Height measurement includes feet and chassis. All features and specifications are subject to change without notice. Harman Kardon is a registered trademark, and Power for the digital revolution is a trademark, of Harman International Industries, Inc. is a trademark of Harman International Industries, Inc.
• Amplifier is in protection mode • Contact your local Harman Kardon service center, which you can due to internal problems locate by visiting our Web site at www.harmankardon.com No sound from surround or •...
Page 4
AMPLIFIER SECTION BIAS ADJUSTMENT Measurement condition . No input signal or volume position is minimum. Standard value. ± . Ideal current = 48mA ( ± . Ideal DC Voltage = 21.12mV ( CUP11517X (MAIN PCB) CN63 CN61 CN62 CN65 CN64 VR63 VR65 VR64...
Page 6
n Block Diagram DZFL1 AK4356 Audio LOUT1+ DATT LOUT1- MCLK MCKO DZFR1 LRCK Controller LRCK ROUT1+ DATT BICK ROUT1- BICK DZFL2 LOUT2+ DATT Control LOUT2- CCLK Register DZFR2 CDTI ROUT2+ DATT ROUT2- DZFL3 LRCK LOUT3+ DATT LOUT3- BICK DZFR3 SDTI1 SDOUT1 ROUT3+ SDTI2...
Page 12
DIR IC PIN FUNCTION (AK4114VQ) : IC75 PIN/FUNCTION Pin Name Function IPS0 Input Channel Select 0 Pin in Parallel Mode Receiver Channel 4 Pin in Serial Mode (Internal biased pin) No Connect NC(AVSS) No internal bonding. This pin should be connected to AVSS. DIF0 Audio Data Interface Format 0 Pin in Parallel Mode Receiver Channel 5 Pin in Serial Mode (Internal biased pin)
Page 13
PIN/FUNCTION (Continued) Pin Name Function Power-Down Mode Pin When “L”, the AK4114 is powered-down and reset. Master Clock Operation Mode 0 Pin in Parallel Mode CDTO Control Data Output Pin in Serial Mode, IIC= “L”. CAD1 Chip Address 1 Pin in Serial Mode, IIC= “H”. Master Clock Operation Mode 1 Pin in Parallel Mode CDTI Control Data Input Pin in Serial Mode, IIC= “L”.
August 1984 Revised January 2000 Quad Analog Switch (74HC4066D) : IC42 General Description Features The MM74HC4066 devices are digitally controlled analog Typical switch enable time: 15 ns switches utilizing advanced silicon-gate CMOS technology. Wide analog input voltage range: 0–12V These switches have low “ON” resistance and low “OFF” Low “ON”...
Page 19
A/D CONVERTER IC PIN FUNCTION (AK5380VT) : IC77 PIN/FUNCTION Pin Name Description AINR Rch Analog Input Pin AINL Lch Analog Input Pin NC Pin No internal bonding. VCOM Common Voltage Output Pin Normally connected to AGND with a 0.1µF ceramic capacitor in parallel with an electrolytic capacitor less than 2.2µF.
Page 20
Sheet 4/5 Ise Electronics Corporation :Grid Assignment CM2054C Scale 3:1 Unit : mm G3-G10...
Page 22
AUDIO DSP (CS493263 - CLG : IC79) PIN No. Pin Name Function 1,12,23 +VD1 Digital Power supply. Normally +2.5v 2,13,24 DGND Digital Ground AUD3 SPDIF transmitter output/Digital audio output(N.C) Host write strobe pin(connected to GND with an external resistor) Host parallel output enable pin(pulled up with an external resistor) CS_DA SPI Serial data input pin CS_CK...
Page 24
Ordering number : *EN5039 CMOS IC LC74763, 74763M On-Screen Display LSI Preliminary Overview Package Dimensions The LC74763 and LC74763M are on-screen display unit: mm CMOS LSIs that superimpose text and low-level 3196-DIP30SD graphics onto a TV screen (video signal) under the [LC74763] control of a microcontroller.
