Table of Contents
Advertisement
Quick Links
CDX-GT800D/GT805DX
SERVICE MANUAL
Ver. 1.0 2005.12
• The tuner and CD sections have no adjustments.
AUDIO POWER SPECIFICATIONS (US MODEL)
POWER OUTPUT AND TOTAL HARMONIC DISTORTION
23.2 watts per channel minimum continuous average power into
4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more
than 5% total harmonic distortion.
CD player section
Signal-to-noise ratio
120 dB
Frequency response
10 – 20,000 Hz
Wow and flutter
Below measurable limit
Tuner section
FM
Tuning range
CDX-GT805DX: 87.5 – 107.9 MHz
CDX-GT800D: 87.5 – 108 MHz
Antenna terminal
External antenna connector
Intermediate frequency
10.7 MHz/450 kHz
Usable sensitivity
9 dBf
Selectivity
75 dB at 400 kHz
Signal-to-noise ratio
67 dB (stereo), 69 dB (mono)
Harmonic distortion at 1 kHz
0.5% (stereo), 0.3% (mono)
Separation
35 dB at 1 kHz
Frequency response
30 – 15,000 Hz
AM (CDX-GT805DX)
Tuning range
530 – 1,710 kHz
Antenna terminal
External antenna connector
Intermediate frequency
10.7 MHz/450 kHz
Sensitivity
30 µV
MW/LW (CDX-GT800D)
Tuning range
MW: 531 – 1,602 kHz
LW: 153 – 279 kHz
Antenna terminal
External antenna connector
Intermediate frequency
10.7 MHz/450 kHz
Sensitivity
MW: 30 µV
LW: 40 µV
Sony Corporation
9-879-999-01
eVehicle Division
2005L04-1
Published by Sony Engineering Corporation
© 2005.12
Photo: CDX-GT805DX
Model Name Using Similar Mechanism
CD Drive Mechanism Type
Optical Pick-up Name
SPECIFICATIONS
Power amplifier section
Outputs
Speaker impedance
Maximum power output 52 W × 4 (at 4 ohms)
General
Outputs
Inputs
Loudness
FM/AM COMPACT DISC PLAYER
FM/MW/LW COMPACT DISC PLAYER
US Model
CDX-GT805DX
E Model
Chinese Model
CDX-GT800D
NEW
MG-611WD-186//Q
KSS1000E
Speaker outputs (sure seal connectors)
4 – 8 ohms
Audio outputs terminal (front/rear)
Subwoofer output terminal (mono)
Power antenna relay control terminal
Power amplifier control terminal
Telephone ATT control terminal
Illumination control terminal
BUS control input terminal
BUS audio input/AUX IN terminal
Remote controller input terminal
Antenna input terminal
+8 dB at 100 Hz
+0 dB at 10 kHz
– Continued on next page –
CDX-GT805DX
CDX-GT800D
Advertisement
Table of Contents
Related Manuals for Sony CDX-GT800D
Summary of Contents for Sony CDX-GT800D
- Page 1 General Outputs Audio outputs terminal (front/rear) Tuning range CDX-GT805DX: 87.5 – 107.9 MHz Subwoofer output terminal (mono) CDX-GT800D: 87.5 – 108 MHz Power antenna relay control terminal Antenna terminal External antenna connector Power amplifier control terminal Intermediate frequency 10.7 MHz/450 kHz...
- Page 2 COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
- Page 3 CDX-GT800D/GT805DX • CD Playback: NOTE FOR THE OPENING OF THE FRONT PANEL You can play CD-DA (also containing CD TEXT* ), CD-R/CD- In this set, the front panel is lowered to below the bottom face when RW (MP3/MWA files also containing Multi Session and ATRAC it is opened.
