Walkera V450D01 User Manual
  1. Manuals
  2. Brands
  3. Walkera Manuals
  4. Toy
  5. V450D01
  6. User manual

Walkera V450D01 User Manual

Helicopter 2.4ghz
Hide thumbs Also See for V450D01:
1
2
3
4
5
6
7
8

Advertisement

Table of Contents

USER GUIDE - SUPPLEMENTAL
C
ONTENTS
5
Instructions for RX2702V receiver .................................................................................................................. 2
5.3
Channel connection of receiver ............................................................................................................ 2
10
Walkera V450D01 Flybarless System Setting RX2702V ............................................................................. 3
10.5
Flybarless system setting ...................................................................................................................... 3
10.5.1
Swashplate mechanical travel and neutral point setup ............................................................... 3
10.5.2
Swashplate mixing set-up for Elevator and Aileron servo travel ................................................. 4
10.5.3
Elevator and aileron gyro function normal/reverse setting ......................................................... 6
10.5.4
Rudder travel setting and check-UP ............................................................................................. 6
10.5.5
Rudder gyro reverse switch setting .............................................................................................. 7
10.5.6
Flybarless system setting test ....................................................................................................... 8
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the V450D01 and is the answer not in the manual?

Questions and answers

Related Manuals for Walkera V450D01

Summary of Contents for Walkera V450D01

  • Page 1 USER GUIDE - SUPPLEMENTAL ONTENTS Instructions for RX2702V receiver ........................2 Channel connection of receiver ......................2 Walkera V450D01 Flybarless System Setting RX2702V ................3 10.5 Flybarless system setting ........................3 10.5.1 Swashplate mechanical travel and neutral point setup ............... 3 10.5.2...
  • Page 2 RX2702V NSTRUCTIONS FOR RECEIVER 5.3 C MODE 2 HANNEL CONNECTION OF RECEIVER USERS ONLY AILE CAUTION: Please note that when using a MODE 2 transmitter set-up PIT and AILE servos are inverted compared to the original manual. There are 2 options to correct this: 1) Physically move the servos in the helicopter frame 2) Switch the AILE and PIT servo channel plugs on the receiver Failing to make this switch will make the system appear to move as if using a mix of transmitter modes.
  • Page 3 10 W V450D01 F RX2702V ALKERA LYBARLESS YSTEM ETTING 10.5 F LYBARLESS SYSTEM SETTING CAUTION: Unplug the wires connecting the ESC to the main motor to avoid the accidental movement of the main rotor. Reconnect when set-up is complete. ...
  • Page 4  Step 4: Main blade pitch setting The recommended pitch range is ±10°; the flight limit is ±11°. CAUTION: The adjustment of servo travel in a CCPM system must be made using the transmitter ‘SWASHMIX’ function, do not adjust the servo travel individually. 10.5.2 S WASHPLATE MIXING SET UP FOR...
  • Page 5  Step 3: Swashplate aileron travel setting With the AILE LED flashing GREEN the receiver is ready to accept the maximum limit of AILE input. Without moving any of the other controls push the aileron control stick of the transmitter to the far right position, while keeping max AILE, press the “SET”...
  • Page 6 10.5.3 E LEVATOR AND AILERON GYRO FUNCTION NORMAL REVERSE SETTING  Step 1: Elevator gyro reverse switch setting Tilt the helicopter forward and check if the gyro corrects the motion by tilting the swashplate aft. If it tilts to the front move the ELEV GYRO DIP switch to the other position.
  • Page 7 To check the correct operation of the rudder direction move the rudder stick on the transmitter left and right. Full right rudder should set the pitch of the tail blades to move the tail left and the nose right as it rotates about the main shaft axis. ...
  • Page 8 10.5.6 F LYBARLESS SYSTEM SETTING TEST  Step 1: Make sure everything is off and all receiver leads are connected. Make sure main motor leads are still disconnected  Step 2: Turn on the transmitter power and connect the helicopter main battery, wait for binding to complete.

Table of Contents