Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for AURES ELIOS III G
Summary of Contents for AURES ELIOS III G
- Page 1 User Manual Version 1.0 May 2013 ELIOS III G...
- Page 2 Copyright 2013 All Rights Reserved Manual Version 1.0 The information contained in this document is subject to change without notice. We make no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose.
- Page 3 Safety IMPORTANT SAFETY INSTRUCTIONS To disconnect the machine from the electrical Power Supply, turn off the power switch and remove the power cord plug from the wall socket. The wall socket must be easily accessible and in close proximity to the machine. Read these instructions carefully.
- Page 4 CAUTION ON LITHIUM BATTERIES There is a danger of explosion if the battery is replaced incorrectly. Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer’s instructions. Battery Caution Risk of explosion if battery is replaced by an incorrectly type. Dispose of used battery according to the local disposal instructions.
- Page 5 The crossed dustbin symbol on the device means that it should not be disposed of with other household wastes at the end of its working life. Instead, the device should be taken to the waste collection centers for activation of the treatment, collection, recycling and disposal procedure.
- Page 6 Revision History Version Date Description May 2013 Initial release ...
-
Page 7: Table Of Contents
Table of Contents 1 Packing Checklist .........1 1-1 Standard Items ..............1 1-2 Optional Items ..............2 2 System View...........3 2-1 Front View & Rear view ............. 3 2-2 Side View................4 2-3 Bottom View............... 4 2-4 Rear I/O View..............5 2-5 Dimension................ -
Page 8: Packing Checklist
Packing Checklist Standard Items a. System b. power adapter c. power cord RJ45 to DB9 cable x 4... -
Page 9: Optional Items
Optional Items a. Magnetic Card Reader b. iButton Dallas Key Reader c. Magnetic Card + iButton Dallas key d. RFID Reader Reader e. Magnetic Card Reader + Biometric f. Addimat key reader Reader (fingerprint) g. VFD... -
Page 10: System View
System View Front View & Rear view Description Touch Screen VFD dummy cover Ventilation LED Light Stand... -
Page 11: Side View
Side View Description USB Connector Addimat Key Kit MSR Installation Slot (Remove cover to install) Power Button Bottom View Description System Box (easy access to the Motherboard) Thumb Screw of the System Box... -
Page 12: Rear I/O View
Rear I/O View Description Cash drawer USB (x4) LAN (10 / 100/1000) Serial COM (x4) 2nd VGA DC Jack Power button Dimension... -
Page 14: System Assembly & Disassembly
System Assembly & Disassembly Remove the Stand 1. Place the system face down. Make sure not to scratch the screen. 2. Remove the screw (x1) to release the plastic cover. 3. Disconnect the cable (x1) as shown. 4. Loosen the thumb screw (x1) fastening the metal bracket and the LCD rear cover. 5. -
Page 15: Remove The Motherboard
Remove the Motherboard To access the motherboard, you need to open the system box which is located in the bottom of the system. 1. Remove the screws (x4) that fix the system box to the stand. 2. Gently flip down the system box due to various connectors connecting to the motherboard. -
Page 16: Remove The Lcd Rear Cover
Remove the LCD Rear Cover To remove the LCD rear cover in order to access the touch board. Please remove the stand first as steps descried in Chapter 3-1. To open the rear cover of the LCD, please remove the screws (x10) as shown in the picture. -
Page 17: Replace The Touch Board
Replace the Touch Board Remove the stand (Chapter 3-1). Remove the rear cover (Chapter 3-3). Disconnect the cables (x6). Remove the screws (x3). Replace the Touch Screen Remove the stand (Chapter 3-1). Remove the rear cover (Chapter 3-3). Remove the screws (x7) and disconnect the touch cable (x1). Gently separate the touch screen from the LCD panel. -
Page 18: Replace The Lcd Panel
Replace the LCD Panel Remove the stand (Chapter 3-1). Remove the rear cover (Chapter 3-3). Remove the touch screen (Chapter 3-6). Disconnect the cable (x1). Remove the screws (x4) at both sides of the sheet metal LCD bracket and separate it from the LCD panel. -
Page 19: Peripherals Installation
Peripherals Installation HDD (Hard Drive Disk) Installation Loosen the thumb screws (x2) on the rear side and bottom side of the system to release the HDD cover. Slide out the top part and the bottom part of the HDD cover and disconnect the HDD cable (x1) to take out the HDD. -
Page 20: Msr And 2-In-1 Msr Installation
MSR and 2-in-1 MSR Installation The installation procedure for the MSR module is also valid for RFID Reader, iButton Dallas Key Reader, 2-in-1 MSR + iButton Dallas Key Reader, Fingerprint Reader and 2-in-1 MSR + Fingerprint Reader modules. Remove the screws (x2) to open the MSR dummy cover. Align the MSR module connector and mechanism parts to the system. -
Page 21: Addimat Key Kit Installation
Addimat Key Kit Installation Accessories of addimat key kit: a. Addimat board + Y cable (connecting the Y cable to the addimat key board first) b. Addimat Key with cable module Loosen the system box from the LCD module with stand by unfastening the screws (x4). - Page 22 Connect the addimat key with cable module (accessory b) to accessory a. Connect the other side of Y cable to the connector on the motherboard as the position as right picture shows. Fasten the screws (x4) of the system box again to fix the system box to the LCD module with stand.