-
Page 4: Table Of Contents
CDX-GT800D/GT805DX • UNLEADED SOLDER TABLE OF CONTENTS Boards requiring use of unleaded solder are printed with the lead- free mark (LF) indicating the solder contains no lead. GENERAL (Caution: Some printed circuit boards may not come printed with Location of Controls ............5 the lead free mark due to their particular size.) -
Page 5: General
SECTION 1 This section is extracted GENERAL from instruction manual. • LOCATION OF CONTROLS • CDX-GT800D Location of controls and basic operations Main unit H Z (eject)/ANGLE button 5 qk DSPL (display)/PTY (Programme To eject the disc/slide down the front panel Type) button 8, 10 (press);... -
Page 6: Connections
CDX-GT800D/GT805DX • CONNECTIONS • CDX-GT800D • CDX-GT805DX Connection example Notes (2- A ) • Be sure to connect the ground lead before connecting the AUDIO OUT amplifi er. FRONT • The alarm will only sound if the built-in amplifi er is used. - Page 7 CDX-GT800D/GT805DX • CDX-GT800D...
- Page 8 CDX-GT800D/GT805DX • CDX-GT805DX Source selector (not supplied) Sélecteur de source Supplied with the CD/MD changer (non fourni) Fourni avec le changeur de CD/MD Selector de fuente Suministrado con el cambiador de CD/MD (no suministrado) XA-C30 BUS AUDIO IN /AUX IN...
-
Page 9: Disassembly
CDX-GT800D/GT805DX SECTION 2 DISASSEMBLY Note: This set can be disassemble according to the following sequence. 2-1. BASE PANEL ASSY (Page 10) 2-2. SUB PANEL ASSY (Page 10) 2-3. CD MECHANISM BLOCK (Page 11) 2-4. DRIVING SECTION 2-13. SERVO BOARD (DB-F05) 2-7. -
Page 10: Base Panel Assy
CDX-GT800D/GT805DX Note: Follow the disassembly procedure in the numerical order given. 2-1. BASE PANEL ASSY 2 two screws (panel F) 5 bracket (PWB) 7 base panel assy 1 two screws (panel F) 8 FLEXIBLE board (27 core) (CN607) (Take care not to pull the... -
Page 11: Cd Mechanism Block
CDX-GT800D/GT805DX 2-3. CD MECHANISM BLOCK 5 CD mechanism block 6 two screws (+PTT 2.6 × 6) 7 bracket (CD) 2 screw (+PTT 2.6 × 6) 4 CNP301 1 screw (+PTT 2.6 × 6) 2-4. DRIVING SECTION (DB-F05) 3 screw (+PTT 2.6 × 6) -
Page 12: Follow Move (F) Assy, Driving (F) Assy
CDX-GT800D/GT805DX 2-5. FOLLOW MOVE (F) ASSY, DRIVING (F) ASSY To install the assembly, turn the gear (cam LF5) and align the detent with the holes A . gear (cam LF5) 6 joint 2 follow move (F) assy 5 driving (F) assy... -
Page 13: Chassis (T) Sub Assy
CDX-GT800D/GT805DX 2-7. CHASSIS (T) SUB ASSY 4 claw 2 two screws (+P 1.7 × 2.2) 1 two screws (+P 1.7 × 2.2) 6 chassis (T) sub assy 5 SENSOR board 3 claw 2-8. ROLLER ARM ASSY 3 washer 5 roller arm assy... -
Page 14: Chassis (Op) Assy
CDX-GT800D/GT805DX 2-9. CHASSIS (OP) ASSSY qa chassis (OP) assy 0 coil spring (damper) lever (D) 4 washer 1 optical pick-up (16 core) (CN1) 9 two coil springs (damper) 5 gear (LE1) slider (R) 3 tension coil spring (KF60) 2 Remove the six solders. -
Page 15: Sl Motor Assy (M902)
CDX-GT800D/GT805DX 2-11. SL MOTOR ASSY (M902) 1 screw (+P 1.4 × 1.8) 2 SL motor assy (M902) 2-12. LE MOTOR ASSY (M903) 8 screw 0 gear (LE) assy (+M 1.7 × 2.5) 9 bearing (LEB-N) 2 washer qa screw (+M 1.7 × 2.5) -
Page 16: Servo Board
CDX-GT800D/GT805DX 2-13. SERVO BOARD 6 SERVO board 1 Remove the eight solders. 2 Remove the three solders. 4 screw 5 claw 3 optical pick-up (16 core) (CN1) -
Page 17: Diagnosis Function
CDX-GT800D/GT805DX SECTION 3 DIAGNOSIS FUNCTION Description of the Diagnostics function: 4. Contents of each display mode 4-1. Reset count display mode 1. Setting the Diag display mode D I A G With the power off, press the [4] button, [5] button, and [4] button on the set body or the remote control (for more than 2 seconds) in turn. - Page 18 CDX-GT800D/GT805DX 4-5. CD error information display mode 4-6. OFFSET/FAILURE error display mode 4-5-1. Error description D I A G Y X X X X X D I A G Operating hours Error information Error description Error description Indication Description (in hexadecimal...
