Chamberlain LiftMaster CSL24V Installation Manual

Vehicular slide gate operator elite series

Hide thumbs Also See for LiftMaster CSL24V:

User manual (8 pages)

Addendum (4 pages)

Quick start manual (2 pages)

Table Of Contents

Table of Contents

Quick Links

Troubleshooting

Need help?

Do you have a question about the LiftMaster CSL24V and is the answer not in the manual?

Questions and answers

Summary of Contents for Chamberlain LiftMaster CSL24V

Page 1 CSL24V™& CSL24VH™ VEHICULAR SLIDE GATE OPERATOR I N S T A L L A T I O N M A N U A L Your model may look different than the model illustrated in this manual. THIS PRODUCT IS TO BE...
Page 3: Table Of Contents
LiftMaster Internet Gateway ........
Page 4: Ul325 Model Classifications
SAFETY UL325 MODEL CLASSIFICATIONS UL325 MODEL CLASSIFICATIONS CLASS I – RESIDENTIAL VEHICULAR GATE OPERATOR A vehicular gate operator (or system) intended for use in a home of one-to four single family dwellings, or a garage or parking area associated therewith. CLASS II –...
Page 5: Safety Installation Information
SAFETY SAFETY INSTALLATION INFORMATION SAFETY INSTALLATION INFORMATION 1. Vehicular gate systems provide convenience and security. Gate systems are 8. Controls intended for user activation must be located at least 6 feet (1.8 m) comprised of many component parts. The gate operator is only one away from any moving part of the gate and where the user is prevented component.
Page 6: Gate Construction Information
SAFETY GATE CONSTRUCTION INFORMATION GATE CONSTRUCTION INFORMATION Vehicular gates should be installed in accordance with ASTM F2200: Standard Specification for Automated Vehicular Gate Construction. For a copy, contact ASTM directly at 610-832-9585 or www.astm.org. GENERAL REQUIREMENTS 3.1.3 A gap, measured in the horizontal plane parallel to the roadway, between a fixed stationary object nearest the roadway, (such as a gate support post) Gates shall be constructed in accordance with the provisions given for the and the gate frame when the gate is in either the fully open position or the...
Page 7: Required Entrapment Protection Devices
SAFETY REQUIRED ENTRAPMENT PROTECTION DEVICES REQUIRED ENTRAPMENT PROTECTION DEVICES To prevent SERIOUS INJURY or DEATH from a moving gate: • Entrapment protection devices MUST be installed to protect anyone who may • Locate entrapment protection devices to protect between moving gate and come near a moving gate.
Page 8: Important Safety Information
SAFETY IMPORTANT SAFETY INFORMATION IMPORTANT SAFETY INFORMATION INSTALLATION To prevent SERIOUS INJURY or DEATH from a moving gate: • Pinch points must be guarded at all times. Install enclosed-style gate tracks and • Entrapment protection devices MUST be installed to protect anyone who may roller guards.
Page 9 • To reduce the risk of FIRE or INJURY to persons use ONLY LiftMaster part • ALWAYS keep people and objects away from the gate. NO ONE SHOULD CROSS 29-NP712 for replacement batteries.
Page 10: Introduction
Maximum Gate Travel Distance: Input Rating: 1 foot/second Maximum Gate Speed: • CSL24V: 10 Amps at 120 Vac or 2 Amps at 240 Vac Continuous duty Daily Cycle Rate AC power: • CSL24VH: 12 Amps at 120 Vac Ambient Temperature: Input Rating Excluding Accessory Outlets: •...
Page 11: Features
INTRODUCTION FEATURES FEATURES OPERATOR FEATURES • Advanced "Centerpiece" Control Board • Manual - Secure power failure selection • EMI AC Power Surge Protection and Filter Board • SAMS compatible - Main AC voltage input selection: 120 Vac (factory setting) or •...
Page 12: Preparation
PREPARATION SITE PREPARATION Check the national and local building codes BEFORE installation. GATE Gate must be constructed and installed according to ASTM F2200 standards (refer to page 4). Gate must fit specifications of operator (refer to specifications). SAFETY CATCH ROLLERS DO NOT use a gate catch post.
Page 13: Preparation
SITE PREPARATION CONDUIT & CONCRETE PAD EARTH GROUND ROD Conduit must be UL approved for low and high voltage. Consider the operator Proper grounding gives an electrical placement BEFORE installing the pad or post. charge, such as from an electrical static discharge or a near lightning strike, a path from which to dissipate its energy safely into the earth.
Page 14: Installation
