Gas Conversion Kits - Lennox Meris Series MLDVT-30NM Installation Instructions Manual

LENNOX HEARTH PRODUCTS • MERIT

GAS CONVERSION KITS

This conversion kit shall be installed by a qualified service agency in
accordance with the manufacturer's instructions and all applicable codes
and requirements of the authority having jurisdiction. If the information in
these instruction is not followed exactly, a fire, explosion or production of
carbon monoxide may result causing property damage, personal injury
or loss of life. The qualified service agency is responsible for the proper
installation of this kit. The installation is not proper and complete until the
operation of the converted appliance is checked as specified in the manu-
facturer's instructions supplied with the kit. The qualified service agency
performing this installation assumes responsibility for this conversion.
Cette trousse de conversion doit être installée par un technicien agréé,
selon les instructions du fabricant et selon toutes les exigences et tous les
codes pertinents de l'autorité compétente. Assurez-vous de bien suivre
les instructions dans cette notice pour réduire au minimum le risque
d'incendie, d'explosion ou la production de monoxyde de carbone pouvant
causer des dommages matériels, des blessures ou la mort. Le tecnicien
agréé est responsable de l'installation de cette trousse. L'installation n'est
pas adéquate ni complète tant que le bon fonctionnement de l'appareil
converti n'a pas été vérifié selon les instructions du fabricant fournies avec
la trousse. Le fournisseur de service qualifié ayant réalisé l'installation
assume les responsabilités liées à la conversion.
In Canada:
THE CONVERSION SHALL BE CAR-
RIED OUT IN ACCORDANCE WITH THE
REQUIREMENTS OF THE PROVINCIAL
AUTHORITIES HAVING JURISDICTION
AND IN ACCORDANCE WITH THE RE-
QUIREMENTS OF THE CAN/CSA-B149.1
INSTALLATION CODE.
LA CONVERSION DEVRA êTRE EF-
FECTUéE CONFORMéMENT AUX
RECOMMANDATIONS DES AUTORITéS
PROVINCIALES AYANT JURIDICTION
ET CONFORMéMENT AUX EXIGENCES
DU CODE D'INSTALLATION CAN/CSA-
B149.1.
Gas conversion kits are available to adapt your
appliance from the use of one type of gas to
the use of another. These kits contain all the
necessary components needed to complete
the task including labeling that must be af-
fixed to ensure safe operation.
Kit part numbers are listed here, and the
following steps detail the conversion pro-
cedure. Refer to the instructions provided
with the conversion kit when performing any
gas conversion.
SERIES DIRECT-VENT GAS FIREPLACES • MODELS MLDVT-30/35/40/45 • INSTALLATION INSTRUCTIONS
®
WARNING
AVERTISSEMENT
Millivolt SIT Systems
Natural Gas To Propane Gas
Conversion Kits
Models
MLDVT-30
MLDVT-35
MLDVT-40
MLDVT-45
Millivolt SIT Systems
Propane Gas to Natural Gas
Conversion Kits
Models
MLDVT-30
MLDVT-35
MLDVT-40
MLDVT-45
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Models
MLDVT-30
MLDVT-35
MLDVT-40
MLDVT-45
Models
MLDVT-30
MLDVT-35
MLDVT-40
MLDVT-45
INSTALLATION INSTRUCTIONS
Step 1. TURN OFF THE GAS SUPPLY TO THE
APPLIANCE and disconnect power supply at
the circuit breaker. Ensure appliance is cold.
CAUTION: THE GAS SUPPLY SHALL BE
SHUT OFF PRIOR TO DISCONNECTING THE
ELECTRICAL POWER, BEFORE PROCEED-
ING WITH THE CONVERSION.
ATTENTION : AVANT D'EFFECTUER
LA CONVERSION, COUPEZ D'ABORD
L'ALIMENTATION EN GAZ, ENSUITE,
Catalog No.
COUPEZ L'ALIMENTATION éLECTRIQUE.
H7672
Step 2. Remove the front glass door assembly.
H7292
See Figure 49 on Page 31.
H7673
H7546
Step 3. Carefully remove the logs. Take care
not to break the logs.
Step 4. Refer to Figure 55 on Page 38.
Remove the burner assembly with attached
venturi tube.
Catalog No.
H6165
H7293
H7294
85L66
Electronic DEXEN Systems
Natural Gas To Propane Gas
Conversion Kits
Catalog No.
H7668
H7295
H7669
H7544
Electronic DEXEN Systems
Propane Gas To Natural Gas
Conversion Kits
Catalog No.
H6170
H7296
H7297
H7545
37