Table of Contents
Advertisement
TV Wireless Headphones
Item No. 201771
Introduction
Congratulations on your purchase of the Sharper Image TV Wireless Headphones. Thanks to the
latest FM Wireless technology, you will soon be enjoying great audio quality with complete
freedom of movement. Please read this guide to install and use the equipment properly, and keep
it for future reference.
Important
Before using the TV Wireless Headphones for the first time, please ensure that the batteries are
fully charged for about 16 hours. This will guarantee a longer operating lifetime of the batteries.
General Information
Function and Capability
1. RF/FM wireless transmission
The transmitter sends the stereo audio signal from your audio or video source to the headphones
without wires. The headphones receive the signals through walls, doors and windows. The
Headphones use high radio frequency as the signal carrier, ensuring clear and crisp reception.
Multiple headphones can be used at the same time with a single transmitter.
2. Automatic rechargeable system
The transmitter automatically recharges the rechargeable batteries in the headphones. Simply
place the headphones on the transmitter with the recharging contact on the transmitter and
headphones connected. The green LED will light up during recharging. After the batteries are
fully charged, the green LED light will turn off.
3. Volume control
A volume controller is located on the left headphone. Simply adjust the knob for desired volume
level.
4. Applications
The RF/FM Wireless Stereo Headphone System is compatible with TVs, stereo systems, VCRs,
DVD players, CD players, MP3 players, iPods, computers and all other audio and video
equipment.
Advertisement
Table of Contents
Related Manuals for Sharper Image TV Wireless Headphones
Summary of Contents for Sharper Image TV Wireless Headphones
- Page 1 Please read this guide to install and use the equipment properly, and keep it for future reference. Important Before using the TV Wireless Headphones for the first time, please ensure that the batteries are fully charged for about 16 hours. This will guarantee a longer operating lifetime of the batteries. General Information Function and Capability 1.
- Page 2 Simply use the included RCA to 3.5mm cable. 7. Connection Method 2: Headphone output jack 8. TV Wireless Headphones can be also be connected to an audio source from its headphone output jack. Use the included RCA to 3.5mm cable OR the 3.5mm to 3.5 mm cable.
- Page 3 Headphones (Figure 2) 1. Power switch and indicator The red LED lights up when it is powered on and in use. 2. Turning selector and indicator When there is hissing sound through the headphones, push the selector to obtain the proper channel.
- Page 4 Use only one of the audio inputs, either the 3.5mm stereo headphone audio input or the line audio input. Using both audio inputs at the same time may damage your TV Wireless Headphones. Connect the 3.5mm stereo plug of the line audio cable to the transmitter’s 3.5mm headphone input.
- Page 5 Use only one of the audio inputs, either the 3.5mm stereo headphone audio input or the line audio input. Using both audio inputs at the same time may damage your TV Wireless Headphones. Connect the 2 RCA plugs of the line audio cable to the transmitter’s audio inputs.
- Page 6 Use only one of the audio inputs, either the 3.5mm stereo headphone audio input or the line audio input. Using both audio inputs at the same time may damage your TV Wireless Headphones. Connect the 3.5mm stereo plug of the audio cable to the transmitter’s audio input.
- Page 7 output level, adjust the line output level of the audio source to the highest acceptable undistorted level. The red LED will stop lighting up after the audio source has been disconnected for 1 minute. Switch on the headphone. You may hear a hissing sound through the headphones if the device is not yet properly tuned to the Transmitter.
- Page 8 Push the tuning selector on headphones until the clear sound is obtained. The red LED will keep flashing during the selection. When the proper channel is obtained, the red LED will remain lit. NOTE: On some newer TV sets, it may be necessary to turn on or increase the volume of the headphone jack the audio out jack.
- Page 9 Headphones Drivers Full range 40mm dia. Frequency response 20-20,000 Hz Impedance 32 Ohms Sensitivity 105dB @ 1KHz Signal-to-noise ratio > 60dB Distortion < 1% Channel separation > 30dB Power supply 3V (2 x LR03, AAA, NiMH) Dimensions 185 x 165 x 75mm Safety Instructions •...
- Page 10 You are cautioned that changes or medications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. CUSTOMER SERVICE If you require any additional assistance with your TV Wireless Headphones, please call 1 (877) 714-7444, and select Option 3.
Need help?
Do you have a question about the TV Wireless Headphones and is the answer not in the manual?
Questions and answers
instead of a steady blue light and sound, I **** getting a flashing blue light and no sound on the headphones
I charged batteries, turned on...blue light flashing but no sound with olume turned up all the way
The Sharper Image TV Wireless Headphones may not be producing sound despite the blue light flashing and the volume being turned up due to the following reasons:
1. Low Battery – The batteries in the headphones might be running low. Place the headphones on the transmitter to recharge them.
2. Audio Source Not Switched On – Ensure that the connected audio source is turned on.
3. Volume Too Low – Check if the volume on the audio source is set too low and adjust it to an appropriate level.
4. Improper Tuning – The headphones may not be properly tuned to the transmitter. Push the tuning selector on the headphones until the correct channel is found.
5. Interference or Distance Issue – If the headphones are too far from the transmitter or there is interference from fluorescent lamps or other audio sources, move closer to the transmitter or relocate the devices to reduce interference.
This answer is automatically generated