-
Page 23: Vfd Installation
VFD Installation Open the VFD dummy cover and pull the VFD cable out. Slide the VFD module and fasten the screws (x2) to secure it to the system. Connect the VFD cable to the VFD module. Finally attach the plastic cover as shown in the picture. -
Page 24: Cash Drawer Installation
Cash Drawer Installation You can install a cash drawer through the cash drawer port. Please verify the pin assignment before installation. Cash Drawer Pin Assignment Signal DOUT bit0 DIN bit0 12V / 19V DOUT bit1 Cash Drawer Controller Register The Cash Drawer Controller use one I/O addresses to control the Cash Drawer. Register Location: 48Ch Attribute: Read / Write Size: 8bit... - Page 25 Bit 7: Reserved Bit 6: Cash Drawer “DIN bit0” pin input status. = 1: the Cash Drawer closed or no Cash Drawer = 0: the Cash Drawer opened Bit 5: Reserved Bit 4: Reserved Bit 3: Cash Drawer “DOUT bit1” pin output control. = 1: Opening the Cash Drawer = 0: Allow close the Cash Drawer Bit 2: Cash Drawer “DOUT bit0”...
-
Page 26: Specification
Specification Model ELIOS III G Motherboard CPU Supports Intel Cedarview D2550 1.8G, L2 1M (TDP 10W) Chipset Intel NM10 System Memory 1x S.O. DIMM socket, DDR3 FSB1067Mhz, 2G, (up to 4GB) Graphic Memory Intel GMA 3650 (Gfx frequency up to 640MHz), DX9... - Page 27 Model ELIOS III G Motherboard MSR ( PS2/COM) MSR + Fingerprint MSR (PS2/COM)/Fingerprint (USB) MSR (PS2 )/ iButton (PS2 /COM) MSR + iButton MSR (COM) / iButton (PS2) iButton iButton Reader (PS2/COM) Customer Display 2x20 slim type VFD (USB) Power Power Supply Ext.
-
Page 28: Configuration
Configuration C56 Motherboard... -
Page 29: Connectors & Functions
Connectors & Functions Connectors Functions LVDS Inverter Connector System FAN Connector LVDS Connector Power LED Connector SATA LED Connector Speaker & MIC Connector SATA Power Connector COM5(Touch) Connector CN10 Printer Port Connector CN11/12 USB Port(Internal) CN13 LAN LED Connector CN14 PS2 Keyboard Connector CN15 Card Reader Connector(COM6) -
Page 30: Jumper Settings
Jumper Settings Cash Drawer Power Setting Function (1-2) (3-4) ▲+19V +12V Inverter Selection Function (1-2) (3-4) (5-6) ▲LED CCFL COM2 Power Setting Function (1-2) (3-4) No Power ▲COM2 +5V COM2 +12V LCD ID Setting LVDS Output Resolution (1-2) (3-4) (5-6) (7-8) (9-10) Bits Channel Interface... - Page 31 COM 3 & COM4 Power Setting Function (1-2) (3-4) (5-6) (7-8) ▲COM3 +5V COM3 +12V ▲COM4+ 5V COM4 +12V COM2/COM3/COM4 Power Setting COM2, COM3 and COM4 can be set to provide power to your serial device. The voltage can be set to +5V or 12V by setting jumper JP5 and JP6 on the motherboard.
-
Page 32: Appendix
Appendix Drivers Installation: To download the most recent drivers and utilities, and obtain advice regarding the installation of your equipment, please visit the AURES Technical Support Website: www.aures-support.fr (French) www.aures-support.fr /UK(English) www.aures-support.fr /GE (German)
Need help?
Do you have a question about the ELIOS III G and is the answer not in the manual?
Questions and answers