Void Infinite 7 V2 Owner's Manual
  1. Manuals
  2. Brands
  3. Void Manuals
  4. Amplifier
  5. Infinite 7 V2
  6. Owner's manual

Void Infinite 7 V2 Owner's Manual

Power amplifiers
Hide thumbs
Table of Contents

Advertisement

Quick Links

OWNER'S MANUAL
INFINITE 7 - 8 V2
POWER AMPLIFIERS
Infinite V2

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Infinite 7 V2 and is the answer not in the manual?

Questions and answers

Related Manuals for Void Infinite 7 V2

Summary of Contents for Void Infinite 7 V2

  • Page 1 OWNER'S MANUAL INFINITE 7 - 8 V2 POWER AMPLIFIERS Infinite V2...
  • Page 2 Infinite V2 IMPORTANT THE PRODUCT REQUIRES CLASS 2 OUTPUT WIRING. TO PREVENT ELECTRIC SHOCK, DO NOT Shock Hazard - Do Not Enter REMOVE TOP OR BOTTOM COVERS. Choc Hasard - N*entrent NO USER SERVICEABLE PARTS INSIDE. Schocke Hazard - Test Nicht REFER SERVICING TO QUALIFIED Betrete SERVICE PERSONNEL.
  • Page 3 Infinite V2 Features Rugged, touring grade chassis. E.I.A. Standard 19" (48.3cm) rack-mountable. Ultra reliable 'Super G' class output stage provides maximum stability even into 2 ohm loads. High efficiency triple rail voltage supply system. 'VSP' Velocity Sense Protection circuitry protects speakers from over excursion. 'CEP' Clip Elimination Protection prevents clipped waveforms from reaching the outputs.

  • Page 4: Front Panel

    Infinite V2 On -18 - 6 Current Draw (Amps) Infinite 8 Standby Power Front Panel 1.Power Switch Used to turn the amplifier on or off. 2.Standby LED Indicates that the amplifier is connected to the mains but has not been switched 3.Level Controls Used to control CH 1 &...

  • Page 5: Rear Panel

    Infinite V2 Inputs Out 1 : Pin 1+ : ch 1 + Out 2 : Pin 1+ : ch 1 + Serial No Pin 1 : Pin 1 - : ch 1 - Pin 1 - : ch 1 - Pin 2 : + Pin 2+ : ch 2 + Bridge Mode : out 1...

  • Page 6: Technical Specifications

    Infinite V2 TECHNICAL SPECIFICATIONS For Infinite models 7 - 8 v2 FREQUENCY RESPONSE ref.100W@8Ω 20Hz - 20kHz +0.05 dB / -0.08 dB THD ref. 4 Ω , 1KHz 0.015% S/N 20Hz-20kHz, ref full output 105 dB 1 Vrms INPUT SENSITIVITY INPUT IMPEDANCE 20kΩ...

  • Page 7: Worldwide Service

    Failure to do so could delay the repair of your product. Warranty Registration Please take time to fill out the warranty registration form at the back of this manual and return it to Void Acoustics. Environmental WEEE Mark If you want to dispose of this product, do not mix with general household waste.

  • Page 8: Bridge Mode

    Infinite V2 Notes Bridge Mode Connect to input 1 only and use the two CH1 speakon outputs or both + binding posts. Use +1 for signal + and +2 for signal - Minimum impedance in bridge mode must be 4 ohms, i.e.

  • Page 9: Limited Warranty

    Authorised Void Dealer) that it is free of defects in materials and workmanship and that each product will meet or exceed all factory published specifications for each respective model. Void agrees to repair or replace (at its discretion) all defective parts at no charge for labour or materials; subject to following provisions:...
  • Page 11 Void Acoustics Unit 15 Dawkins Road Ind Est Poole Dorset BH15 4JY...
  • Page 12 Unit 15 : Dawkins Road Ind Est Poole : Dorset : BH15 4JY : UK Tel: +44 (0)844 410 1440 Fax: +44 (0)844 410 1439...

This manual is also suitable for:

Infinite 8 v2

Table of Contents

Save PDF