S t a t u s L i g h t s B y p a s s Q u i c k E x i t Concord Security System (Software Version 3.1) Installation Instructions...
Page 2
4,855,713. Except expressly provided herein, the purchase of this product shall not constitute a license or otherwise provide a right to practice a method covered by any of the identified patents. GE Interlogix hereby grants the purchaser of this product a limited, non-exclusive license to practice the methods patented in the identified patents solely with products manufactured, sold or licensed by GE Interlogix.
Contents About This Manual Special Installation Requirements ......................1 UL Listed Installations..........................1 SIA System Requirements ........................2 Central Station Reporting ........................4 UL Canada Listed Installations....................... 4 California State Fire Marshall Listed Installations ................. 4 Planning the Installation Standard Panel ............................4 SuperBus 2000 Touchpads..........................
Page 5
Basic System Commands.......................... 66 Testing Zones/Sensors ..........................67 If a Wireless Sensor Does Not Test ...................... 67 Testing Phone Communication......................... 67 Testing Central Station/Pager Communication..................68 Testing Outputs and Sirens ........................68 Testing Light Control..........................69 Testing the Energy Saver Module (ESM)....................69 Changing Fixed Display LCD Touchpad Chime and Trouble Beep Tones ..........
About This This manual provides information for planning, installing, programming, and testing this security system. When necessary, this manual refers you to other documentation included with compati- Manual ble peripherals. Planning sheets are included for you to record hardware layout and software programming set- tings.
• Hardwire Smoke Detector: System Sensor models 2100D, 2100TD, 2100S, 2100TS, 2400, or 2400TH learned into sensor group 26 or Sentrol (ESL) models 429AT, 521B or 521BXT learned into sensor group 26 • Wireless Smoke Sensor 60-506-319.5 or 60-848-02-95 learned into sensor group 26 •...
Page 8
The following table describes non-programmable (hard coded) system operation as required to meet ANSI-SIA CP-01 and is provided only for your reference. Function Operation Disarm During Entry Delay Enter Code Only (or 1 + CODE) Cancel Alarm Enter Code Only (or 1 + CODE) Abort Annunciation Enabled Cancel Report Annunciation...
Central Station Reporting The panel has been tested with the following central station receivers using SIA and Contact ID reporting formats: • CS-5000 Central Station Receiver • Sur-Gard Central Station Receiver with models SG-DRL2A and SG-CPM2 UL Canada Listed Installations This section describes the requirements for CUL (UL Canada) Listed installations.
• 8 Supervised Hardwire Zones: Inputs for various hardwired detectors. Zone 8 can be set up in programming to accept 2-wire smoke detectors. • Built-In SuperBus 2000 Receiver (60-792-01-95R only): Allows use of up to 16 or 32 319.5 MHz. crystal and/or SAW Learn Mode wireless sensors and touchpads. Also allows supervision of Supervised Wireless Sirens.
• 4 Output SnapCard: Provides four form C relay outputs that can be set up to activate other signalling devices, based on system events, schedules, or direct control. • 4Z Input/2 Output Combo SnapCard: Provides three hardwire zone inputs, one two wire smoke detector loop, and two outputs that can be set up to activate other signalling devices, based on system events, schedules, or direct control.
Determine the Panel Location Note (A) Class 2, Class 3, and Before permanently mounting the panel, determine panel location using the following guidelines: power-limited fire alarm cir- cuits must be installed using • Centrally locate the panel with relation to detection devices whenever possible, to help FPL, FPLR, FPLP, or substi- reduce wire run lengths and labor.
Page 13
Table 1: Maximum Device Wire Length and Current Draw (Continued) Max. Wire Length Max. mA Device to Panel Draw 22 ga.—300 ft. SuperBus 2000 Fixed Display Touchpad 65 mA 18 ga.—700 ft. 22 ga.—1,100 ft. SuperBus 2000 RF Receiver 30 mA 18 ga.—2,800 ft.
Table 3: Minimum Device Current Draw Device Min. mA Draw SuperBus 2000 RF Receiver 27 mA SuperBus 2000 Phone Interface/Voice Module 25 mA Power Line Carrier Card 4 Input/2 Output SnapCard 20 mA 8Z Hardwire Zone Expander SnapCard 38 mA 4 Output SnapCard 1 mA SuperBus 2000 8Z Input Module...
