT/N5150BT 3-7. SERVICE POSITION Note 1: The service position below cannot be performed with the fl exible fl at cable (length: 80 mm) used with the unit. Refer to “NOTE OF PERFORMING THE OPERATION CHECK” in the servicing notes, and use a long fl exible fl at cable (length: 150 mm).

  • Page 27: Test Mode

    MEX-N5100BE/N5100BT/N5150BT SECTION 4 TEST MODE SETTING THE TEST MODE Setting method: 1. In the state of source off (the clock is displayed), enter the test mode by pressing the buttons in order of the [ 4] t [MIC 5] t [V ALBUM 1] (press only the [V ALBUM 1] button for two seconds).

  • Page 28: Diagrams

    MEX-N5100BE/N5100BT/N5150BT SECTION 5 DIAGRAMS 5-1. BLOCK DIAGRAM - SERVO/BT/USB Section - CD MECHANISM DECK BLOCK (MG-101CF-188) FL, RL, SUB >002B FPI1 RFRP 27 RFZI DAO3 (Page 29) 17 FPI2 DAO2 R-CH 16 FNI1 DAO4 15 FNI2 DAO1 R-CH DAO5 20 TPI...

  • Page 29: Block Diagram - Main Section

    MEX-N5100BE/N5100BT/N5150BT 5-2. BLOCK DIAGRAM - MAIN Section - INPUT SELECTOR, ELECTRICAL VOLUME IC402 J401 FL, RL, SUB >002B 33 INF1 OUTF1 FRONT (Page 28) R-CH 31 INR1 OUTR1 REAR AUDIO OUT R-CH 30 INS OUTC KEY BOARD (2/3) OUTS AUX_L...

  • Page 30: Block Diagram - Panel/Power Supply Section

    MEX-N5100BE/N5100BT/N5150BT 5-3. BLOCK DIAGRAM - PANEL/POWER SUPPLY Section - RESET SYSTEM CONTROLLER >001B IC503 (3/3) (Page 28) RESET SIGNAL 84 RC_IN1 GENERATOR J801 IC501 (REMOTE IN) 81 RC_IN0 S001 RESET BUFFER Q1307 +1.2V -COM_1.2V REGULATOR BUFFER 115 REMOTE1K Q1308 IC805 REGULATOR +1.5V...
  • Page 31 MEX-N5100BE/N5100BT/N5150BT THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. • Waveforms (In addition to this, the necessary note is printed in each block.) – MAIN Board – For Printed Wiring Boards. For Schematic Diagrams. IC001 es (XTAL_IN) IC503 <zv/ (USB_X2)

  • Page 32: Printed Wiring Boards - Main Section (1/2)

    MEX-N5100BE/N5100BT/N5150BT 5-4. PRINTED WIRING BOARDS - MAIN Section (1/2) - • : Uses unleaded solder. MAIN BOARD (COMPONENT SIDE) (US, CND) C310 C315 C329 C332 IC801 D808 D805 R829 C807 C307 C811 R834 R303 C816 C825 R831 R439 C013 R432...

  • Page 33: Printed Wiring Boards - Main Section (2/2)

    MEX-N5100BE/N5100BT/N5150BT 5-5. PRINTED WIRING BOARDS - MAIN Section (2/2) - • : Uses unleaded solder. MAIN BOARD (CONDUCTOR SIDE) (US, CND) J401 (FRONT VIEW) CN301 AUDIO OUT J1001 J801 REAR FRONT (REMOTE IN) (Except AEP, RU, UK) J001 (ANTENNA IN)

  • Page 34: Schematic Diagram - Main Section (1/4)

    MEX-N5100BE/N5100BT/N5150BT 5-6. SCHEMATIC DIAGRAM - MAIN Section (1/4) - • See page 31 for Waveforms. • See page 38 for IC Block Diagrams. • See page 39 for IC Pin Function Description. MAIN BOARD (1/4) RF_ANT_IN >004S AUDIO_OUT_L AUDIO_OUT_R MAIN...

  • Page 35: Schematic Diagram - Main Section (2/4)

    MEX-N5100BE/N5100BT/N5150BT 5-7. SCHEMATIC DIAGRAM - MAIN Section (2/4) - • See page 38 for IC Block Diagrams. J401 MAIN BOARD (2/4) FRONT AUDIO OUT REAR R439 R440 C405 C408 C411 C414 C418 C419 Q403 Q404 Q405 Q406 Q407 Q408 LTC014TUBFS8TL...