-
Page 19: Diagrams
CDX-GT800D/GT805DX SECTION 4 DIAGRAMS 4-1. BLOCK DIAGRAM — CD SECTION — D/A, A/D CONVERTER IC801 DETECTOR IC471 FPI2 AOUT1 (P07) AGCI RFEQO SDIN0 AUXL1 RFRPI BCK (P08) BCLK0 AUXR1 R-CH FNI2 LRCK (P09) LRCLK0 VOUT1 MAIN FPI1 X801 VOUT2 R-CH... -
Page 20: Block Diagram -Main Section
CDX-GT800D/GT805DX 4-2. BLOCK DIAGRAM — MAIN SECTION — IN/OUT SELECT, ELECTRIC VOLUME IC401 30 FL-IN R-CH 32 FR-IN PRE AMP IC402 31 RL-IN PJ401(2/2) SECTION 33 RR-IN R-CH (Page 19) 16 SUB1 FL-OUT 5 RL+ OUT(RL) AUDIO OUT 14 L-OUT... -
Page 21: Block Diagram -Display Section
CDX-GT800D/GT805DX 4-3. BLOCK DIAGRAM — DISPLAY SECTION — FL DISPLAY DRIVE IC901 SYSTEM CONTROL LAT_TA2_OUT IC303 (3/3) FL_DAT1 FL_DAT2 RE_1A # NC ROTARY FL_DAT3 RE_1B # NC ENCODER FL_CLK 78 RE_2A # NC S906(1/2),911(1/2) FL_CLK_IN 5 77 RE_2B # NC... -
Page 22: Circuit Boards Location
CDX-GT800D/GT805DX 4-4. CIRCUIT BOARDS LOCATION • NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is SERVO board SENSOR board printed in each block.) For schematic diagrams. -
Page 23: Printed Wiring Boards -Cd Mechanism Section
CDX-GT800D/GT805DX 4-5. PRINTED WIRING BOARDS — CD MECHANISM SECTION — • Refer to page 22 for Circuit Boards Location. : Uses unleaded solder. TP39 TP38 TP26 TP24 TP41 FMB3 FMA6 TP23 TP29 TP42 TP43 TP45 TP27 TP44 TP37 TP46 TP53... -
Page 24: Schematic Diagram -Cd Mechanism Section (1/2)
CDX-GT800D/GT805DX 4-6. SCHEMATIC DIAGRAM — CD MECHANISM SECTION (1/2) — • Refer to page 22 for Waveforms. TP33 TP32 TP31 TP52 TP38 TP39 TP53 R132 C132 R133 TP41 C133 TP50 R29 R19 TP51 TP21 TP22 TP49 TP23 TP24 TP25 TP26... -
Page 25: Schematic Diagram -Cd Mechanism Section (2/2)
CDX-GT800D/GT805DX • Refer to page 22 for Waveform. • Refer to page 36 for IC Block Diagram. 4-7. SCHEMATIC DIAGRAM — CD MECHANISM SECTION (2/2) — • Refer to page 41 for IC Pin Descriptions. (Page 24) (Page 30) TP74... -
Page 26: Printed Wiring Boards -Main Section
CDX-GT800D/GT805DX 4-8. PRINTED WIRING BOARDS — MAIN SECTION — • Refer to page 22 for Circuit Boards Location. : Uses unleaded solder. • Semiconductor Location Ref. No. Location Ref. No. Location D101 C-10 IC303 D102 C-10 IC402 D103 C-10 IC470... - Page 27 CDX-GT800D/GT805DX PJ401 CN401 AUDIO OUT SUB OUT CNJ101 (MONO) AUDIO ON REAR FRONT (REMOTE IN) PJ501 (ANTENNA) –1 –2 –3 –4 –5 –6 CNP102 (BUS CONTROL IN) CNP102 (SHASSIS) CNP101 Q408 C227 C491 C232 C228 C288 C188 C178 C278 C215...
