Infinity 890 BF Owner's Manual
  1. Manuals
  2. Brands
  3. Infinity Manuals
  4. Indoor Fireplace
  5. 890 BF
  6. Owner's manual

Infinity 890 BF Owner's Manual

Room sealed inset live fuel effect gas fire
Hide thumbs
Table of Contents

Advertisement

Quick Links

ROOM SEALED INSET LIVE FUEL EFFECT GAS FIRE
OWNER'S
MANUAL
Please read these instructions carefully before you start
using the appliance
Keep this booklet handy for future reference
This appliance is
For use in GREAT BRITAIN or
IRELAND only
TELFORD
SHROPSHIRE
ENGLAND

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 890 BF and is the answer not in the manual?

Questions and answers

Related Manuals for Infinity 890 BF

Summary of Contents for Infinity 890 BF

  • Page 1 ROOM SEALED INSET LIVE FUEL EFFECT GAS FIRE OWNER'S MANUAL Please read these instructions carefully before you start using the appliance Keep this booklet handy for future reference This appliance is For use in GREAT BRITAIN or IRELAND only TELFORD SHROPSHIRE ENGLAND...

  • Page 2: Table Of Contents

    INFINITY 890 BF Instructions CONTENTS PAGE User’s Instructions SECTION ONE Important Information Consumer Protection Health and Safety Notice SECTION TWO Introduction SECTION THREE Operation Lighting the Fire Turning Off the Fire Replacing Appliance Batteries SECTION FOUR Cleaning and Fuel Bed Laying...

  • Page 3: Section One Important Information

     As the INFINITY 890 BF is a room sealed appliance (i.e. air for the combustion process is taken from outside the room) no purpose built ventilation is required. ...

  • Page 4: Users Instructions

    Regulations and the current ETCI rules for electrical installation, if appropriate.  Although the INFINITY 890 BF is fitted with a glass front which acts as a dress guard it is strongly recommended that a fireguard should be used for the protection of children, the elderly or infirm.

  • Page 5: Section Two Introduction

    Introduction  The INFINITY 890 BF is an inset room sealed decorative fuel-effect gas appliance designed for use in locations that do not have a conventional chimney. The appliance must be installed against an outside wall because the air to support combustion is taken from the outside and the products of combustion are expelled to the outside.

  • Page 6: Section Three Operation

    INFINITY 890 BF Users Instructions SECTION THREE Operation Cont. e. The appliance can be switched off with out using the hand set by removing the appliance batteries located behind the fascia. When the batteries are removed there will be a delay (up 3minutes) after which, double bleeps may be heard and shortly after the appliance will extinguish.

  • Page 7: Cleaning: Black Painted Surfaces

    INFINITY 890 BF Users Instructions SECTION THREE Operation Cont. To Deactivate the sleep mode: When the fire is next operated, the sleep mode will automatically appear unless it is re-set to zero. This can be done by pressing the key and using the button to decrease the time set by 15 minute intervals until back to zero.

  • Page 8: Cleaning: Glass Panel

    INFINITY 890 BF Users Instructions SECTION FOUR Cleaning & Laying the fuel bed CLEANING: GLASS PANEL From time to time it may be necessary to clean the glass panel. We recommend you use a Ceramic Hob Cleaner (brands such as HOB BRITE and VITRO CLEN have been found to be acceptable) these are available from most leading Supermarkets.
  • Page 9 INFINITY 890 BF Users Instructions SECTION FOUR Cleaning & Laying the fuel bed Continued Log Fuel Bed Layout.  The Burner End Plates should already position at ends of burner carrier and held in place with self tapping screws with chamfered ends towards the front.
  • Page 10 INFINITY 890 BF Users Instructions SECTION FOUR Cleaning & Laying the fuel bed Continued Log Fuel Bed Layout  Place the first three rear straight log shapes on top of the Air Bridge as far back rear possible as shown in the picture and space them evenly.
  • Page 11 INFINITY 890 BF Users Instructions SECTION FOUR Cleaning & Laying the fuel bed Continued Log Fuel Bed Layout  Position the Smallest Log shape as shown in picture.  Place the next Two Middle shapes as shown, resting on the rear...
  • Page 12 INFINITY 890 BF Users Instructions SECTION FOUR Cleaning & Laying the fuel bed Continued Log Fuel Bed Layout  Place the last Two large shapes and last small shape as shown, making sure the last right hand shape does not cover the pilot flame.

  • Page 13: Section Five Appliance Data

    INFINITY 890 BF Installation Instructions SECTION FIVE Appliance Data Fire Box dimensions: Height 456mm Width 970mm Forward Projection: 10mm Overall Trim dimensions………………………………….Height 462mm Width 1054mm Trim Forward dimensions………………………………………………..23mm Weight: 35kg Flue Length………………………………………...100mm (minimum) to 1000mm (maximum) Standard length supplied with fire 535mm(267.5mm after cutting).

  • Page 14: Section Six Regulations And Warnings

    INFINITY 890 BF Installation Instructions SECTION SIX Regulations and Warnings  This appliance must only be installed in Great Britain or Ireland.  The appliance is available in natural gas only.  This appliance must be installed on a suitable outside wall.

