Advertisement
Advertisement
Table of Contents
Related Manuals for AGL EAGL 2000
Summary of Contents for AGL EAGL 2000
- Page 1 EAGL 2000 & EAGL 3000S Laser Levels Owner’s Manual...
-
Page 2: General Information
Thank you for buying the EAGL laser. Although it is very simple to use, we recommend that you read this manual before operating the laser. Specifications Operating range EAGL 2000: 2,000 ft. (600m) diameter EAGL 3000S: 3,000 ft. (900m) diameter Self-leveling range ± 4˚ (± 7%) Accuracy Better than ±1/16”... - Page 3 Safety label on COMPLIES WITH 21CFR 1040.10 side of laser AND 1040.11 EXCEPT FOR DEVIATIONS PURSUANT TO LASER NOTICE NO. 50, DATED JULY 26, 2001. CLASS 1 LASER PRODUCT EAGL 2000 Keypad EAGL 3000S Keypad Windy H.I. Alert Windy H.I. Alert On/Off...
-
Page 4: Operation
OPERATION Setup The laser mounts to any 5/8” x 11 tripod (flathead or domed) or can rest on any stable flat surface (floor, bricks, etc.). Position tripod, attach laser, then adjust tripod until rough leveled (within ±4° self-leveling range). Turning on the Laser Press the on/off key to power-up the laser. -
Page 5: Power Sources
After it has releveled, check if the beam elevation has changed from its original benchmark position. Press the H.I. key again to return to H.I. alert. Windy mode can be on on or off when H.I alert is used. Matching Slope (EAGL 3000S only) The EAGL 3000S can be used to match a single slope in X axis, up to 6% positive or 6% negative slope. -
Page 6: Battery Pack
BATTERY PACK Battery Unlock To replace the alkaline batteries, or to charge Button the NiCd pack, first remove the battery pack. The NiCd pack must be charged before first use. Removing the Battery Pack Battery Press the battery unlock button -- Release see (1) in the diagram at right. -
Page 7: Checking Calibration
Calibration should be checked regularly. For convenience you should establish a range for routine and quick checks. Your AGL dealer can assist you in setting up one. Allow at least 15 minutes of warm-up time before checking or adjusting calibration. - Page 8 LS100 DETECTOR For Grade Rod or Handheld Applications FRONT Choice of LCD (front) accuracy Choice of Detection sound level window On/Off Sound output Fast beep: LEDs: To turn on or off, Too low press “Accuracy” and Continuous: “Sound level” keys at On-grade the same time Slow beep:...
-
Page 9: Lcd Display
LCD DISPLAY Accuracy Sound Loud Normal No horn: Mute Fine Medium Wide Indicates that High LEDs are on On-grade Grade Battery status indication arrows Initial warning (see 11 channels below) Change batteries LEDs Grade can also be indicated by LEDs. Ideal for use in low light or above eye level, or for long range jobs like slope match. -
Page 10: Using The Detector
Using the Detector 1. Press On/Off key to turn on the detector. 2. Press top key to select the accuracy (deadband) and middle key to select sound level. (The detector retains in memory the last settings used.) 3. Turn the detection window towards the laser beam, and move the detector up or down according to the information given on the LCD display. -
Page 11: Detector Specifications
AGL’s sole obligation under this express warranty shall be, at AGL’s sole option and expense, to replace or repair the Product or part, or refund the purchase price paid for the Product. - Page 12 AGL or its distributors have been advised of the possibility of such damages, and limits its liability to replacement, repair, or refund of the purchase price paid, at AGL’s option. This limitation of liability for damages will not be affected if any remedy provided herein shall fail of its essential purpose.
Need help?
Do you have a question about the EAGL 2000 and is the answer not in the manual?
Questions and answers