Scheppach TIGER2000S Assembly And Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Scheppach Manuals
  4. Grinder
  5. TIGER2000S
  6. Assembly and operating instructions manual

Scheppach TIGER2000S Assembly And Operating Instructions Manual

Wet grinder
Hide thumbs

Advertisement

Table of Contents

# W859
28-9-12
WET GRINDER
TIGER2000S
ASSEMBLY AND OPERATING INSTRUCTIONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
MADE IN CHINA

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TIGER2000S and is the answer not in the manual?

Questions and answers

Related Manuals for Scheppach TIGER2000S

Summary of Contents for Scheppach TIGER2000S

  • Page 1 # W859 28-9-12 WET GRINDER TIGER2000S ASSEMBLY AND OPERATING INSTRUCTIONS Due to continuing improvements, actual product may differ slightly from the product described herein. TO PREVENT SERIOUS INJURY, READ AND UNDERSTAND ALL WARNINGS AND INSTRUCTIONS BEFORE USE. MADE IN CHINA...
  • Page 2 PAGE 2...

  • Page 3: Personal Safety

    grounded in accordance with all codes and ordinances. Never remove the grounding prong or modify the plug in any way. Do not use any adapter plugs. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. If the tools should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user.

  • Page 4: Specific Safety Rules

    footing and balance enables better control of this product in unexpected situations. Use safety equipment. Wear eye protection when assembling and using this product. TOOL USE AND CARE Disconnect the Power Cord Plug from the power source before making any adjustments, changing accessories, or storing the Wet Grinder.
  • Page 5 Maintain a safe environment. Keep the area well lit. Make sure there is adequate surrounding space. Always keep the area free of obstructions, grease, oil, trash, and other debris. Do not use an electrically powered product in areas near flammable chemicals, dusts, and vapors. Never leave the Wet Grinder unattended when it is plugged into an electrical outlet.
  • Page 6 and other construction activities, contain chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: lead from lead-based paints, crystalline silica from bricks and cement or other masonry products, arsenic and chromium from chemically treated lumber. Your risk from these exposures varies, depending on how often you do this type of work.
  • Page 7 PAGE 7...

  • Page 8: Operating Instructions

    SYMBOLOGY UNPACKING When unpacking, check to make sure all the parts shown on the Parts List on page 17 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. OPERATING INSTRUCTIONS NOTE: For additional information regarding the parts listed in the...
  • Page 9 PAGE 9...
  • Page 10 TOOL SUPPORT (23) KNOB WATER TANK (21) (41) POWER SWITCH (34) WITH SAFETY KEY KNOB (21) TOOL SUPPORT (23) WATER TANK (41) TOOL SUPPORT HONING WHEEL (23) (27) KNOB TOOL BLADE (15) (NOT INCLUDED) KNOB SUPPORT PLATE (15) (16) ABRASION PASTE (43) PAGE 10...
  • Page 11 blade (sharp end downward) in the Support Plate. Then firmly tighten the two Knobs to secure the tool blade in place. (See Figure J, previous page.) Adjust the Tool Support (23) so that the Support Plate (16) is no more than 1/16” from the Grinding Stone (19) or Honing Wheel (27).
  • Page 12 When necessary, remove the Holder (6) from the Tool Support and readjust (downward) the Tool Support (23) so that the knife blade again lightly touches the Grinding Stone (19) or Honing Wheel (27). (See Figure K, previous page.) When finished grinding/honing the knife blade, remove the Holder (6) from the Tool Support (23).
  • Page 13 Grinding Tips: After you have set the angle, turn on the Wet Grinder and begin the grinding process. Press the tool evenly onto the Grinding Stone (19) near the cutting edge, and move the tool crosswise across the Stone. Make sure that at least half the width of the cutting edge comes into contact with the Grinding Stone at any time to avoid damage to the Stone.

  • Page 14: Inspection, Maintenance, And Cleaning

    INSPECTION, MAINTENANCE, AND CLEANING WARNING! Make sure the Wet Grinder is disconnected from its electrical outlet prior to performing any inspection, maintenance, or cleaning procedures. Before each use: Inspect the general condition of the Wet Grinder. Check for cracked or broken parts, damaged electrical wiring, damaged Grinding Stone or Honing Wheel, and any other condition that may affect safe operation.

  • Page 15: Please Read The Following Carefully

    To clean: Use a mild detergent or mild solvent to clean the exterior of the Wet Grinder. Do not immerse the machine in liquid. When storing, make sure to store the Wet Grinder in a clean, dry, safe location out of reach of children and other unauthorized people. CAUTION! All maintenance, service, or repairs not mentioned in this manual must only be performed by a qualified service technician.

  • Page 16: Assembly Diagram

    ASSEMBLY DIAGRAM NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. PAGE 16...
  • Page 17 PAGE 17...

Table of Contents