  • Page 15: Section Seven Siting The Appliance

    INFINITY 890 BF Installation Instructions SECTION SEVEN Siting the Appliance (When installing in a timber framed dwelling reference must be made to the specific installation requirements stated in Section 9 Installing the Appliance in Timber Framed Dwelling). GENERAL REQUIREMENTS ...

  • Page 16: Section Eight

    INFINITY 890 BF Installation Instructions SECTION SEVEN Siting the Appliance Continued  The back panel of the surround must have ALL DIMENSIONS IN mm a cutout within the maximum and minimum dimensions as shown.  900 MIN Ensure that gas supply is suitably sited.

  • Page 17: Installing The Appliance Into A Cavity Wall

    INFINITY 890 BF Installation Instructions SECTION NINE To Install the Appliance INSTALLING THE APPLIANCE INTO CAVITY WALL. ( When installing in a timber framed dwelling reference must be made to the specific installation requirements stated later in this Section ‘Installing The Appliance In Timber Framed Dwelling’).
  • Page 18 INFINITY 890 BF Installation Instructions SECTION NINE To Install the Appliance Continued  Using 125mm (5”) core drill cut two holes following the pilot holes. Drill from the outside through to the cavity to give a good finish on the outside.

  • Page 19: Installing The Appliance Into A Dummy Breast

    INFINITY 890 BF Installation Instructions SECTION NINE To Install the Appliance Continued INSTALLING THE APPLIANCE INTO A DUMMY CHIMNEY BREAST. ( When installing in a timber framed dwelling reference must be made to the specific installation requirements stated later in this Section ‘Installing The Appliance In Timber Framed Dwelling’).
  • Page 20 INFINITY 890 BF Installation Instructions SECTION NINE To Install the Appliance Continued  Drill the four fixing holes through the holes in the flange of the appliance and fix back using plugs and screws.  If the flue outlet is fitted below 2m from the floor or a balcony then a flue terminal guard must be fitted.

  • Page 21: Connecting The Gas Supply

    INFINITY 890 BF Installation Instructions SECTION TEN CONNECTING THE GAS SUPPLY TURN OFF ANY GAS APPLIANCES THAT ARE FED BY THE METER AND ISOLATE THE GAS SUPPLY BY TURNING OFF AT THE METER.  Connections may be made in 8mm-dia pipe by a concealed connection from the left hand rear of the appliance with the grommet provided.

  • Page 22: Section Eleven Check Operation Of Fire

    INFINITY 890 BF Installation Instructions SECTION ELEVEN Check Operation of Fire CHECK BURNER PRESSURE AND GENERAL OPERATION  Remove the screw from the pressure test point on the burner inlet elbow and fit a pressure test gauge.  Turn on the gas to the appliance and operate as described in section three. Check that the inlet pressure 20mbar +/- 1 mbar for natural gas.

  • Page 23: Maintenance Instructions

    INFINITY 890 BF Maintenance Instructions SECTION THIRTEEN Maintenance Instructions General  Servicing should be carried out annually by a competent person such as a GAS SAFE-registered person in accordance with the relevant regulations, to ensure the safe and correct operation of the appliance.

  • Page 24: Replacement Of The Thermocouple

    Turn on the gas supply, check for gas soundness, operation and re-commission appliance. When ordering parts quote 'INFINITY 890 BF' and the serial number of the fire, which can be found on the data badge on bottom left hand side of fire. (Refer to cleaning instructions for trim removal.)
  • Page 25 Infinity Fires INFINITY 890 BF THIS IS YOUR EXTENDED FIVE YEAR PARTS WARRANTY PLEASE READ IT CAREFULLY AND ENSURE YOUR INSTALLER HAS FILLED IN THE FIRST PORTION, KEEP IT IN A SAFE PLACE SO THAT IT IS AVAILABLE GAS SAFE WHEN YOUR ENGINEER CARRIES OUT THE ANNUAL SERVICE.
  • Page 26 For future reference we suggest you record the following details here, and keep the receipt as proof of purchase. This information may be asked for when you contact the helpdesk. Model: INFINITY 890 BF Serial No. This information can be found on the label attached to the packaging and on the data badge, which is located on the base of the appliance behind the control cover.
  • Page 27 The following information must be complete and supported by receipts as part of the conditions of the extended five year parts warranty and the appliance must be registered by completing and returning the registration document (last page of this booklet) to Infinity Fires. Date of First annual service: Engineer Name Gas Safe Registration No.
  • Page 28 LT 6541 (Iss 4 07/14)
  • Page 29 Post Code TELEPHONE No. PRODUCT DETAILS Model: INFINITY 890 BF Serial No. Date of Purchase This information can be found on the label attached to the packaging and on the data badge, which is located on the base of the appliance behind the control cover.
  • Page 30 LT 6541 (Iss 4 07/14)
  • Page 31 LT 6541 (Iss 4 07/14)
  • Page 32 Product Serial A-0390 Label Prefix Data Badge Burner Tray / Box Assembly Air Test Completed Battery Insulation Blanket Warning Label (1409) Grommet (1406) Glass Sub-Assembly Silicone Sealing Strip (4818) Linings (Side, rear and top) “AAA” Batteries ( 3 ) Remote Control Hand Set “C”...

Table of Contents