-
Page 28: Schematic Diagram -Main Section (1/4)
CDX-GT800D/GT805DX • Refer to page 22 for Waveforms. 4-9. SCHEMATIC DIAGRAM — MAIN SECTION (1/4) — • Refer to page 35 for IC Block Diagrams. C470 C424 IC B/D R474 R470 TUX501 C419 C420 C421 R478 C474 R411 R410 C409... -
Page 29: Schematic Diagram -Main Section (2/4)
CDX-GT800D/GT805DX 4-10. SCHEMATIC DIAGRAM — MAIN SECTION (2/4) — • Refer to page 37 for IC Block Diagrams. CN401 C411 FB402 R403 C442 C403 C443 R402 R408 C215 C210 C228 C205 C227 Q470 C278 R409 IC B/D C178 R407 C412... -
Page 30: Schematic Diagram -Main Section (3/4)
CDX-GT800D/GT805DX • Refer to page 22 for Waveforms. • Refer to page 39 for IC Block Diagram. 4-11. SCHEMATIC DIAGRAM — MAIN SECTION (3/4) — • Refer to page 43 for IC Pin Descriptions. (Page 28) (Page 29) D906 D904... -
Page 31: Schematic Diagram -Main Section (4/4)
CDX-GT800D/GT805DX 4-12. SCHEMATIC DIAGRAM — MAIN SECTION (4/4) — • Refer to page 40 for IC Block Diagrams. (Page 28) (Page 29) Q301 R116 CNJ101 JR613 C112 R625 R319 R318 Q642 L304 Q624 CN606 C622 L620 C342 C340 Q623 Q302... -
Page 32: Printed Wiring Boards -Panel Section
CDX-GT800D/GT805DX 4-13. PRINTED WIRING BOARDS — PANEL SECTION — • Refer to page 22 for Circuit Boards Location. : Uses unleaded solder. R991 R990 LED990 (DISC IN) S901 CN901 S902 (FRONT PANEL DETECT) RESET MAIN BOARD (Page 26) DISPLAY BOARD... -
Page 33: Printed Wiring Board -Display Section
CDX-GT800D/GT805DX 4-14. PRINTED WIRING BOARD — DISPLAY SECTION — • Refer to page 22 for Circuit Boards Location. : Uses unleaded solder. S903 S908 LED906 LED908 R904 LED905 LED907 S910 S904 R903 IC903 S909 S907 LED909 LSW906 LSW905 LSW904 S905... -
Page 34: Schematic Diagram -Display Section
CDX-GT800D/GT805DX • Refer to page 22 for Waveform. 4-15. SCHEMATIC DIAGRAM — DISPLAY SECTION — • Refer to page 45 for IC Pin Descriptions. R934 R933 R931 R930 R922 R920 R928 R926 R924 S908 LED903 LED901 LSW905(2/2) LSW903(2/2) LSW901(2/2) R907... -
Page 35: Ic Block Diagrams
CDX-GT800D/GT805DX • IC BLOCK DIAGRAMS IC801 ADAU1421YSTZ (MAIN Board (1/4)) 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 FILTA VREF VOUT3 A-GND 59 VOUT2 58 VOUT1 AVDDD1 57 AUXR1 56 AUXL1 55 AVDD3... - Page 36 CDX-GT800D/GT805DX IC650 NJM2379V (MAIN Board (1/4)) 30µA VREF U.VLO S.C.P ER.AMP 0.52V IC1 BA5968FP-E2 (SERVO Board (2/2)) OPIN4+ LDCTL OUTR OUTF OPIN4– OPOUT1 OPOUT4 OPIN3+ OPIN3– OPOUT2 OPOUT3 POWVCC MUTE MUTE VOL– VOL+ VOL+ VOL2– VOL3– LEVEL LEVEL SHIFT SHIFT...
