Quick Setup Guide - Samsung 750 Series User Manual

Quick Setup Guide

Congratulations on the purchase of your new Samsung TV. Read this
setup guide to get your TV up and running quickly.
1-800-SAMSUNG (1-800-726-7864)
STOP Samsung Electronics America, Inc.
105 Challenger Road Ridgefield Park, NJ 07660-0511
Please do not return this unit.
Samsung Electronics Canada Inc.
If you have problems operating your
55 Standish Court Mississauga, Ontario L5R 4B2
TV, call:
1-800-SAMSUNG (1-800-726-7864) Call Center hours of operation: Mon-Sun, 9:00 AM -12 AM EST.
To register this product, visit:
Getting Started
Step 1 :
Install the Stand
Make sure to distinguish between the front and back of the Stand and Guide
Stand when assembling them.
Make sure that at least two people lift and move the LCD TV.
Stand the product up and fasten the screws. If you fasten the screws with the LCD
TV placed down, it may lean to one side.
1 2
Guide Stand
Bottom View
Stand
Screw Top View
3
Rear
Step 2 :
Install the Batteries into the Remote
To install batteries into your remote control, follow these steps:
1. Lift the cover on the back of the remote upward
as shown in the figure to the right.
2. Install two AAA batteries.
Make sure to match the + and - ends of
the batteries to the diagram in the battery
compartment.
3. Replace the cover.
Step 3 :
Connect Power and Antenna or Cable
Connect ANT IN to:
or
Power Input
Use a 75 ohm (round) cable.
Make sure the AC power cord
is plugged in securely to the
wall outlet and the TV.
Step 4 :
Connect External Devices
Connecting an AV device (Blu-ray player, cable/satellite box, etc.)
connections. Note that many digital cable programs are not in HD. Check with your video
provider to ensure your are receiving HD signals.
Audio/Video connection (480i only)
Using an Audio/Video Cable
VCR
VIDEO OUT AUDIO OUT
VCR / DVD / Blu-ray player / Cable Box /
Satellite receiver
Lowest Quality Connection
Step 5 :
Run Plug & Play
When you turn on your TV for the first time, it automatically launches the Plug &
Play function. With Plug & Play, you can select the On Screen Display language,
set the clock mode, and launch the TV's channel memorizing process. It also
displays connection instructions similar to those in this guide.
To navigate while Plug & Play is running, press the Up, Down, Left or Right
arrow buttons on your remote. To make a selection, press the
To skip a screen, press the MENU button.
To turn on your TV, press the POWER button on the remote or press the
POWER button on the TV. To run Plug & Play, follow these steps:
Plug & Play
Select Language of the OSD.
English
Español
Language : E
Français
U Move E Enter
1. On the Language screen, select the language for the On Screen Display
(OSD) using your remote control, and then press
Home Use screen appears.
2. Select Home Use, and then press ENTERE
Demo, the TV will reset your picture and audio settings every 30 minutes. After
you press ENTERE button, the Antenna Source screen appears.
3. If your TV is only attached to an antenna, select Air. If your TV is only
Antenna or
attached to cable and you have no cable box, select Cable. If your TV is
attached to an antenna and cable with no box, select Auto. When done,
box Ant or Cable
Out
press ENTERE button on your remote. The Select Cable System screen
appears.
IMPORTANT: If your TV is attached to a cable or satellite box, skip Steps
3 through 5. After Plug & Play is complete, set your TV to Channel 3 or 4,
according to the directions for your cable or satellite box.
4. If your TV is attached to a cable system and you have no cable box, you
must select your cable system type. If you have Digital cable, you must
select the cable system type for both Analog and Digital.
The HDMI connection carries
digital video and audio.
When connecting to AV IN 1 on the back of your TV,
the AV IN 1
video cable (yellow).
After you have selected the cable system type, select Start, and then
press the ENTERE button on your remote.
Most cable systems are Standard (STD) systems. If you are not sure
about what kind of cable system you have, contact your cable company.
5. The TV memorizes the available channels. This process can take up
to 45 minutes. After the TV has memorized the channels, the Clock Mode
ENTERE button. screen appears.
6. Choose the Clock Mode. Select Auto if you have a digital channel in
your area. Select Manual if you don't, or if you have a cable or satellite box.
When done, press ENTERE
If you select Manual, the clock setting screen appears.
7. Select the Daylight Saving Time setting: Off, On, or Auto, and then press
ENTERE button.
8. After the time zone screen, The connection method for best HD screen quality
is displayed. Press Right arrow button on your remote to view each screen in
succession. Press the BLUE
9. The Enjoy your TV screen appears. and then press
ENTERE button. The
Basic Functions
button. If you select Store
Changing the Screen Size
Your TV has several screen size options, each designed to work best with specific
types of video input. If you have a cable box or satellite receiver, it may have its
own set of screen sizes as well.
To change the screen size, press the
you press it, your TV displays the current setting. Thereafter, each time you press
the P.SIZE button, you change the size of the picture on the screen.
English - 1
Connecting an audio device
Connect your TV to your Home Theater or other audio
HD connection (up to 1080p)
Using an HDMI Cable
Device
HDMI OUT
HD Satellite receiver (STB)
Best Connection
HD connection (up to 1080p)
Using an DVI to HDMI Cable
DVI OUT
Device
AUDIO OUT
Connecting a PC
Satellite receiver (STB)
Connect your TV to a PC to use it as a Monitor.
Very Good Connection
Component connection (up to 1080p)
Using a Component Cable
AUDIO OUT COMPONENT OUT
Device
Good Connection
The following sizes are available:
16 9 Wide screen
button. The Daylight Savings screen appears.
Wide Fit
Screen Fit displays a full HD picture covering the entire screen with no cutoff
on any side. It is only available when your TV inputs an HDMI (720p, 1080i,
1080p), Component (1080i, 1080p), or DTV (over-the-air 1080i) signal.
Changing the Picture Mode
button to skip this section.
ENTERE button.
designed to give you an excellent picture under specific conditions.
The Picture Modes are listed and described in the table below:
Mode
Dynamic
Standard
Natural
Movie
To change the Picture Mode, follow these steps:
1. With the TV on, press the
P.SIZE button on your remote. The first time
The Tools menu appears.
2. Using the
3. On the Picture Mode menu, use the
the Picture Mode you want.
4. Press the
Analog Audio connection
Using an Audio Cable
Device
AUDIO IN
Amplifier / DVD Home Theater
Digital Audio connection
Using an Optical Cable
Digital Audio System
OPTICAL
HD connection
Using an HDMI Cable
AUDIO OUT DVI OUT
PC
Using an D-Sub Cable
PC OUT AUDIO OUT
PC
Zoom 1 Zoom 2
4:3 Standard screen Screen Fit
Description
sunny room.
TOOLS button on your remote.
or on your remote, select Picture mode.
or on your remote to select
EXIT button to exit the menu.