Page 25
LC74763, 74763M Pin Functions Pin No. Symbol Function Description Ground Ground connection Xtal Connection for the crystal and capacitor used to form the crystal oscillator that generates Crystal oscillator connection the internal synchronization signal. The oscillator can be selected with a command switch. Xtal OUT1 Horizontal synchronization...
Page 26
LC74763, 74763M Pin Assignment Top view Serial Data Input Timing No. 5039-4/19...
Page 27
LC74763, 74763M System Block Diagram No. 5039-5/19...
Page 28
PIN ASSIGNMENT (TOP VIEW) Top view No. 5606-3/13...
BLOCK DIAGRAM VFD DRIVER IC PIN FUNCTION (LC75725E) : IC74 Pin No. Function Handling when unused 1, 13 Driver block power supply connection. (Both pins must be connected.) — — Logic block power supply connection. Provide a voltage between 4.5 and 5.5 V. —...
Page 31
M-COM IC PIN ASSIGNMENT & BLOCK DIAGRAM PIN ASSIGNMENT (TOP VIEW) P 20/A16 P 21/A17 P22/A18 P57/CLK P23/A19 RSTX P24/A20/PPG0 P56/RDY P 25/A21/PPG1 P55/HAKX P26/A22/PPG2 P54/HRQ P27 /A23/PPG3 P53/WRHX P30 /A00/AIN0 P52/WRLX P 31/A01/BIN0 P51/RDX P50/ALE P32/A02/ZIN0 PA3/OUT3 P33 /A03/AIN1 PA2/OUT2 P 34/A04/BIN1 PA1/OUT1...
Page 32
IC PIN FUNCTION (M-COM : MB90F476APFG) : IC72 LQFP Pin Name Circuit Type Function Oscillator pin Oscillator pin 32 kMHz Oscillator pin 32 kMHz Oscillator pin RSTX Reset input pin General-purpose I/O ports P00 to P07 A pull-up resistor can be attached using the pull-up resistor setting register (RDR0) (RD07 to RD00 = 1).
Page 33
LQFP Pin Name Circuit Type Function General-purpose I/O ports In the external bus mode, the pin functions as an external address pin. (CMOS/H) AIN0 The pin is an 8-/16-bit up-and-down timer input pin (ch0). General-purpose I/O port In the external bus mode, the pin functions as an external address pin. (CMOS/H) BIN1 The pin is the 8-/16-bit up-and-down timer input pin (ch0).
Page 34
LQFP Pin Name Circuit Type Function General-purpose I/O port In the external bus mode, the pin functions as ALE pin. (CMOS) In the external bus mode, the pin functions as an address capture enable signal (ALE) pin. General-purpose I/O port In the external bus mode, the pin functions as the RDX pin.
Page 35
LQFP Pin Name Circuit Type Function General-purpose I/O port (CMOS) SOT0 The pin functions as an UART data output pin. General-purpose I/O port SCK0 (CMOS/H) The pin functions as an UART clock I/O pin. General-purpose I/O port TIN0 (CMOS/H) The pin functions as the event input pin of the 16-bit reload timer. General-purpose I/O port TOT0 (CMOS/H)
Page 39
RDS demodulator (SAA6579TV1) : IC71 BLOCK DIAGRAM handbook, full pagewidth 82 pF 47 pF +5 V 4.332/8.664 MHz 2.2 k Ω 0.1 µF OSCI OSCO ANTI- 57 kHz OSCILLATOR QUAL signal RECONSTRUCTION QUALITY BIT ALIASING BANDPASS FILTER GENERATOR FILTER 330 pF (8th ORDER) DIVIDER SCOUT...
Page 40
PIN FUNCTION & PIN ASSIGNMENT PINNING SYMBOL DESCRIPTION QUAL quality indication output RDDA RDS data output reference voltage output (0.5V multiplex signal input +5 V supply voltage for analog part ground for analog part (0 V) subcarrier input to comparator SCOUT subcarrier output of reconstruction filter MODE...
Need help?
Do you have a question about the AVR 3550 and is the answer not in the manual?
Questions and answers