- Page 37 CDX-GT800D/GT805DX IC551 TDA7333013TR (MAIN Board (1/4)) BAND PASS SINC4 SIGMA DELTA INTERPOLATOR FILTER FILTER CONVERTER VDDA INTN REF3 SDAOUT REF2 SDAIN RDSREG BUFFER TEST LOGIC REF1 INTN SA_DATAOUT C/SPI DEMODULATOR & & & INTERFACE SDA_DATAIN SYNCHRONIZATION CONTROL PIN MUX'S TESTREG...
- Page 38 CDX-GT800D/GT805DX IC401 BD3426K-E2 (MAIN Board (1/4)) FADER BP22 FADER BP32 SUB-OUT FL-OUT FADER GENERAL PURPOSE (+20~-20dB/2dB STEP) FADER RL-OUT SCF BASE & TREBLE (+20~-20dB/2dB STEP) FR-OUT FADER RR-OUT FADER VOLUME(0~-72dB, -∞dB) LOUDNESS +15dB~-32dB 1dB/STEP -32dB~-46dB 2dB/STEP LOUDNESS -46dB~-78dB 4dB/STEP ON/OFF -∞...
- Page 39 CDX-GT800D/GT805DX IC201 TDA8588AJ/N2/R1 (MAIN Board (2/4)) OUT FL- I2C BUS OUT FL+ OUT RL- PGND3 OUT RL+ INRL INFL SGND PROTECTION DIAGNOSTIC INFR INRR AC GND OUT RR+ PGND2 OUT RR- OUT FR+ STANDBY MUTE OUT FR- CHIP DETECT DIAGNOSTIC...
- Page 40 CDX-GT800D/GT805DX IC620 NJM2377M(TE2) (MAIN Board (4/4)) 30µA VREF U.VLO S.C.P ER.AMP 0.52V IC110 BA8271F-E2 (MAIN Board (4/4)) BUS ON BUS ON SWITCH RESET SWITCH BUS ON CLK-IN BATTERY BATT B-CHK SWITCH VREF DATA I/O DATA IN DATA OUT...
- Page 41 CDX-GT800D/GT805DX • IC PIN DESCRIPTIONS • IC3 MB90486BPFV-G-177E1 (CD SYSTEM CONTROL) (SERVO BOARD (2/2)) Pin No. Pin Name Pin Description CDON_1500MV Servo 1.5 V power supply control signal output 2 to 5 — Not used. (Open) DRVON Motor drive mute signal output...
- Page 42 CDX-GT800D/GT805DX Pin No. Pin Name Pin Description XFLASH&EJECT_OK Front panel open signal input H: eject OPEN_REQ Front panel open/close request signal output Not used in this set. MECON Mechanism deck power supply control signal output CDON Servo power supply control signal output...
- Page 43 CDX-GT800D/GT805DX • IC303 M30622MWP-304GP (SYSTEM CONTROL) (MAIN BOARD (3/4)) Pin No. Pin Name Pin Description SIRCS Remote control data signal input FSW-IN FL DC-DC converter frequency count input UNI_SO Control bus serial data output UNI_SI Control bus serial data input...
