Related Manuals for Mira Advance ATL J97A
Summary of Contents for Mira Advance ATL J97A
- Page 1 Mira Advance ATL ADJUSTABLE TEMPERATURE LIMIT THERMOSTATIC 9.0 and 9.8 kW For SPARES, ADVICE or REPAIRS Please call us on 0844 571 5000 (UK Only) Important! This product is suitable for mains fed cold water only. Installation Guide...
-
Page 2: Table Of Contents
Memory Model ..................25 If you experience any difficulty with the installation or operation of your new Electric Shower, then please refer to 'Fault Diagnosis', before contacting Mira Showers. Our contact details can be found on the back cover of this guide. - Page 3 Fault Diagnosis ..................25 1. Installer Troubleshooting Guide............26 2. Diagnostic Procedure ..............27 BEAB Care In-Service Tests ..............32 Maintenance ................... 35 Spare Parts and Accessories ............... 36 Wiring Diagram ..................38 Customer Service ..............Back Cover...
-
Page 4: Shower Models
C h e l t e n h a m G L 5 2 5 E P Guarantee For domestic installations, Mira Showers guarantee the Mira Advance ATL against any defect in materials or workmanship for a period of two years from the date of purchase (shower fittings for one year). -
Page 5: Patents And Design Registration
Recommended Usage Domestic Light Commercial Heavy Commercial Healthcare Patents and Design Registration Design Registration: 000738141: 0003, 0006, 0007, 0009 Patents: GB: 2269466, 2270370, 2298478, 2298479, 2298481 IMPORTANT SAFETY INFORMATION Installation must be carried out in accordance with these instructions, and must be conducted by designated, qualified and competent personnel. -
Page 6: Caution
12. DO NOT fit any form of outlet flow control (e.g. trigger handsets) as the outlet acts as a vent for the tank body. Only Mira recommended outlet fittings should be used. 13. This product is not suitable for areas with high humidity (i.e. steam rooms). -
Page 7: Pack Contents
PACK CONTENTS Tick the appropriate boxes to familiarise yourself with the part names and to confirm that the parts are included. 1 x Mira Advance ATL 1 x Mira Advance ATL 1 x Mira Advance ATL Memory Flex or Flex Extra Standard or Standard Extra (Instantmatch by Whale®... -
Page 8: Specifications
The BEAB Care mark is invalid if the product is not installed and used in accordance with the manufacturer's specifications and instructions. The Mira Advance ATL Flex Extra Wireless (J97P) is in compliance with the essential requirements and other relevant provisions of the R&TTE directive 1999/5/EC. A copy of the declaration of conformity may be obtained by contacting Kohler Mira Ltd UK customer services department. -
Page 9: Dimensions
Dimensions 87.5 mm 102 mm 71 mm 71 mm 184 mm 184 mm Advance ATL Advance ATL Flex / Flex Extra / Standard / Memory Flex Extra Wireless INSTALLATION REQUIREMENTS General We recommend that the product be brought into the room where it is to be installed and left to acclimatise to room temperature, this will reduce the possibility of condensation on electronic components. - Page 10 1.4 Avoid layouts where the shower hose will be sharply kinked. This may reduce the life of the hose. 1.5 Supply pipework MUST be flushed to clear debris before connecting the appliance. Debris will reduce the performance of the shower and may damage the product.
-
Page 11: Electrical
Refer to section: 'Important Safety Information' first. 2.1 In a domestic installation, the rating of the electricity supplier’s fuse and the consumer unit must be adequate for the additional demand. All Mira Advance ATL electric showers are high power appliances. Voltage drop due to local heavy demand will reduce the shower’s performance. - Page 12 Connector Lead Sockets for the Flow Valve Turbine and Inlet Sensor, and the Tank Assembly Sensor. Terminal Block Drain Pump PCB (Mira Advance 'Extra' models only) Inlet Clamp Air Bleed Button Wire 75 Earth Flow Valve Ribbon Cable (connect to front Cover).
