Table of Contents
Advertisement
Quick Links
I
N
S
T
A
I
N
S
T
A
Single Station Thermal Printer
Patersstraat 106-108
2300 Turnhout
Tel:014/42.55.99
Fax: 014/42.32.64
M
M
This printer has been manufactured and branded for ORIENT Technologies
B.V. by Shandong New Beiyang Information Technology Co., Ltd.
Design and specifications are subject to change without notice. Ask your
supplier for technical specifications before purchase and/or use.
Whenever in doubt about safety issues that might arise from using this product,
please contact the supplier immediately for assistance.
L
L
A
T
I
O
L
L
A
T
I
o
d
e
l
:
B
T
P
o
d
e
l
:
B
T
P
N
M
A
O
N
M
A
BTW BE 0415.638.961
Rek: 230-0026460-96
info@vanmechelen.be
www.vanmechelen.be
-
2
0
0
2
N
P
-
2
0
0
2
N
P
N
U
A
L
N
U
A
L
Advertisement
Table of Contents
Related Manuals for Van Mechelen BTP-2002NP
Summary of Contents for Van Mechelen BTP-2002NP
- Page 1 Single Station Thermal Printer BTW BE 0415.638.961 Patersstraat 106-108 Rek: 230-0026460-96 2300 Turnhout Tel:014/42.55.99 info@vanmechelen.be Fax: 014/42.32.64 www.vanmechelen.be This printer has been manufactured and branded for ORIENT Technologies B.V. by Shandong New Beiyang Information Technology Co., Ltd. Design and specifications are subject to change without notice. Ask your supplier for technical specifications before purchase and/or use.
- Page 2 (DNV)ISO9001:2000 The environmental control system of SNBC has been approved of the following certification. (DNV)ISO14001:2004 BTP-2002NP has been approved of the following certification. WEEE directive 2002/96/EC ORIENT Technologies bv is complying with all aspects of the European Union’s WEEE directive 2002/96/EC.
- Page 3 BTP-2002NP Installation manual Contact us In CHINA: Address: No.169 Huoju Rd, Weihai, Shandong, China. 264209 Hot line: +86-631-5673777 Fax: +86-631-5673778 E-mail: sales@newbeiyang.com Website: www.newbeiyang.com (via Contact button) In EUROPE: ORIENT Technologies bv Address: Meerheide 115, 5521 DX Eersel, The Netherlands...
-
Page 4: Table Of Contents
BTP-2002NP Installation manual CONTENT GENERAL SAFETY INFORMATION............. 2 PARTS IDENTIFICATIONS ............3 SETTING UP THE PRINTER ............5 Unpacking ................5 Connecting the Cables............5 2.2.1 Interface Connector .............6 2.2.2 Cash Drawer Connector ............8 Loading the Paper Roll ............8 SWITCH, BUTTON AND LED ............11 Power Switch ............... -
Page 5: General Safety Information
BTP-2002NP Installation manual General Safety Information Before installing and using the printer, please read the following items carefully. Safety Labels Don’t touch the cutter and tear bar of printer. The print head is a thermal element and it is at high temperature during printing or just after operation, therefore please do not touch it and its peripherals for safety reasons. -
Page 6: Parts Identifications
BTP-2002NP Installation manual Parts Identifications 1— Cutter cover 2— Tear bar 3— Printer top cover 4— Power LED Indicating power status (ON/OFF). 5— Error LED indicates basic information about the status of the printer. When the LED is off, the printer is operating normally. - Page 7 BTP-2002NP Installation manual 12－Cutter acting blade 13－Printer platen 14－Cutter fixed blade 15－Paper end sensor For continuous paper, this sensor is used to detect whether the paper roll has run out. 16－Paper-width-adjust module There are 4 long slots at the base of paper...
-
Page 8: Setting Up The Printer
BTP-2002NP Installation manual Setting UP the Printer 2.1 Unpacking Your printer box should include these items. If any items are damaged or missing, please contact your dealer for assistance. 2.2 Connecting the Cables You can connect up the cables required for printing to the printer. They all... -
Page 9: Interface Connector
BTP-2002NP Installation manual 2.2.1 Interface Connector RS-232 serial interface (DB25F) Signal Signal Function name direction — Frame ground Output Transmit data Input Receive data Output Same as DTR signal Input This signal indicates whether the host computer can receive data. -
Page 10: Parallel Interface
BTP-2002NP Installation manual Parallel interface Source Function Source Function NStrobe Signal Ground (nStrobe) Data 0 Signal Ground (Data 1) (Least Significant Bit) Data 1 Signal Ground (Data 2) Data 2 Signal Ground (Data 3) Data 3 Signal Ground (Data 4) -
Page 11: Cash Drawer Connector
BTP-2002NP Installation manual USB interface Pin Number Signal Name Function VBUS DATA- Printer data transmit line minus DATA+ Printer data transmit line plus Ground 2.2.2 Cash Drawer Connector The drawer kick-out drive pulses are generated by command. The host can retrieve the status of the drawer by using the DLE EOT, GS a, or GS r commands. - Page 12 BTP-2002NP Installation manual Caution: Adjust the paper width by adjusting the paper-width-adjust module according to the paper type used. Make sure that the paper roll is cut according to the requirement below before loading: Make sure that the heat sensitive side of paper faces the print head and the rolling direction of paper meets the requirements.