- Page 44 CDX-GT800D/GT805DX Pin No. Pin Name Pin Description Z_DET Zero detection mute signal input ILL-IN Illumination check signal input ACC_IN Accessory check signal input TEL_ATT Telephone mute signal input TEST_IN Test mode signal input RC_IN1 Remote control signal input 1 SYSRESET...
- Page 45 CDX-GT800D/GT805DX • IC901 M30876MJB-053GP (FL DISPLAY CONTOROL) (DISPLAY BOARD) Pin No. Pin Name Pin Description SYS_CE Chip enable signal input — Not used (Open) FL_DAT3 FL serial data-3 output — Not used (Open) FL_CLK_IN FL serial transfer clock input (Connected to 35,100 pin)
-
Page 46: Exploded Views
CDX-GT800D/GT805DX SECTION 5 EXPLODED VIEWS NOTE: • The mechanical parts with no reference • Color Indication of Appearance Parts The components identified by mark 0 or dotted line with mark number in the exploded views are not supplied. Example : 0 are critical for safety. -
Page 47: Main Board Section
CDX-GT800D/GT805DX 5-2. MAIN BOARD SECTION not supplied TUX501 not supplied not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-869-079-11 FLEXIBLE BOARD X-2025-442-2 MOVE (F) ASSY, FOLLOW 1-790-355-54 CORD (WITH CONNECTOR) (RCA) 3-376-464-11 SCREW (+PTT 2.6X6), GROUND POINT... -
Page 48: Front Panel Section
CDX-GT800D/GT805DX 5-3. FRONT PANEL SECTION not supplied not supplied FL900 not supplied not supplied not supplied not supplied not supplied not supplied not supplied not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark... -
Page 49: Cd Mechanism Section (1)
CDX-GT800D/GT805DX 5-4. CD MECHANISM SECTION (1) (MG-611WD-186//Q) not supplied (SENSOR board) not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-3372-444-B CHASSIS (T) SUB ASSY 3-259-033-01 DAMPER (S) 3-253-729-11 SPRING (LR), TENSION COIL... -
Page 50: Cd Mechanism Section (2)
CDX-GT800D/GT805DX 5-5. CD MECHANISM SECTION (2) (MG-611WD-186//Q) (including M901) M902 not supplied not supplied not supplied not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-1075-644-A CHASSIS (OP) COMPLETE ASSY A-3372-446-A LEVER (SL) SUB ASSY 3-316-938-91 SCREW (B1.4X5), TAPPING... -
Page 51: Cd Mechanism Section (3)
CDX-GT800D/GT805DX 5-6. CD MECHANISM SECTION (3) (MG-611WD-186//Q) M903 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-348-993-01 WASHER 2-186-696-02 BRACKET (LEM-N) 2-186-699-01 GEAR (RA1) 3-345-648-91 SCREW (M1.4), TOOTHED LOCK A-1075-641-B ARM ASSY, ROLLER A-1083-636-A GEAR (LE) ASSY... -
Page 52: Cd Mechanism Section (4)
CDX-GT800D/GT805DX 5-7. CD MECHANISM SECTION (4) (MG-611WD-186//Q) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 2-186-700-01 GEAR (CHK1) 2-630-962-01 WASHER (SLIT) 3-344-223-01 WASHER * 306 2-590-545-01 GEAR (LE2-M) 3-259-470-12 GEAR (LE1) A-1075-640-B CHASSIS (M) BLOCK ASSY... -
Page 53: Electrical Parts List
CDX-GT800D/GT805DX SECTION 6 BASE PANEL DISPLAY ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in • Items marked “*” are not stocked since The components identified by mark 0 or dotted line with mark. the parts list may be different from the they are seldom required for routine service. - Page 54 CDX-GT800D/GT805DX DISPLAY MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark LED906 6-500-476-01 LED SML310BA1TT86 (OFF) R955 1-216-833-11 METAL CHIP 1/10W LED907 6-500-476-01 LED SML310BA1TT86 (MENU) R956 1-216-809-11 METAL CHIP 1/10W LED908 6-500-476-01 LED SML310BA1TT86 (Z/ANGLE)
- Page 55 CDX-GT800D/GT805DX MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C205 1-115-340-11 CERAMIC CHIP 0.22uF C341 1-162-970-11 CERAMIC CHIP 0.01uF C206 1-165-908-11 CERAMIC CHIP C342 1-162-970-11 CERAMIC CHIP 0.01uF C207 1-165-908-11 CERAMIC CHIP C400 1-124-717-85 ELECT...