-
Page 13: Installation
INSTALLATION Refer to section: 'Important Safety Information' first. This installation covers all models of the Mira Advance ATL Thermostatic shower. Decide on shower position, 100 mm leaving adequate space for maintenance. (If installation includes an Instantmatch by Whale® drain pump, see "Wireless"... -
Page 14: Priming The Shower
Required Fixing Hole Optional Optional 1083677-W7-A © Kohler Mira Limited, May 2007 9. Caution! Do not drill 10. Use template provided 11. Drill holes through into buried cables or t o m a r k a n d d r i l l p l a s t i c c a s e a s pipes. - Page 15 N = BLUE E = GREEN L = BROWN F e e d c a b l e i n t o 17. Refit splash guard. 18. Connect ribbon cable case. Firmly connect to inside of cover. conductors. DO NOT exert strain on terminal block.
-
Page 16: Mira Advance Shower Models For Use With The Instantmatch By Whale® Digital Pump
Mira Advance Shower Models for use with the Instantmatch by Whale® Digital Pump For use with the Whale Instant Match Pump Wireless Standard Extra Flex Extra Flex Extra Wireless J97G* J97H* J97P* Instant Match For use with the Whale Instant Match... -
Page 17: Electrical Schematic Diagram (Drain Pump)
Supply cable Consumer Unit 45 Amp Double-pole Isolating Switch Optional Outlet Unswitched Double Checkvalve Spur Isolating Instant Match Valve Transformer Mains Fed Cold Water Supply Signal Cable Connector Instantmatch (Optional) by Whale® Pump Electrical Schematic Diagram (Drain Pump) -
Page 18: Instantmatch By Whale® Digital Pump
Instantmatch by Whale® Digital Pump The Mira Advance ATL 'Extra' models can be connected to the Instantmatch by Whale® Pump. This section describes how to identify and connect the shower to the drain pump. For full installation instructions of the Instantmatch by Whale® Pump, see separate guide. -
Page 19: Wireless Installation
Wireless Installation (Flex Extra Wireless J97P model only) The wireless version of the Instantmatch by Whale® Pump is connected to the Mira Advance ATL 'Extra' Wireless shower model with a radio signal. For optimum signal strength, site the pump transformer as close to the shower as possible. -
Page 20: Drain Pump Registration
Drain Pump Registration (Flex Extra Wireless J97P model only) The shower must register a wireless signal to the drain pump then establish a reliable connection. If you encounter difficulty registering the shower to the drain pump, make sure all electronic devices that could be causing signal interference are temporarily switched off. -
Page 21: Registration Or Test Failure
6. Press START/STOP. 7. Shower will START. 8. Pump will START. Any delay will depend upon the plumbing layout, but pump should start within 10 SECONDS. 9 . Pump and shower work normally. A test failure is indicated by the following: •... -
Page 22: Basic Post Installation Checks
Basic Post Installation Checks 1. Turn on electrical 2. Power to appliance, 3. Temperature to full supply. check Start/Stop for cold. blue light. 5 secs 4. Start shower to test for 5. If there is no water 6. Push Start/Stop to water flow. -
Page 23: Commissioning
COMMISSIONING On initial installation, the appliance needs to 'learn' about the site conditions and does so during the commissioning cycle. Once set, the shower constantly updates it's memory with information about the site conditions to deliver the best performance. DO NOT commission the appliance if water leaks from the unit. Set Maximum Temperature and Commissioning Cycle 1. -
Page 24: Commissioning Failures
1st Beep (LONG) - Release START/STOP. 2nd Beep (SHORT) - Release FLOW. 5. HIGH FLOW LIGHT FLASHES This indicates shower is commissioning correctly. Water flows for approximately 1 minute 20 seconds. In some cases the cycle can take up to 3 minutes. Allow shower to stop automatically. -
Page 25: Beab Care
If the maximum temperature is adjusted after it has been stored in one or more of the memory buttons (refer to section: 'Operation, Storing the Memory Presets' in the 'Mira Advance ATL User Guide'), then the showering temperature cannot exceed the new maximum setting. -
Page 26: Fault Diagnosis
FAULT DIAGNOSIS 1. Installer Troubleshooting Guide Refer to section: 'Important Safety Information' first and refer also to 'User Trouble Shooting Guide'. The following troubleshooting solutions may require the removal of the cover of the shower. The cover should only be removed by a competent tradesperson and when doing so they should be aware of the following: •... -
Page 27: Diagnostic Procedure
2. DIAGNOSTIC PROCEDURE Ensure the shower pullcord / isolator switch is in the OFF position, then turn ON the pullcord / isolator switch. If the unit ‘Beeps’ & the Start / Stop button is flashing WAIT for 20 SECONDS until the button stops flashing. NOTE! If the Start / Stop button continues to flash &... - Page 28 Advance Error Codes / Display, Causes and Rectification All fault codes will require the shower to be turned off at the pullcord / isolator switch to reset the unit. When the pullcord / isolation switch is turned back on the shower may beep and the Start / Stop button may flash.