INSTALLATION DETERMINE LOCATION FOR CONCRETE PAD AND OPERATOR + CONCRETE PAD & OPERATOR ATTACHMENT DETERMINE LOCATION FOR CONCRETE PAD AND OPERATOR STANDARD INSTALLATION The gate operator should be installed near the front roller of the gate or near the back of the gate (in the OPEN position). The space between the gate and the output sprocket must be a minimum of 4 inches.
Page 15: Standard Installation Only
INSTALLATION STANDARD INSTALLATION ONLY + REAR INSTALLATION ONLY STANDARD INSTALLATION ONLY DO NOT run the operator until instructed. Manually open the gate and line up the front bracket so the chain will be level with the idler pulley and parallel to the ground. Weld the front bracket in this position.
Page 16: Wiring
WIRING WIRE THE ENTRAPMENT PROTECTION DEVICES + EARTH GROUND ROD WIRE THE ENTRAPMENT PROTECTION DEVICES Entrapment protection devices are required. Refer to page 5 for more information regarding application. To prevent SERIOUS INJURY or DEATH from a moving gate: • Entrapment protection devices MUST be installed to protect anyone who may •...
Page 17: Power Wiring
WIRING POWER WIRING POWER WIRING This operator can be wired for either 120 Vac or 240 Vac or a solar NUMBER OF CYCLES PER DAY panel (not provided). Follow the directions according to your application. Slide Gate Installation (16 ft. 1000 lb. gate) For dual gate applications, power will have to be connected to each operator.
Page 18: Power Wiring
For solar applications DO NOT use the expansion board and the wireless dual gate feature. These features will substantially decrease the cycle 20W SOLAR PANEL rate and standby time of the operator. We recommend LiftMaster low power ✔ NOTE: 20W would be two 10W draw accessories to minimize power draw, refer to accessory page.
Page 19: Connect Batteries
Connect the black wire from the J15 plug to the negative (-) terminal of the battery. Model CSL24V (without heater) Plug the J15 plug back into the control board. This will power up the control set battery tray across the chassis.
Page 20 WIRING CONNECT BATTERIES CONNECT BATTERIES 33AH BATTERIES The batteries are charged in the circuit by the integrated transformer. The batteries (without heater) are for battery backup or solar installation. The 33AH application requires the 33AH wire harness (Model K94-36596). NOTE: If 33AH batteries (2) are used, the battery tray underneath the heater will need to be removed to allow more space in the enclosure (if applicable).
Page 21: Dual Gates Only
WIRING DUAL GATES ONLY DUAL GATES ONLY There are two options for dual gate communication: wired or wireless. Follow the directions according to your application. Do not use wired and wireless communication simultaneously. Wired dual gate applications will have a longer battery standby time than wireless applications. WIRELESS DUAL GATES TO ACTIVATE THE WIRELESS FEATURE: Choose an operator to be the network primary operator.
Page 22 WIRING DUAL GATES ONLY DUAL GATES ONLY WIRED DUAL GATES Before digging, contact local underground utility locating companies. Use PVC conduit to prevent damage to cables. Disconnect ALL power to the operator and unplug the J15 plug from DUAL GATE WIRE TYPE (SHIELDED TWISTED PAIR CABLE) the control board.
Page 23: Adjustment
ADJUSTMENT LIMIT AND FORCE ADJUSTMENT LIMIT AND FORCE ADJUSTMENT To reduce the risk of SEVERE INJURY or DEATH: • Without a properly installed safety reversal system, persons (particularly small • NEVER use force adjustments to compensate for a binding or sticking gate. children) could be SERIOUSLY INJURED or KILLED by a moving gate.
Page 24: Obstruction Test
ADJUSTMENT LIMIT AND FORCE ADJUSTMENT + OBSTRUCTION TEST FINE TUNE THE FORCE The FORCE DIAL on the control board is used for fine tuning the force in cases where wind or environmental changes may affect the gate travel. Based on the length and weight of the gate it may be necessary to make additional force adjustments.
Page 25: Programming
PROGRAMMING REMOTE CONTROLS + ERASE ALL CODES REMOTE CONTROLS (NOT PROVIDED) A total of 50 Security✚ 2.0™ remote controls and 2 keyless entries (1 PIN for each keyless entry) can be programmed to the operator. NOTE: When the memory is full the operator will exit programming mode and the remote control/keyless entry will not be programmed.
Page 26: Finish Installation