- Page 56 CDX-GT800D/GT805DX MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C512 1-107-725-11 CERAMIC CHIP 0.1uF C820 1-216-864-11 SHORT CHIP C513 1-126-933-11 ELECT 100uF C822 1-162-964-11 CERAMIC CHIP 0.001uF C514 1-107-826-11 CERAMIC CHIP 0.1uF C850 1-107-826-11 CERAMIC CHIP 0.1uF...
- Page 57 CDX-GT800D/GT805DX MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark D114 8-719-053-18 DIODE 1SR154-400TE-25 FB551 1-216-001-00 RES-CHIP 1/10W D115 8-719-053-18 DIODE 1SR154-400TE-25 (GT800D) D116 8-719-053-18 DIODE 1SR154-400TE-25 FB552 1-216-001-00 RES-CHIP 1/10W D117 8-719-053-18 DIODE 1SR154-400TE-25 (GT800D)
- Page 58 CDX-GT800D/GT805DX MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < JACK > R117 1-216-821-11 METAL CHIP 1/10W R118 1-216-821-11 METAL CHIP 1/10W PJ401 1-774-700-11 JACK, PIN 6P (AUDIO OUT FRONT/REAR, R119 1-216-829-11 METAL CHIP 4.7K...
- Page 59 CDX-GT800D/GT805DX MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R341 1-216-821-11 METAL CHIP 1/10W R471 1-216-819-11 METAL CHIP 1/10W R342 1-216-845-11 METAL CHIP 100K 1/10W R472 1-216-819-11 METAL CHIP 1/10W R343 1-216-809-11 METAL CHIP 1/10W...
- Page 60 CDX-GT800D/GT805DX MAIN SENSOR SERVO Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R660 1-218-847-11 METAL CHIP 0.5% 1/10W X302 1-781-679-11 VIBRATOR, CRYSTAL (6MHz) R661 1-216-845-11 METAL CHIP 100K 1/10W X551 1-813-173-11 VIBRATOR, CRYSTAL (8.664MHz) (GT800D) R662 1-218-843-11 METAL CHIP 0.5%...
- Page 61 CDX-GT800D/GT805DX SERVO Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-162-964-11 CERAMIC CHIP 0.001uF 1-218-989-11 RES-CHIP 1/16W 1-125-777-11 CERAMIC CHIP 0.1uF 1-218-989-11 RES-CHIP 1/16W 1-100-567-81 CERAMIC CHIP 0.01uF 1-218-947-11 RES-CHIP 1/16W 1-100-567-81 CERAMIC CHIP 0.01uF 1-218-990-81 SHORT CHIP 1-100-567-81 CERAMIC CHIP 0.01uF...
- Page 62 CDX-GT800D/GT805DX SERVO SUB PANEL Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R145 1-218-990-81 SHORT CHIP PARTS FOR INSTALLATION AND CONNECTIONS *************************************** < SWITCH > X-3382-647-1 FRAME ASSY, FITTING 1-529-565-61 SWITCH, PUSH (1 KEY) (DOWN) 1-776-207-72 CORD (WITH CONNECTOR) (POWER) 3-246-471-01 KEY (FRAME) <...
- Page 63 CDX-GT800D/GT805DX MEMO...
-
Page 64: Revision History
CDX-GT800D/GT805DX REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2005.12...