Mounting Holes Knockout Knockout Mounting Holes Figure 2. Mounting the Panel Identify Panel Before installing devices and making wiring connections, familiarize yourself with the main panel components. Figure 3 shows the main component locations for the hardwire circuit board Components and the main component locations for the combination hardwire/wireless circuit board.
Connecting the Panel to Earth Ground Note For best results, it is recom- For maximum protection from lightning strikes and transients, connect the lower-left circuit mended that you crimp a board screw to earth ground as shown in Figure 5. Use 16-gauge, solid copper wire from an earth spade lug on the wire end at the panel and secure the lug grounded cold water pipe clamp to the panel.
Installing Optional SnapCards The SnapCard Header on the right side of the panel allows for the installation of one SnapCard. Install the desired SnapCard onto the panel SnapCard Header and secure it in place with two screws, included with the card (see Figure 8). Connect all necessary input/output wiring using the Installation Instructions included with the card.
• ESL models 429AT, 521B, 521BXT—(models 521B and 521BXT require the following dip switch settings: 1-on, 2-off) Use only the 2-wire smoke detector models described above. Alarm signals from other detectors may not be processed correctly if the panel has lost AC power and is operating only from the backup battery.
Connecting Speakers The panel provides one siren driver output for intrusion (steady), fire (temporal 3), and auxiliary Note Install all sirens/speakers (on-off-on-off) alarm sounds. This output trips only for partition 1 alarms. indoors, in a concealed loca- The output can drive a single 8-ohm speaker or multiple speaker circuit of 8-ohms or higher (as tion.
Not Used Panel Not Used Terminals Speaker Figure 12. Connecting Two Hardwire Interior Speakers w/Dual Speaker Units to Panel Terminals Connecting Piezo Sirens Output 1 Onboard output 1 (OUT 1—terminal 9) is an open-collector (switched path-to-ground), program- mable output that can handle a maximum of 200 mA current sink. The default setting (01614) activates the output 15 seconds after a police or fire alarm condition occurs.
Interior Exterior Panel Terminals Panel Terminals Black +12V Out 1 2k Ohm Resistor 49-454 Black Figure 13. Connecting Exterior and Interior Sirens Slim Line Hardwire Interior Siren (60-483-01) Note The volume switch settings Connect the siren to the panel as shown in Figure 14. inside the siren do not affect the siren output.
Enter program mode and set the partition House Code to the desired setting (see the LIGHT menu in the section “Programming the Panel”). CONTROL Proceed to the SIREN OPTIONS menu and set the SWS Supervision Code to the desired set- Note When installing Supervised ting.
GND +12V A Bus B SuperBus 2000 Fixed Display Touchpad or LCD Alphanumeric Touchpads Figure 16. Connecting Touchpads to the Panel Installing SuperBus 2000 Modules SuperBus 2000 modules can be installed inside the panel cabinet or away from the panel. Use the following guidelines when installing modules inside the panel cabinet (see Figure 17): •...
G N D + 1 2 V B U S Panel Terminals Receiver Module Terminal Strip + 1 2 V G N D Figure 18. Wiring the SuperBus 2000 RF Receiver SuperBus 2000 Phone Interface/Voice Module (60-777-01) The Phone Interface/Voice Module includes two backplates for mounting the module inside the control panel cabinet.
Wiring—Speaker (Status Voice Messages Only) Note To prevent status voice mes- Connect an interior speaker to the Phone Interface/Voice module terminals as shown in sages from being broadcast Figure 21. When connected as shown, the speaker only produces status voice messages. In an outside, do not connect alarm situation the speaker will announce voice status messages.
+12V B GND Z1 ZCOM Module Wiring Terminals Panel Terminals +12V A BUS B UL-Listed Normally UL-Listed Open (N/C) Normally Contacts Closed (N/C) in Parallel Contacts in Series 2.0K Ohm EOL Resistor 01-022 (Install at Last Contact) Figure 26. Connecting the Wireless Gateway Module to the Panel Setting Device Address on SuperBus 2000 Devices When the panel is powered up it automatically assigns device addresses and unit numbers to SuperBus 2000 devices, enabling the panel and module to communicate.
Check the phones on the premises for dial tone and the ability to dial out and make phone calls. If phones do not work correctly, check all wiring and correct where necessary. Proceed to the “Troubleshooting” section of this manual if problems persist. RJ-31X Jack TELCO...
