MFB Tanzbar User Manual page 6

Play Mode – Playing the Tanzbär
Manual Trigger Mode
Audition of sounds
Right after powering up, Tanzbär's MANUAL TRIGGER MODE is active. The LED
"Rec/ManTrig" lights constantly green. Now you can trigger the sounds with the
Step/Instrument buttons. You can also tweak all sounds with their dedicated parameter
knobs.
Play Mode
Pattern Memory
Tanzbär's pattern memory uses 3 sets (A, B and C) with 3 banks each. Each bank contains
16 patterns which makes 144 patterns in total.
Set A is packed with factory patterns. Banks 1 and 2 contain great beats made by the
Berlin based techno wizzard Yapacc, Bank 3 sports the original patterns of the "MFB Kult"
drummachine. Sets B and C are ready for your own great creations. If desired, the content
of Set A can be overwritten.
Set (3x) A
Bank (9x) 1 2 3
Pattern (144x) 1-16 1-16 1-16 1-16 1-16 1-16
by Yappacc MFB Kult
Factory-Patterns
Pattern Selection
To select patterns, PLAY MODE or MANUAL TRIGGER MODE has to be active. The LED
Rec/ManTrig should be OFF or constantly GREEN (please refer to fig. on page 9).
• Hold Shift + press Set A button. Set A is selected.
• Hold Shift + press Bank button. The Bank button toggles between Bank 1 (green),
2 (red) and 3 (orange).
• Press Step button. If you press Step 1, pattern 1 is loaded etc. Red Step LEDs
show used patterns. The currently loaded pattern lights orange.
When the sequencer is running, a pattern change is allways performed at the next "1" of
the following bar.
Pattern Playback
Start/stop the sequencer
• Press Play. The sequencer starts. Press Play again and the sequencer stopps.
This also works when Tanzbär is synced to MIDI-clock.
MFB Tanzbär
Shift
B C
hold
Shift
1 2 3
1 2 3
hold
Step-Button 1-16
1-16 1-16 1-16
10
MFB Tanzbär
Adjust Tempo
• Hold Shift + move the Data knob.
To avoid tempo jumps, the tempo change is performed right at the moment, when the knob
position matches the previous tempo setting.
As soon as you release the Shift button, the new tempo is saved. There is no tempo read-
out on Tanzbär. The values range of the knob covers approx. 60 BPM to 180 BPM.
In Play Mode (Rec/ManTrig LED OFF) you cannot only playback existing patterns, you can
also tweak them "live" in several ways. In this mode, Tanzbär's buttons open up certain
appropriate functions. The following figure shows the functions of all relevant buttons. In
the following text, these functions will be explained in detail.
select Mode select Mode
Set A/B/C
+
press repetedly
Function-Buttons Function-Buttons
in Play-Mode: in Record-Mode in Play-Mode: in Record-Mode
Bank (Per-Step-Programming): (Per-Step-Programming):
+
- Accent - Accent
- Accent (for Rolls) - Accent (for Rolls)
press repetedly
- Bend-Function - Bend-Function
- Roll-Function - Roll-Function
- add. Sound-Parameter - add. Sound-Parameter
- Flam-Function - Flam-Function
press
chain Patterns chain Patterns
(in Play-Mode) (in Play-Mode)
Pattern A/B toggel / copy Pattern A/B toggel / copy
select Pattern
(in Play-Mode)
1. Mute Function
In PLAY MODE, all instruments can be muted via their corresponding Step/Instrument
button (e.g. Step 3 = BD 1, Step 7 = Cymbal etc.). The LED of a muted instrument lights up
red. If the patterns is stored, active mutes will also be stored. The store function is covered
on page 23.
2. Accent Function
Sets accents on three different levels. The Acc/Bnd button toggles between the three
levels (LED off/green/red). In Play Mode, the Accent level affects the Roll function (see
below).
Please note: After powering up, Tanzbär has to be set to PLAY MODE in
order to playback patterns (press Rec/ManTrig, leD has to be OFF). Then
select a pattern (press Pattern, Step button, please see above).
Sound-Parameter
Step-Buttons Step-Buttons
select Pattern in Play-Mode: in Play-Mode:
(in Play-Mode) - Pattern-Selection - Pattern-Selection
- Instrument-Selection (Man-Trg-Mode) - Instrument-Selection (Man-Trg-Mode)
- Function-Selection (with Shift) - Function-Selection (with Shift)
- Parameter-Values - Parameter-Values
11
Play Mode – Playing the Tanzbär
Sound-Parameter
Tempo / Tempo
(Shift)
Sound-Parameter Sound-Param
Start/Stop
Shuffle-Fctn Shuffle-Fct
select / select /
confirm confirm
2.Fctn-Level 2.Fctn-Level
in Record-Mode: in Record-Mode:
- Track-Selection - Track-Selection
- Step-Selection - Step-Selection
- Function-Selection (with Shift) - Function-Selection (with Shift)
- Parameter-Values - Parameter-Values
(Shift)
Start/Stop