Ansa RS-1 Installation & Operating Instructions Manual

Ansa roller door remote control unit

Hide thumbs

Table Of Contents

RS1 CONTROL UNIT

ATX-1 KEYFOB

LUX-4 KEYFOB

PHOTOELECTRIC CELL SAFETY SYSTEM

LIGHT GRID SAFETY SYSTEM

ALARM KIT

WIRELESS RADIO CODE SWITCH

WIRELESS RADIO KEY SWITCH

RS-1

Roller Door

Remote Control Unit

Installation

& Operating

Instructions

V7 Safety Grid January 09

Controlled by...

Ansa Door Systems Ltd

Table of Contents

Need help?

Do you have a question about the RS-1 and is the answer not in the manual?

Questions and answers

Summary of Contents for Ansa RS-1

Page 1 Roller Door LUX-4 KEYFOB Remote Control Unit PHOTOELECTRIC CELL SAFETY SYSTEM LIGHT GRID SAFETY SYSTEM Installation & Operating ALARM KIT Instructions V7 Safety Grid January 09 WIRELESS RADIO CODE SWITCH Controlled by... WIRELESS RADIO KEY SWITCH Ansa Door Systems Ltd...
Page 2: Table Of Contents
1 - General Description The ANSA RS1 control unit is designed to operate roller garage doors fitted with single phase tubular motor drives. Equipped with “rolling code” high security remote controls, allowing easy memorisation of up to fifteen transmitters. The unit has all the features needed for efficient, safe and reliable operation of roller doors including built-on courtesy lamp, operating button and multi- function red indicator LED.
Page 3: Fitting The Rs-1 Control Unit
WK-1 Wireless WB-1 Wireless Code Switch Key Switch Wall Button 3 - Fitting the RS-1 Control Unit BUILT -ON LIGHT The RS1 control unit is normally fitted on the same side as the motor MULTI-FUNCTION RED LED INDICATOR drive. Select a suitable position for the control unit, within sight of the door, well away from moving parts, ensuring that:- It can be plugged into an adjacent 13A switched socket.
Page 4: Electrical Connections
135mm of the screen at the free end. 4.8 Fitting the optional ANSA Alarm System (Type AL12/HW) Fix the alarm module alongside the left hand side of the RS1 Unit. Pass the connection lead through the right hand cable entry gland and connect the plug to the security alarm socket on the RS1 circuit board (see fig 8).
Page 5 BLACK WIRES - SIG WHITE WIRES - TEST BROWN WIRES - 24V DOOR CONTROLS CONNECTIONS FOR A STOP PUSH BUTTON PHOTO ELECTRIC CELL LG-01 ANSA PEC 3 LIGHT GRID Green LED indicates power Yellow LED indicates correct alignment Figure 10 Page 4...
Page 6: Photoelectric Cell Safety System (Optional)
6.1 Function The ANSA photoelectric cell (PEC) projects an invisible infra red beam across the door opening which is focused on a reflective lens target. Obstructions within the doorway blocking the safety beam are sensed and a safety signal is transmitted to the RS1 Control Unit.
Page 7: Light Grid Safety System (Optional)
7.1 Function The ANSA LG-01 Light Grid is an active safety system designed to monitor the closing operation of Roller Doors equipped with an ANSA RS-1 control unit. The equipment comprises an emitter (Tx) track and receiver (Rx) track which are mechanically fixed directly to the door guide tracks and electrically connected (low voltage) to the ANSA remote control unit.
Page 8: Alarm System (Optional)
· Fix the Alarm Module to th left of the RS-1 Control Unit using the plugs and screws provided. Pass the connection lead and plug through the right hand cable gland entry and route the cable as shown away from the radio receiver tile and connect the plug to the alarm socket on the RS1 circuit board.
Page 9: Commissioning
· Switch On to set limits the door (refer to Section 2.1) and Option Dip switch No. 3 on the RS-1 PCB will need to be switched on when carrying out limit switch adjustments. Open and close the door ensuring that at no time does the door curtain raise out of the door guides ·...
Page 10: Adding/Deleting Transmitters & Wireless Access Controls
10 Adding Transmitters & Wireless Access Controls Keyfobs supplied are normally preprogrammed . Extra keyfobs or other wireless access control devices are added as follows. Press the operating button for 5 seconds and release when the red LED indicator goes out. The LED will flash once to confirm Add Mode. Take the new transmitter to be added and press the button once.
Page 11 16 Problem Solving Guide LED Signal Door Status Cause Solution LED On Operational No fault Door in stand-by mode LED Off Door is not operational Power supply fault Test mains power supply and switch on or Reset circuit breaker Fuse in plug has blown Replace 5amp fuse in 3 pin plug (or spur unit) PCB fuses have blown Replace PCB main fuse (coloured white) 6.3amp 5mmx20mm...
Page 12: Technical Specifications
Web Site: www.ansadoorsystems.co.uk Technical Support Helpline: 0750 800 80 95 ANSA Door Systems Ltd. maintains a policy of continuous development and reserves the right to change the contents of this instruction guide without prior notice. The contents are intended for guidance only.