- Page 29 Incoming water temperature too high. Check inlet water temperature is not too high. (E.g. pipework runs alongside hot pipe). Replace Flow Valve. Replace Control PCB / Cover. If the unit is an 'Extra' or 'Flex Extra' model, replace the Drain Pump PCB. Flow Valve Assembly is disconnected or faulty.
- Page 30 Unsafe hot water detected. Unit incorrectly shut down causing hot water to trip the max temp limit, this would be following ERROR 17. Hot water in the heater tank, bleed via the blue button. Check Outlet Sensor connection to the Relay Board.
- Page 31 For drain pump only: Advance 'Extra' models Drain Pump not communicating with Shower. Check power to Drain Pump. Check connection between Drain Pump and Shower. If wireless, reregister the signal and retest using the procedure in this guide, see 'Drain Pump Registration'. Wireless Channels.
-
Page 32: Beab Care In-Service Tests
Please record all test results on this form, including details of all measurement equipment used. This form is available to download at www.mirashowers.co.uk. 1178847-W9-B © Kohler Mira Limited, August 2011 If there is no significant change in the outlet water temperature greater than ±1 ºC between the two inspections, the in-service test frequency may be reduced but must not exceed 12 months between any two inspections. - Page 33 Run the shower with the temperature control set to full cold and the flow set to high for 2 - 3 minutes and then stop the shower. Isolate the electrical and water supplies. For falling supplies, remove the inlet filter (see Maintenance) and use a cup or suitable container to catch a small quantity of water that will flow from the inlet connector as the filter is removed.
-
Page 35: Maintenance
MAINTENANCE Tradesperson Maintenance - Inlet Filter Cleaning/Replacing Read the section 'Important Safety Information' first. 1. Electrical and water supplies to 2. Remove cover screw, cover and appliance are turned off. splash guard. Disconnect ribbon cable from cover 3. Hold a spanner or other suitable grips 4. -
Page 36: Spare Parts And Accessories
Warning! In the interests of safety, spares requiring exposure to mains voltage should only be fitted by competent persons. Accessories Drain Pump Cable 1.1759.125 A cable to connect the Mira Advance to the Instantmatch by Whale® Pump. Includes fitting instructions. Suitable for the following models: Mira Advance Standard Extra. - Page 37 1643.104 1643.103 1643.112 1643.105 1643.144 1829.063 1643.100 1829.062 416.38 1643.101 1643.102 1643.114 1643.251 1643.252 1643.255 1643.262 1643.105 1643.144...
-
Page 38: Wiring Diagram
WIRING DIAGRAM (Fitted to Standard Extra and Flex Extra models only.) Control Board Radio CN10 CN12 Relay CN11 Board 230/240 V AC Only Outlet Temperature Sensor Pump Driver Board One Shot Thermal Switch Heater Tank (Fitted to Standard Extra and Flex Extra models only.) - Page 39 NOTES...
-
Page 40: Customer Service
The product must be installed and maintained in Spares and Accessories - We hold the largest accordance with the instructions given in this user stocks of genuine Mira spares and accessories. guide. Contact us for a price or visit our website to...
Need help?
Do you have a question about the Advance ATL J97A and is the answer not in the manual?
Questions and answers