Best CP35 series Installation Instructions Manual
Hide thumbs
Also See for CP35 series:
- Specification sheet (2 pages) ,
- Specification (1 page) ,
- Instructions manual (49 pages)
Table of Contents
Advertisement
INSTALLATION INSTRUCTIONS
HB0078
CP35 AND CP37 SERIES
INTENDED FOR DOMESTIC COOKING ONLY
!
!
READ AND SAVE THESE INSTRUCTIONS
INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER.
HOMEOWNER: USE AND CARE INFORMATION ON PAGES 12 and 13.
BEST; Hartford, Wisconsin www.BestRangeHoods.com 800-558-1711
REGISTER YOUR PRODUCT ON LINE AT: www.BestRangeHoods.com/register
For additional information - visit www.BestRangeHoods.com
SV08544 rev. A
Advertisement
Table of Contents
Related Manuals for Best CP35 series
Summary of Contents for Best CP35 series
- Page 1 READ AND SAVE THESE INSTRUCTIONS INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER. HOMEOWNER: USE AND CARE INFORMATION ON PAGES 12 and 13. BEST; Hartford, Wisconsin www.BestRangeHoods.com 800-558-1711 REGISTER YOUR PRODUCT ON LINE AT: www.BestRangeHoods.com/register For additional information - visit www.BestRangeHoods.com SV08544 rev. A...
- Page 2 Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter. To reduce the risk of fire and electrical shock, the Best models CP35 & CP37 Series should only be installed Use proper pan size. Always use cookware with their own built-in blowers.
- Page 3 - CP35 CP37 POWER PACK SYSTEM ODEL ODEL (8” R ROOF CAP OUND WALL CAP ODEL ODEL (10’’ IGH CAPACITY ROOF CAP ROUND WALL CAP ODEL (10” ROUND ADJUSTABLE ELBOW 8” R OUND ADJUSTABLE ELBOW 8” R OUND ODEL STANDARD DUCT (10”...
-
Page 4: Prepare The Installation
The minimum hood distance above cooktop must not be less than 24”. 10” in line vertical damper for CP37 A maximum of 30” above cooktop is highly recommended for best capture of 8” round adapter & damper cooking impurities. Wall for CP35 or 10”... - Page 5 4. MOUNT CUSTOM HOOD INTERNAL FRAMEWORK WARNING The framework must be positively secured to wall studs or other wooden framework behind the drywall. Make sure it is capable of supporting its own weight and the weight of the CP35 or CP37. Failure to do so may cause personal injury or damage to countertop or cooktop.
- Page 6 7. REMOVE THE BOTTOM PANEL Using a Phillips screwdriver, remove both bottom panel Disassemble bottom panel from power pack and set aside. retaining screws and set aside. ETAINING CREW OCATION HO0110 HO0111 SIDE VIEW 8. REMOVE THE KNOCK-OUT OPENING From inside the power pack, remove the wiring cover by removing two (2) retaining screws and set aside.
-
Page 7: Connect Wiring
10. CONNECT WIRING WARNING Risk of electrical shock. Electrical wiring must be done by qualified personnel in accordance with all applicable codes and standards. Before connecting wires, switch power off at service panel and lock service disconnecting means to prevent power from being switched on accidentally. Position the power pack below the installed custom hood. - Page 8 11. REMOVE THE BLOWER(S) (CONT’D) CP37 M LOWERS FRONT BRACKET ODEL For each blower, using a 5/16” socket, remove all blower mounting screws from the inner top of the power pack front and rear brackets. Set aside the screws. LOWERS REAR BRACKET HD0297 For each blower, slide it to disengage its flanges from the retaining brackets.
- Page 9 13. REINSTALL THE BLOWER(S) CP35 M ODELS Slide the blower to engage its flange in the retaining bracket. HD0293 OUNTING CREW OCATION Using a 5/16” socket, secure the blower to the inner top of the power pack with all blower mounting screws (previously removed in step 11).
-
Page 10: Reinstall Bottom Panel
14. REINSTALL BOTTOM PANEL Lift the bottom panel and engage the power pack metal tabs Secure the bottom panel to the power pack using its screws in bottom panel slots, as shown in details A and B below. previously removed in step 7. SIDE VIEW ETAINING CREW... -
Page 11: Reinstall Baffle Filters
16. REINSTALL BAFFLE FILTERS CAUTION Remove protective plastic film covering filters before installing them. NOTES : 1. On 42” width model only, reinstall both filter fillers previously removed in step 5. 2. Assemble the metal handles to the filters, using provided no. 8-32 x 1/4” screws, before installing them in the power pack. It is recommended to install side filters first and finish with center one(s). -
Page 12: Use And Care
18. USE AND CARE Baffle Filters The baffle filters should be cleaned frequently. Use a warm detergent solution. Wash more often if your cooking style generates greater grease—like frying foods or wok cooking. Remove baffle filters by pushing them towards the back of hood and rotating filters downward. Baffle filters are dishwasher safe. Allow filters to dry completely before reinstalling them in the power pack. -
Page 13: Operation
19. OPERATION Always turn your hood on before you begin cooking to establish an air flow in the kitchen. Let the blower run for a few minutes to clear the air after you turn off the range. This will help keep the whole kitchen cleaner and brighter. HC0039 HC0038 A) Halogen light knob... -
Page 14: Warranty
(c) describe the nature of any defect in the product or part. At the time of requesting warranty service, you must present evidence of the original purchase date. Best ® , 926 W. State Street, Hartford, WI 53027 (1-800-637-1453) www.bestrangehoods.com... -
Page 15: Wiring Diagram
21. WIRING DIAGRAM SPEED SWITCH CONTROL THERMOSTAT LINE NEUTRAL GROUND LAMP SWITCH COLOR CODE BLACK BLUE BROWN WHITE YELLOW LAMP LAMP HE0092A - 15 -... -
Page 16: Service Parts
22. SERVICE PARTS Best CP35 & CP37 Series HL0110 QTY. ( POWER PACK WIDTH ESCRIPTION 30” 36” 42” 48” 1 SV08543 A 8” R DAPTER AMPER OUND 2 SV08541 A 10” R DAPTER OUND 3 SV08097 I NTERNAL LOWER 4 SV05921 L &...
Need help?
Do you have a question about the CP35 series and is the answer not in the manual?
Questions and answers