Alphanumeric touchpads display , then , and finally a ************ SCANNING BUS DEVICES date and time display. To permanently mount the transformer, unplug it and remove the existing screw securing the Note If alphanumeric touchpads AC outlet cover. don’t display anything, immediately unplug the transformer and disconnect the backup battery.
Table 6: Touchpad Button Functions Button Programming Function Enters pauses when programming phone numbers. Deletes certain programmed settings. 0 thru 9 Enter numeric values wherever needed. 1 & 2 Select off (1) or on (2) wherever needed. 1 thru 6 Press and hold to enter alphabetical characters A thru F for account numbers.
Programming Tier 1 Menu Items This section guides you through programming tier 1 menu items as they appear in sequence. The exact order you follow will depend on whether you’re installing a new system or changing pro- gramming in an existing system. Demo Kit Mode (System Programming) (Default = off) This setting determines whether the panel is used for a standard installation (off) or as a demo kit (on).
Programming Tier 2 Menu Items This section guides you through programming tier 2 menu items as they appear in sequence. Figure 31 shows the menus available on tier 2. Each menu on tier 2 represents a group of settings related to the menu name. Some tier 2 menus break down into settings that affect the whole system (global) or a specific partition.
Page 33
Dealer Code (0002) Security-Global (Default = none) ¾ The 4-digit dealer code is used to prevent unauthorized per- To program a Dealer Code: sons from changing the programmed central station phone With the display showing , enter the DEALER CODE **** numbers.
Page 34
Quick Exit (partition 1: 0012, partition 2: 0022) Security-Partition 1-2 (Default = on) ¾ To turn Quick Exit off or on: This setting determines whether or not users can open and close a standard entry/exit door without causing an alarm (while the system is armed). With the display showing QUICK (current setting),...
Keyswitch Sensor (partition 1: 0015, partition 2: 0025) Security-Partition 1-2 (Default = none) ¾ To assign a Keyswitch Sensor: This feature lets users arm and disarm the system using either a keyswitch wired to a hardwire zone input or a wireless door/window sensor. With the display showing KEYSWITCH (current sensor number),...
Page 36
Phone Number (cs phone 1: 0100, cs phone 2: 0110, Phones-CS 1-3 (Default = none) cs phone 3: 0120) ¾ This setting is used for programming the central station receiver phone number. To program a Central Station Phone Number: Phone numbers can be 1 to 24 digits long, including pauses or * and # characters. With the display showing PHONE To enter pauses, press C.
Page 37
Exception Rpts (cs phone 1: 0103, cs phone 2: 0113, Phones-CS 1-3 (Default = off) cs phone 3: 0123) ¾ When this setting is on, the panel reports to the central station if the sys- To turn Exception Reports off or on: tem is not armed or disarmed at the specified schedule times.
Page 38
Phone Number (pager 1: 0130, pager 2: 0140, pager 3: Phones-Pager Phone 1-5 (Default = none) 0150, pager 4: 0160, pager 5: 0170) ¾ This setting is used for programming a phone number that communicates To program a Pager Phone Number: to a pager.
Page 39
Open/Close Rpts (pager 1: 0134, pager 2: 0144, pager 3: Phones-Pager Phone 1-5 (Default = off) 0154, pager 4: 0164, pager 5: 0174) ¾ This setting determines whether opening and closing reports are sent to a To turn Opening/Closing Reports off or on: pager.
Phone Options Menu menu lets you set up system phone access and communications that affect PHONE OPTIONS the whole system (global) or a specific partition. The following describe how to program the phone option settings that appear under GLOBAL Phone Test (02000) Phone Options-Global (Default = on) ¾...
Page 41
DTMF Dialing (02004) Phone Options-Global (Default = on) ¾ To turn DTMF Dialing off or on: This setting determines whether the panel uses DTMF tones (on) or pulse (off) for dialing programmed phone numbers. With the display showing DTMF DIALING OFF/ (current setting), press 1 (off) or 2 (on).
Page 42
Call Wait Cancel (02009) Phone Options-Global (Default = none) ¾ To set up Call Wait Cancel: This feature lets you set up a dialing prefix to disable the call waiting feature before the panel makes its first dialing attempt to any pro- With the display showing CALL WAIT CANCEL grammed central monitoring station or downloader phone number.
Page 43
Ring/Hang/Ring (partition 1: 0212, partition 2: 0222) Phone Options-Partition 1-2 (Default = on) ¾ To turn Ring/Hang/Ring access off or on: This setting determines how the panel picks up (seizes) the phone line. Select “on” if an answering machine shares the phone line with the panel. Select With the display showing RING/HANG/ “off”...