FINISH INSTALLATION INSTALL THE COVER INSTALL THE COVER The operator cover consists of two pieces: a rear cover and a front cover. The front cover can easily be removed to access the electrical box. To access the reset switch slide the access door up.
Page 27: Operation
OPERATION RESET SWITCH + REMOTE CONTROL + HEATER (IF APPLICABLE) RESET SWITCH The reset switch is located on the front of the operator and serves several functions. NORMAL OPERATION Toggling the reset switch will stop a moving gate during a normal open/close cycle, like a stop button.
Page 28: Additional Features
Program remote controls 1 to 50 Program remote controls 51 to to the primary operator. 100 to the secondary operator Bi-Part Delay Bi-Part Delay: ON Bi-Part Delay: OFF LiftMaster Internet Program to primary operator. Switch Tandem Mode: OFF Tandem Mode: OFF Gateway Synchronized Close: ON Synchronized Close: ON Garage Door Monitor Program to primary operator.
Page 29: Accessory Features On Control Board
ADDITIONAL FEATURES ACCESSORY FEATURES ON CONTROL BOARD ACCESSORY FEATURES ON CONTROL BOARD Open Input (& common) Open command - opens a closed gate. Hard open (maintained switch overrides external safeties and resets alarm condition) (3-Button Control Station, 4 terminals If maintained, pauses Timer-to-Close at OPEN limit. total) Opens a closing gate and holds open an open gate (within line-of-sight).
Page 30: Expansion Board Overview
ADDITIONAL FEATURES EXPANSION BOARD OVERVIEW EXPANSION BOARD OVERVIEW To AVOID damaging the circuit board, relays or accessories, DO NOT connect more than 42 Vdc (32 Vac) to the AUX relay contact terminal blocks. QUICK CLOSE Switch OFF: No change to the gate's normal operation. ON: When CLOSE EYES/Interrupt loop is deactivated it causes an opening or a stopped gate to close (ignores the Timer-to-Close).
Page 31: Accessory Features On Expansion Board
ADDITIONAL FEATURES ACCESSORY FEATURES ON EXPANSION BOARD ACCESSORY FEATURES ON EXPANSION BOARD Open Input (& common) Open command - opens a closed gate. Soft close (maintained switch does not override external safeties and does not reset alarm condition) (3-Button Control Station, If maintained, pauses Timer-to-Close at OPEN limit.
Page 32: Limit Setup With A Remote Control
ADDITIONAL FEATURES LIMIT SETUP WITH A REMOTE CONTROL LIMIT SETUP WITH A REMOTE CONTROL To set the limits using a remote control, first you will need a 3-button remote control that has been programmed for OPEN, CLOSE, and STOP. Refer to the Programming section.
Page 33: Limit Setup With A Remote Control
ADDITIONAL FEATURES LIMIT SETUP WITH A REMOTE CONTROL LIMIT SETUP WITH A REMOTE CONTROL ADJUST THE LIMITS If the limits have already been set the operator will exit the limit setting mode after resetting each limit. Set the Close Limit Only Press and release the SET OPEN and SET CLOSE buttons simultaneously to enter limit setting mode.
Page 34: Gate Operator Setup Examples
ADDITIONAL FEATURES GATE OPERATOR SETUP EXAMPLES GATE OPERATOR SETUP EXAMPLES The following are example setups for the gate operator. Your specific site requirements may be different. Always setup the operator system to the site requirements, including all necessary secondary entrapment protection systems. NOTE: We recommend that all accessories and board configurations are set on the primary operator. RESIDENTIAL SMALL One to four residential homes sharing a gated entrance/exit, allowing vehicle access trumps security concerns A residential community (more than four homes) having one or more gated entrances/exits, allowing vehicle access trumps security concerns...
Page 35: Liftmaster Internet Gateway
Internet Gateway will pair to the operator if it is within range and the operator will beep if programming is successful. The status as shown by the LiftMaster Internet Gateway app will be either “open” or “closed”. The gate operator can then be controlled through the LiftMaster Internet Gateway app.
Page 36: Troubleshooting
TROUBLESHOOTING CONTROL BOARD LEDS CONTROL BOARD LEDS The control board is equipped with many LEDs that have a variety of functions. The control board LEDs indicate the status of the operator, assist with programming, and diagnose potential problems with the operator. NOTE: When cycling or disconnecting power (ac/dc) to the control board, it is recommended that you unplug the J15 plug.