  • Page 36: Schematic Diagram - Main Section (3/4)

    MEX-N5100BE/N5100BT/N5150BT 5-8. SCHEMATIC DIAGRAM - MAIN Section (3/4) - • See page 38 for IC Block Diagrams. (Except AEP, RU, UK) MAIN BOARD (3/4) IC301 REAR RCH (+) CN301 REAR LCH (+) POWER AMP IC301 REAR RCH (–) RR_P PURE5001H-4WX REAR LCH (–)

  • Page 37: Schematic Diagram - Main Section (4/4)

    MEX-N5100BE/N5100BT/N5150BT 5-9. SCHEMATIC DIAGRAM - MAIN Section (4/4) - • See page 31 for Waveforms. • See page 38 for IC Block Diagrams. • See page 39 for IC Pin Function Description. MAIN BOARD (4/4) >010S MAIN BOARD (3/4) (Page 36)
  • Page 38 MEX-N5100BE/N5100BT/N5150BT • IC Block Diagrams – MAIN Board – IC001 SDP2014HN/V102 IC402 BD3468FV-E2 FADER FADER BOOST LEVEL OUTC 32 31 27 26 SHIFT SELECTION FADER FADER BOOST LEVEL VDDA_IFADC 1 OUTS DIGITAL CONTROL DIGITAL SHIFT XTAL OSCILLATION VSSA_IFADC 2 TUNING...
  • Page 39 MEX-N5100BE/N5100BT/N5150BT • IC Pin Function Description MAIN BOARD IC503 R7S7200032CFP (SYSTEM CONTROLLER) Pin No. Pin Name Description BT_MIC_DET External microphone plug insert detection signal input terminal for the Bluetooth AMP_MUTE Amplifi er muting on/off control signal output to the power amplifi er “L”: muting on...
  • Page 40 MEX-N5100BE/N5100BT/N5150BT Pin No. Pin Name Description MEC_LIMIT Limit in detection switch input terminal Power supply terminal (+1.18V) (for internal) Not used MEC_LOAD Loading motor drive signal (loading direction) output terminal “H”: motor on Ground terminal PVcc Power supply terminal (+3.3V) (for I/O)
  • Page 41 MEX-N5100BE/N5100BT/N5150BT Pin No. Pin Name Description Not used USB_ON USB power on/off control signal output to the regulator “H”: power on Power supply terminal (+1.18V) (for internal) Not used Ground terminal RE_ON Jog dial pulse pull-up signal output terminal PVcc Power supply terminal (+3.3V) (for I/O)
  • Page 42 MEX-N5100BE/N5100BT/N5150BT MAIN BOARD IC705 TC94A99FG-003 (SYCH (RF AMP, DIGITAL SERVO PROCESSOR, AUDIO DSP) Pin No. Pin Name Description LPFO PLL circuit low-pass fi lter amplifi er output terminal PVREF PLL circuit reference voltage (+1.65V) terminal VCOF VCO fi lter terminal...
  • Page 43 MEX-N5100BE/N5100BT/N5150BT Pin No. Pin Name Description DAO5 Audio signal (sub-ch) output to the electrical volume DVSS5 Ground terminal VDD1_3 Power supply terminal (+1.5V) VSS_2 Ground terminal XVSS3 Ground terminal System clock input terminal (16.9344 MHz) System clock output terminal (16.9344 MHz) XVDD3 Power supply terminal (+3.3V)

  • Page 44: Exploded Views

    MEX-N5100BE/N5100BT/N5150BT SECTION 6 EXPLODED VIEWS Note: • -XX and -X mean standardized parts, so • The mechanical parts with no reference they may have some difference from the number in the exploded views are not sup- original one. plied. • Items marked “*” are not stocked since •...

  • Page 45: Chassis Section

    MEX-N5100BE/N5100BT/N5150BT 6-2. CHASSIS SECTION (US, CND) not supplied MAIN board not supplied not supplied Note: When the complete MAIN board is replaced, it is necessary to replace knob (VOL) (SV) assy simultaneously. Also, the destination setting, Bluetooth operation check and Blue- tooth information writing is necessary.

