Yamaha Virago 750 Installation Manual
  1. Manuals
  2. Brands
  3. Yamaha Manuals
  4. Motorcycle
  5. Virago 750
  6. Installation manual
Yamaha Virago 750 Installation Manual

Yamaha Virago 750 Installation Manual

Motorcycle yamaha virago 750/1100
Hide thumbs

Advertisement

Table of Contents

InstaTrike
By
Installation Manual
Yamaha Virago 750/1100

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Virago 750 and is the answer not in the manual?

Questions and answers

Related Manuals for Yamaha Virago 750

Summary of Contents for Yamaha Virago 750

  • Page 1 InstaTrike Installation Manual Yamaha Virago 750/1100...

  • Page 2: Limited Warranty

    Limited Warranty TOW-PAC, INC. warrants to the first end user purchaser that this product “InstaTrike” when purchased will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product for the period of one year from date of original purchase.
  • Page 3 Notice After your InstaTrike is installed, take some time to get used to “Trike” handling characteristics. On a Trike you will steer rather than lean as you would on a conventional two wheel motorcycle. Take corners very slowly until you get used to the feel of cornering on a Trike.

  • Page 4: Important Notices

    Important Notices InstaTrike is designed for use on paved surfaces only. Use of InstaTrike on unpaved terrain may void warranty. Installation of InstaTrike requires your motorcycle to be level. Some motorcycles are not level when on the center stand. Level the motorcycle by placing spacers under the center stand as needed When installing trailer hitch attach...
  • Page 5 NOTICE: Install all bolts and brackets loosely until all bolts and brackets are in place Remove any aftermarket accessories (saddle bags, back rests, etc) before hitch installation. After installation remount accessories. NOTE: Some aftermarket accessories may not be compatible with InstaTrike hitch. 1) Place motorcycle on a smooth level surface on center stand.
  • Page 6 motorcycle. Located near rear turn signals Use new bolts provided. (10M x 25mm long) It may be necessary to loosen or remove backrest covers or hardware in order to easily access rear frame bolts. After Bracket C and D installation, reattach and/or tighten backrest mounts. 5) Attach Bracket E(left) / F(right) to bottom of Brackets A &...
  • Page 7 INSTALLATION OF THE TOW-PAC HITCH CART.
  • Page 8 1. Place your motorcycle on a smooth flat surface, like a garage floor, and rest it on its center stand. 2. Assemble the axles, tires and wheels, and fenders onto the tow- pac hitch cart. 3. Carefully align the tow-pac hitch cart’s hitch mount with the receiver hitch on the motorcycle.
  • Page 9 Leanstop Braces When installing InstaTrike, bolt leanstop brace to receiver hitch by inserting bolt from bottom through the leanstop brace and washers/spacers. Thread bolt into bracket on hitch and tighten. When removing InstaTrike reverse the above procedure. Adding or removing washers/spacers between receiver hitch and leanstop brace will allow you to level your motorcycle if necessary and adjust traction/handling.
  • Page 10 InstaTrike Assembly Diagram...

  • Page 11: Wheel Alignment

    Wheel Alignment Wheel alignment is critical for proper tire wear and handling. With InstaTrike installed and motorcycle on center stand, measure A and B. Loosen axle plates and align wheel so A and B are equal to within 1/16 of an inch. Tighten axle bolts and torque to 45 pounds.
  • Page 12 Wheel Height / Traction Adjuster The wheel height/traction adjuster (right and left side) allows you to selectively adjust the position of your trike wheels in order to customize ride, handling, level, and traction characteristics. Your trike is shipped with the adjuster preset to an optimum position for your model of motorcycle however you can make whatever adjustments necessary to customize to your bike and personal preference.

  • Page 13: Important Notice

    IMPORTANT NOTICE Periodically check leanstop bolts for tightness. Use enclosed jam nuts on top of bolt to further secure leanstop bolt.
  • Page 14 Periodically check alignment plate bolt for tightness as well. (behind receiver) Fender Installation Instructions (12 Inch wheel only) 1) Attach fender brackets to trike frame with spacers BETWEEN fender bracket and frame. Tighten. NOTE: Leave fender bolts loose until all bolts are inserted. 2) Place gray plastic washers between fender and trike frame/fender bracket.
  • Page 15 Reflector Mounting Instructions Be sure fender is clean and free from dust Do not apply reflectors in direct sunlight or on a hot surface Remove backing from reflector and carefully position on fender. See Diagram Below Lightly spraying back of reflectors with a mild solution of water or Windex will allow easier positioning.

This manual is also suitable for:

Virago 1000

Table of Contents