Page 37 TROUBLESHOOTING CONTROL BOARD LEDS CONTROL BOARD LEDS DIAGNOSTIC CODES LEDS YELLOW DIAGNOSTIC LED RED DIAGNOSTIC LED # BLINKS MEANING CORRECTION # BLINKS MEANING CORRECTION 1 BLINK Low Power Mode (not an error) 2 BLINKS Current Sense Motor control circuit fault, replace control board 2 BLINKS ID resistor failure...
Page 38: Troubleshooting Chart
TROUBLESHOOTING TROUBLESHOOTING CHART FAULT POSSIBLE CAUSES CORRECTIONS Operator does not a) No power to control board a) Check AC and battery power run and diagnostic b) Open fuse b) Check fuses LED not on. c) If on battery power only, low or dead batteries c) Charge batteries by AC or solar power or replace batteries d) Defective control board d) Replace defective control board...
Page 39 TROUBLESHOOTING TROUBLESHOOTING CHART FAULT POSSIBLE CAUSES CORRECTIONS Gate stops during a) Check DIAGNOSTIC LEDs a) Use Diagnostic code to identify issue travel and reverses b) Inherent force obstruction detection b) Check for obstruction in gate’s path or travel. Use manual disconnect, manually move immediately.
Page 40 TROUBLESHOOTING TROUBLESHOOTING CHART FAULT POSSIBLE CAUSES CORRECTIONS Photoelectric sensor a) Incorrect photoelectric sensor wiring a) Check photoelectric sensor wiring. Retest that obstructing photoelectric sensor causes moving gate to stop, and may reverse direction. Check Anti-Tail gate switch. does not stop or b) Defective photoelectric sensor reverse gate.
Page 41 TROUBLESHOOTING TROUBLESHOOTING CHART FAULT POSSIBLE CAUSES CORRECTIONS Quick Close not a) Quick Close setting incorrect a) Check that Quick Close setting is ON working correctly. b) CLOSE EYES/Interrupt loop detector or loop b) Check operation of CLOSE EYES/Interrupt Loop detector wire defective c) Replace defective Expansion board c) Defective Expansion board...
Page 42: Repair Parts
REPAIR PARTS INDIVIDUAL PARTS ITEM PART NUMBER DESCRIPTION NOT SHOWN K73-34718-2 Chassis K94-36250 Battery Harness (for 7AH batteries) K77-36480 Operator Cover with labels, keys, and lock K94-36531 Wiring Harness with ID Resistor assembly 30 Amp Fuses K76-34697 APS Encoder, 24V 1941240D #41 Chain (10 feet) K16-GT2-7...
Page 43: Repair Parts
REPAIR PARTS...
Page 44: Accessories
REMOTE CONTROLS Chamberlain offers a variety of LiftMaster remote controls to satisfy your application needs. Single-button to 4-button, visor or key chain. The following remote controls are compatible with operators manufactured by Chamberlain after 1993. Contact your authorized LiftMaster dealer for additional details and options.
Page 45: Accessories
ACCESSORIES MISCELLANEOUS WIRELESS ACCESS CONTROL RECEIVER Access control receiver for up to 450 remote controls. Model STAR450-315 HEATER Keeps operator gearbox and batteries at suitable temperature when outside temperature is below 0°F for extended periods of time. Models GHTRKITCSL (includes heater and bracket for optimal 7AH battery location) and G6518SL (replacement heater only) PLUG-IN LOOP DETECTOR Conveniently plugs into existing control board.
Page 46: Wiring Diagram
WIRING DIAGRAM To protect against fire and electrocution: For continued protection against fire: • DISCONNECT power and battery BEFORE installing or servicing operator. • Replace ONLY with fuse of same type and rating. Field Wiring Field Wiring Edge Interrrupt Black White White Yellow...
Page 47: Warranty
The Chamberlain Group, Inc. (“Seller”) warrants to the first purchaser of this product, for the structure in which this product is originally installed, that it is free from defect in materials and/or workmanship for a period of 7 year residential/ 5 year commercial from the date of purchase [and that the CSL24V™ and CSL24VH™ are free from defect in materials and/or workmanship for a period of 7 year residential/ 5 year commercial from the date of purchase].

This manual is also suitable for:

Liftmaster csl24vh

Chamberlain LiftMaster CSL24V Installation Manual

Safety

Introduction

Preparation

Installation

Wiring

Adjustment

Programming

Finish Installation

Operation

Additional Features

Maintenance

Troubleshooting

Repair Parts

Accessories

Wiring Diagram

Warranty

Quick Links

Troubleshooting

Need help?

Questions and answers

Related Manuals for Chamberlain LiftMaster CSL24V

Summary of Contents for Chamberlain LiftMaster CSL24V

This manual is also suitable for:

Table of Contents