  • Page 46: Electrical Parts List

    MEX-N5100BE/N5100BT/N5150BT SECTION 7 MAIN ELECTRICAL PARTS LIST Note: • Due to standardization, replacements in • CAPACITORS When indicating parts by reference num- uF: μF the parts list may be different from the ber, please include the board name. parts specifi ed in the diagrams or the com- •...
  • Page 47 MEX-N5100BE/N5100BT/N5150BT MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C406 1-118-047-11 CERAMIC CHIP 10uF C536 1-116-711-11 CERAMIC CHIP 22uF C408 1-162-923-11 CERAMIC CHIP 47PF C537 1-118-386-11 CERAMIC CHIP 0.1uF C409 1-118-047-11 CERAMIC CHIP 10uF C410...
  • Page 48 MEX-N5100BE/N5100BT/N5150BT MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C747 1-118-386-11 CERAMIC CHIP 0.1uF * C830 1-118-407-11 CERAMIC CHIP 470PF C748 1-118-047-11 CERAMIC CHIP 10uF C831 1-100-769-21 ELECT CHIP 470uF C832 1-118-386-11 CERAMIC CHIP 0.1uF...
  • Page 49 MEX-N5100BE/N5100BT/N5150BT MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C1410 1-118-040-11 CERAMIC CHIP 2.2uF FB702 1-469-084-21 INDUCTOR, FERRITE BEAD (1005) C1411 1-164-866-11 CERAMIC CHIP 47PF FB703 1-469-084-21 INDUCTOR, FERRITE BEAD (1005) C1561 1-116-732-11 CERAMIC CHIP 2.2uF 6.3V...
  • Page 50 MEX-N5100BE/N5100BT/N5150BT MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < TRANSISTOR > R315 1-216-864-11 SHORT CHIP Q401 6-551-970-01 TRANSISTOR LTC614TUFP8T106 R317 1-216-864-11 SHORT CHIP Q402 6-552-922-01 TRANSISTOR LTA014EUBFS8TL R320 1-216-864-11 SHORT CHIP Q403 6-552-937-01 TRANSISTOR...
  • Page 51 MEX-N5100BE/N5100BT/N5150BT MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R526 1-218-941-81 METAL CHIP 1/16W R610 1-218-941-81 METAL CHIP 1/16W R528 1-218-990-81 SHORT CHIP R611 1-218-941-81 METAL CHIP 1/16W R533 1-218-990-81 SHORT CHIP R612 1-218-941-81 METAL CHIP...
  • Page 52 MEX-N5100BE/N5100BT/N5150BT MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R708 1-216-864-11 SHORT CHIP R814 1-218-966-11 METAL CHIP 1/16W R709 1-218-953-11 METAL CHIP 1/16W (US, CND) R815 1-257-321-11 METAL CHIP 0.039 1/2W R711 1-216-864-11 SHORT CHIP...
  • Page 53 MEX-N5100BE/N5100BT/N5150BT MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R878 1-216-296-11 SHORT CHIP R1431 1-218-990-81 SHORT CHIP R890 1-216-864-11 SHORT CHIP R1432 1-218-990-81 SHORT CHIP R892 1-216-864-11 SHORT CHIP R1433 1-216-864-11 SHORT CHIP R1435 1-216-821-11...
  • Page 54 MEX-N5100BE/N5100BT/N5150BT Ref. No. Part No. Description Remark ACCESSORIES ************ 1-489-810-42 REMOTE COMMANDER (RM-X231) (Except AEP, UK, AUS) 4-548-379-11 OPERATING INSTRUCTION (ENGLISH, FRENCH, SPANISH) (US, CND) KEY (FRAME) FITTING FRAME ASSY 4-548-379-21 OPERATING INSTRUCTION (ENGLISH, FRENCH, GERMAN, DUTCH, ITALIAN) (AEP, UK)
  • Page 55 MEX-N5100BE/N5100BT/N5150BT MEMO...
  • Page 56 MEX-N5100BE/N5100BT/N5150BT REVISION HISTORY Ver. Date Description of Revision 2014.12 How to search for a contact point of signal lines or the like in DIAGRAMS SECTION If a contact point of a BLOCK DIAGRAM, PRINTED WIRING BOARD or SCHEMATIC DIAGRAM is shown in a different page, use the PDF fi...

This manual is also suitable for:

Mex-n5100btMex-n5150bt

Table of Contents