Safety instructions Safety instructions Please follow these safety instructions closely to prevent accidents and material losses. Safety instructions explained & the Code of Practice of relevant trade associations, Danger & all current safety regulations as This symbol warns against the defined by DIN, EN, DVGW, TRGI, risk of injury.
Page 3
Instal- charge static loads. ling non-authorised compo- nents and non-approved modifications/conversion can compromise safety and may invalidate our warranty. For replacements, use only ori- ginal spare parts from Viessmann or those which are approved by Viessmann.
Further details regarding the individual steps ..........Parts lists Parts list Vitocell 300-B (300 litres).............. Parts list Vitocell 300-B (500 litres).............. 11 Parts list Vitocell 300-V (200 and 300 litres) ..........13 Parts list Vitocell 300-V (500 litres).............. 15 Commissioning/service reports ............... 17 Product parameters ..................
Commissioning, inspection, maintenance Steps - commissioning, inspection and maintenance For further information regarding the individual steps, see the page indicated Commissioning steps Inspection steps Maintenance steps Page • 1. Filling the DHW cylinder ........... . . •...
Commissioning, inspection, maintenance Further details regarding the individual steps Filling the DHW cylinder 1. Fill the DHW cylinder from the 2. Check the fittings on the heating DHW side. water and DHW side for leaks and tighten, if required. Note If the DHW cylinder is pressurised, 3.
Page 7
Commissioning, inspection, maintenance Parts list Vitocell 300-B (300 litres) Please note Pointed objects or those with sharp edges will damage the internal cylinder wall. Only use plastic tools to clean the inside. 6. Use a chemical cleaning agent to remove hard deposits that cannot be removed by a high pressure cleaner.
Page 8
Commissioning, inspection, maintenance Further details regarding the individual steps (cont.) Returning the DHW cylinder into use 1. Reconnect the DHW cylinder to the pipework. 2. Insert new gaskets H underneath flange lid E or cylinder cap F. 3. Refit flange lid E or cylinder cap F with stainless steel circular blank G and tighten with the required torque.
Parts lists Parts list Vitocell 300-B (300 litres) When ordering spare parts: 010 Sensor well (with item 009) Quote the type and serial no. (see 011 Sensor well thermal insulation type plate) and the item no. of the 012 Reducer required part (as per this parts list).
Page 10
Parts lists Parts list Vitocell 300-B (300 litres) (cont.)
Parts lists Parts list Vitocell 300-B (500 litres) When ordering spare parts: 011 Sensor fixture Quote the type and serial no. (see 012 Sensor well (with pos. 011) type plate) and the item no. of the 013 Reducer required part (as per this parts list).
Page 12
Parts lists Parts list Vitocell 300-B (500 litres) (cont.)
Parts lists Parts list Vitocell 300-V (200 and 300 litres) When ordering spare parts: 009 Sensor fixture Quote the type and serial no. (see 010 Sensor well (with item 009) type plate) and the item no. of the 011 Sensor well thermal insulation required part (as per this parts list).
Page 14
Parts lists Parts list Vitocell 300-V (200 and 300 litres) (cont.)
Commissioning/service reports Commissioning/service reports Commissioning Service Service date: Service Service Service date: Service Service Service date: Service Service Service date: Service Service Service date:...
Product parameters Product parameters Vitocell 300-B Cylinder capacity kWh/24 h 1.17 1.37 Standby heat loss with 45 K temperature differential (volume standby sec- tion) (volume solar sec- tion) Vitocell 300-V Cylinder capacity Standby heat loss kWh/24 h with 45 K temperature...
Vitocell 300-V, type EVI 200 l type EVI 300 l type EVI 500 l 11.4 Vitocell 300-B, type EVB 300 l type EVB 500 l 11.0 Capacity that can be heated with the electric im- mersion heater Vitocell 300-V, type EVI...
Certificates Declaration of conformity We, Viessmann Werke GmbH & Co KG, D-35107 Allendorf, confirm as sole responsible body that the products Vitocell 300-B and Vitocell 300-V comply with the following standards: DIN 4753 AD Codes of Practice This product is designated _-0036 in accordance with the following Directives:...
Need help?
Do you have a question about the VITOCELL 300-B and is the answer not in the manual?
Questions and answers