- Page 13 BTP-2002NP Installation manual 5) Tear off the surplus portion of paper by using the tear bar. Caution: While encountering cutter malfunction due to paper jam or unexpected power loss, do not open the top cover of the printer by force since the moving blade of the cutter might blocked the cover.
-
Page 14: Switch, Button And Led
BTP-2002NP Installation manual Switch, Button and LED 3.1 Power Switch The power button (a rocker switch) turns the power on or off. Turn the power on only after connecting the power supply. Note: 3.2 Feed Button FEED button: Pushing this button the printer feeds paper, however the FEED button is blocked during the following conditions: ●... -
Page 15: Self-Test
BTP-2002NP Installation manual the temperature of the print head has increased too much, the printer will decrease its print speed. If the temperature becomes higher than 65℃, the protection circuit of the printer will force the printer to stop printing; at the same time the light and sound signals as described in the table will be given. -
Page 16: Specifications
BTP-2002NP Installation manual ENQ, and DLE DC4 are not executed. (3) Insufficient print data to fill the last line can be printed by pressing the FEED button. Ending hexadecimal dumping Hexadecimal dump mode can be ended by turning off the power, or press the FEED button three times, or reset the printer after printing has finished. -
Page 17: Auto Cutter Specifications
BTP-2002NP Installation manual 6.2 Auto Cutter Specifications Item Parameter Remarks Cutter type Slide cutter (Guillotine type) Cutting time 600ms The time that one cut takes. Cutting interval 30 times/min. (Max.) Thermal paper or paper with the same Paper type Thickness: 0.065 – 0.1mm... -
Page 18: Reliability
BTP-2002NP Installation manual 6.6 Reliability 1) Life times: Thermal head: 100,000,000 pulses, 100 km Auto cutter: 1,000,000 cuts 2) MTBF: 360,000 hours 3) MCBF: 52,000,000 lines 6.7 Black Mark Specifications Printer can work in the mark paper mode, and in accordance with mark to set cutting and the start print location. -
Page 19: Overall Dimension
BTP-2002NP Installation manual 6.8 Overall Dimension FEED Button Configuration Parameter setting (configuring) by Feed button Hold the FEED button pressed while switching the printer on. After the printer has printed the configuration sheet, press and hold the FEED button to configure the printer. The main menu for the key-stroke setting procedure is printed. - Page 20 BTP-2002NP Installation manual Parameter Setting by Feed Button Main Menu Exit Print Self Test Configuration Cutter Test Sensor Test > 1 > 2 > 3 >4 > 5 Setting Configuration of the Printer Configuration Exit Exit with Communi Mech. &...
- Page 21 BTP-2002NP Installation manual Configuration of the Serial Interface Communication Baud Rates Back Parity Data Stop Data Handshak Rx Buffer (default: to last (default: Bits Bit(s) Receive Size 9600 bps) menu none) (default: (default: Error (default: (default: 8 bits) 1 Bit)
- Page 22 BTP-2002NP Installation manual Setting Mechanism and Hardware Mech. & Hardware Back to last Mark Sensor Cutter Buzzer Power Supply menu (default: (default: (default: (default: normal) disabled) enabled) enabled) >1 >2 >3 >4 >5 Choices: Choices: Enabled Choices: Choices: Normal Disabled...
- Page 23 BTP-2002NP Installation manual Print Setting Print Setting Back to Right Code Page Darkness Paper Roll Left Margin (default: PC last menu Margin (default: Width (default: 7 Command 437) (default: 9 normal) (default: 80 (default: >7 disabled) Choices: >1 >4 >5 >2...
- Page 24 BTP-2002NP Installation manual Paper Near-end Sensor setting Paper sensor settings Paper Low Alarm Stop print when paper Back to last menu (default: enabled) >2 (default: disabled) Choices: >3 >1 Enabled Choices: Disabled Enabled Set Default Configuration Set default config Set printer to default config Back to last Menu >2...
Need help?
Do you have a question about the BTP-2002NP and is the answer not in the manual?
Questions and answers