Complete Sprayer Parts List - Hydro-Force Flexi Pro User Manual

Safety and General Maintenance
• Run fresh water through the sprayer after each day of use to flush chemical from
the pump and hoses.
• Keep chemical containers and strainer screen clean.
• Keep charger connected to sprayer and plugged into to van power supply when
not in use to maintain fully charged battery. See Charging section for details.
• While sprayer and pump are made with chemical resistant materials, and can
handle a wide range of chemicals, do not assume chemical compatibility.
• Contact your distributor or the manfacturer if you have questions regarding your
chemicals compatibility.
• No warranty, expressed or implied, can be considered where component failure is
caused by chemical effects.
• Label all containers to properly identify chemicals.
• Do not use to spray liquids with temperatures above 160°F. (71°C)
• Do not use to spray flammable or combustable liquids.
• Do not use sprayer where flammable vapors are present.
• Pump can run dry without damage.
• If stored in possible freezing conditions the sprayer must be liquid free or
winterized with anti-freezing chemical.
• Do not operate without inlet strainer.
Charging
The Flexi Pro Sprayer is the strongest, best built 12 volt sprayer on the market. With
proper use, the Flexi Pro's robust "non-memory" battery will give long, reliable
service. Two chargers are included with each Flexi Pro Sprayer. Proper use of these
chargers is required to get the maximum use from the Flexi Pro battery.
The NM4132 Car Charger is included with the Flexi Pro Sprayer. It can be plugged
into the vehicle cigarette lighter or accessory power outlet and connected to the
Flexi Pro Sprayer to "top-off" the battery charge between jobs. The vehicle must be
running to produce the voltage required for proper charging. The NM4118 Adapter
with Alligator Clips is an optional accessory that can be used to connect the Flexi
Pro Car Charger directly to your truckmount or van battery for charging. The
truckmount or vehicle must be running to produce the voltage required for proper
charging.
The NM4130 Wall Charger is included with the Flexi Pro Sprayer. This charger is
plugged into an 110v wall outlet and connected to the Flexi Pro Sprayer when
longer charging times are required to fully charge the battery. A heavily discharged
battery may require 4 -8 hours to regain a full charge. The NM4130 Wall Charger
Complete List of Parts
12
PART # DESCRIPTION
AP64 Water Pump
NM4100 Battery
NM4114 Coil Hose, 15'
NA030 Spray Gun
NA0833 Extension
B281 Veejet 8005 ¼" FPT
NM4102 Bottle
NM4103 Cap
NA0840 Strainer
NA0839 Barb Nylon
NA0817 Tubing ¼" ID Vinyl
NM4104 Axle Cap
NM4105 Wheel
NM4110 Extendable Handle
NM4106 Base Plate
NS123 Hose Clamps
NS162 Elbow Barbs
NM4130 Power Recepticle
NM5124 Screws Power Recepticle
NM5793 Nuts Power Recepticle
NM4138 Switch Rocker
PA079A Connector (Butt 14-16ga)
NM4317 Connectors
NM4039 Connectors
NM5020 Wire Red
XHA07 3/8" Aluminum Axle Rod
NM4113 Molded Plastic Body
BR335 Quick Male
BR337 Quick Female
B006 Upholstery TeeJet 6501
NM4116 Rubber Bushing 3/8"
QUANTITY PART # DESCRIPTION
1 NM4061 Base Plate Screws
1 NM4061 Handle Screws
1 BR112 Coupling ¼" FXF
1 NM4115 Pump Base Bolts
1 NM4028 Pump Base Nuts
1 NM4255 Pump Base Washers
1 NA0802 Strainer Body
1 NA0803 Strainer
1 NA0826 Teejet Cap
1 NM4074 Double Stick Tape
60" AW17D Battery Hold Down
2 NM4140 Screw Battery Hold Down
1 NM4028 Nut Battery Hold Down
1 NM4255 Washer Battery Hold Down
1 NM4132 Car Charger (included)
4 NM4130 Wall Charger
2 NM4117 Rubber Bushing 3/4"
1 NM4064 Washer Spacer
4 Fuse 5 Amp -ATO
4 Fuse Holder
1 BR060 Hose Splicer 1/4" Barbs
2 NM4118 Car Charger Adapter w/
2 Aligator Clips
(F .25" 10-12ga)
2
(F .18" 14-16ga)
48 inches
16.75"
1
2
1
1
3
5
QUANTITY
6
4
1
2
2
2
1
1
1
12 inches
1
2
2
2
1
1
2
4
1
1
1
optional