Regency Ceiling Fans Marquis Series Owner's Manual
  1. Manuals
  2. Brands
  3. Regency Ceiling Fans Manuals
  4. Fan
  5. Marquis Series
  6. Owner's manual

Regency Ceiling Fans Marquis Series Owner's Manual

Ceiling fans
Hide thumbs

Advertisement

Table of Contents

Style that revolves around you.
• C
F
O
M
•
EILING
AN
WNER'S
ANUAL
• M
/C
S
•
ARQUIS
OUNTESS
ERIES
REVISED NOVEMBER 2007
WARNING: Read and follow these instructions carefully and be mindful of all warnings shown throughout.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Marquis Series and is the answer not in the manual?

Questions and answers

Related Manuals for Regency Ceiling Fans Marquis Series

Summary of Contents for Regency Ceiling Fans Marquis Series

  • Page 1 Style that revolves around you. • C • EILING WNER'S ANUAL • M • ARQUIS OUNTESS ERIES REVISED NOVEMBER 2007 WARNING: Read and follow these instructions carefully and be mindful of all warnings shown throughout.
  • Page 2 & O ENERAL NSTALLATION PERATION NSTRUCTIONS MPORTANT AFEGUARDS 1. To ensure the success of the installation, be sure to read the instructions and review the diagrams thoroughly before beginning. 2. To avoid possible electric shock, be sure electricity is turned off at the main power box before wiring. All electrical connections must be made in accordance with local codes, ordinances and/or the National Electric Code.

  • Page 3: Important Safety Precautions

    MPORTANT AFETY RECAUTIONS Thank you for choosing a Regency Ceiling Fan. You have chosen the best! Your new ceiling fan has been designed to provide many years of service and enjoyment. Warnings: • Disconnect power by removing fuse or turning off circuit breaker before installing the fan and/or optional lighting.

  • Page 4: Unpacking Your Fan

    NPACKING 1. Unpack your fan and check the contents. Do not discard the carton. If warranty replacement or repair is ever necessary, the fan should be returned in original packing. Remove all parts and hardware. Do not lay motor housing on its side, or the decorative housing may shift, be bent or damaged. 2.

  • Page 5: Installing The Mounting Bracket

    REPARATION Parts identification on assembled fan Canopy Collar Downrod Cover Blade Motor Housing Detachable Blade Switch Housing REPARATION Verify you have all parts before beginning the installation. Check foam insert closely for missing parts. Remove motor from packing. To avoid damage to finish, assemble motor on soft padded surface or use the original foam inset in motor box.
  • Page 6 NSTALLING NSTALLATION This fan has two installation options: #1 HUGGER MOUNTING The HUGGER method is preferred if maximum headroom is required. The ceiling must be horizontal, not sloped. Blades will be approximately 8˝ from the ceiling. Air flow will be reduced when the fan is installed using the HUGGER method.
  • Page 7 NSTALLING THE UGGER TYLE #1: H NSTALLATION PTION UGGER TYLE OUNTING NOTE: The S hook is to be used for hugger style mounting. 1. Remove the plastic trim ring from the canopy to expose the 6 mounting holes. The downrod, ball and cotter pin will not be used for this mounting (Fig.
  • Page 8 – D NSTALLING THE OWNROD STYLE #2: D NSTALLATION PTION OWNROD STYLE MOUNTING 1. Carefully support fan body (motor) in its styrofoam packing with the mounting collar (where the wires come out) facing upward. 2. Remove ball from downrod by loosening set screw in the side of the ball. Slide ball down and remove ball pin; remove ball.
  • Page 9 – D NSTALLING THE OWNROD STYLE #2: D NSTALLATION PTION OWNROD STYLE MOUNTING CONT 1. Lift ball/downrod/fan into hanger bracket opening. NOTE: The tab opposite hanger bracket opening should fit in slot on ball. 2. Make wire connections, (refer to section titled “Electrical Connections”). 3.
  • Page 10 LECTRICAL ONNECTIONS Be sure electricity is turned off at the main power box before wiring LECTRICAL ONNECTIONS 1. Four wires are connected to the fan. Black – this is the “hot” power to run fan. White – this is the “common” power to run fan and light. Blue –...

  • Page 11: Blade Attachment

    LADE TTACHMENT LADE TTACHMENT 1. Place fiber washer on screw. Insert this assembly through the blade and start the screw into the blade arm. Repeat this procedure without tightening the screw until all 3 screws have been started into the blade arm (Fig. 1). NOTE: Fans that have painted finishes are packed with gaskets that can be used between the blade arm and blade to help prevent a clicking noise that may develop if blade screws loosen over time.
  • Page 12 NSTALLATION OF EMOVABLE WITCH OUSING NOTE: Be sure the power is off before installing. 1. Loosen the 3 side screws on switch housing hub halfway. 2. If installing light kit, carefully remove light kit plug in bottom of switch housing. Attach light kit to switch housing per instructions supplied with light kit.

  • Page 13: Operation

    Interchanging adjacent blades may redistribute mass and result in smoother operation. Blade arms can be bent slightly to restore same pitch to all blades if a blade is different than the other blades when viewed edge on. 5/04 Regency Ceiling Fans...

  • Page 14: Care And Cleaning

    HANK YOU FOR PURCHASING A EGENCY EILING Write to us at: Regency Ceiling Fans P.O. Box 730 Fenton, MO 63026 Visit us on the Web at: www.regencyfan.com 2/01 Regency Ceiling Fans...

This manual is also suitable for:

Countess series

Table of Contents

Save PDF