Phone Access Key (partition 1: 0216, partition 2: 0226) Phone Options-Partition 1-2 (Default = #) ¾ This setting determines which touch-tone phone button is used for system To change the Phone Access Key: access and control. With the desired partition selected, press A or B until the display shows PHONE If the Local Phone Control feature is enabled, the user can pick up the phone...
Page 45
Next Phone Test (0303) Timers-Global (Default = 7 days) ¾ To set the Next Phone Test: This setting is used by the Auto Phone Test feature (see PHONE OPTIONS— ) to determine when the next automatic phone test should occur. GLOBAL With the display showing NEXT PHONE TEST...
Extended Delay (partition 1: 0312, partition 2: 0322) Timers-Partition 1-2 (Default = 4 min.) ¾ To set the Extended Delay: This setting determines how much time the user has (after arming the sys- tem) to enter or exit the premises through a “designated extended delay With the display showing EXTENDED DELAY n door”...
House Code (partition 1: 0401, partition 2: 0411) Light Control (Defaults: partition 1=01-B, partition 2=02-C) ¾ This setting enables X10 controlled lights to work in a selected parti- To set the House Code: tion without interfering with the X10 controlled lights of the other With the desired partition selected, press A or B partition.
Star Is No Delay (partiton 1: 0514, partition 2: 0524) Touchpad Options-Partitions 1-2 (Default = off) ¾ This setting determines whether the keychain touchpad star button To change the keychain Star Is No Delay setting: controls an output (off) or the No Delay feature (on). With the display showing STAR IS NO DELAY OFF/ON (current setting), press 1 (off) or 2 (on).
Page 49
Note Press # and the display shows the new setting. As with all GE Interlogix panels, hardwire smoke detectors connected to Concord or SnapCard hardwire zones do not send restorals. Two Trip Error (06008) Reporting-Global (Default = off) ¾...
Page 50
AC Failure (06010) Reporting-Global (Default = off) ¾ To turn AC Failure reports off or on: When this setting is on, the panel reports to the central station 15 minutes after AC power to the panel is lost. With the display showing (current AC FAILURE OFF setting), press 1 (off) or 2 (on).
Page 51
Program Report (06015) Reporting-Global (Default = off) ¾ When this setting is on, the panel sends a report to the central sta- To turn Program Report on or off: tion when someone enters or exits installer programming. With the display showing PROGRAM REPORT ON/ (current setting), press 1 (off) or 2 (on).
Page 52
Force Armed (partition 1: 06105, partition 2: 06205) Reporting-Partition 1-2 (Default = off) ¾ To turn Force Armed off or on: When this setting is on, the panel reports to the central monitoring station when a user “force arms” the system. With the display showing FORCE (current setting),...
System Tamper (partition 1: 06109, partition 2: 06209) Reporting-Partition 1-2 (Default = off) ¾ This setting determines how the panel handles possible tamper situations. When To change the System Tamper setting: this feature is on, the panel reacts in the following two ways: With the display showing SYSTEM (current setting),...
SWS Supv Code (0703) Siren Options-Global (Default = 3) ¾ This setting determines the system house code number used for supervising wireless To set the SWS Supv Code: sirens. With the display showing (current code), SUPV CODE nnn Note enter the desired code (1–255). To supervise wireless sirens, Concord hardwire panels must include a SuperBus 2000 RF Receiver.
Page 55
Table 7: How to Trip Sensors Sensor Steps to Trip Sensor Handheld Wireless Touchpads Press the BYPASS button. Press and hold the lock and unlock buttons together until the Keychain Touchpads touchpad LED flashes. Press and release the unlock button twice quickly, then press and hold until the LED flashes three times.
Sensor Test (081) Sensors (Default = none) ¾ Use the following guidelines to “name” zone and sensor loca- To program Sensor Text: tions: Press A or B until the display shows SENSOR TEXT Press # and the display shows TEXT FOR SN 01 •...
Page 57
Audio Verify (0900) Audio Verification-Partition 1(Default = off) ¾ To turn Audio Verification off or on: This setting determines whether or not the system can be accessed by phone for alarm With the display showing , press #. The display shows AUDIO VERIFICATION verification.
Beep Delay (0905) Audio Verification-Partition 1(Default = 02 sec.) ¾ This setting determines how long AVM access To change the Beep Delay: beeps are delayed (0–300s, in 2-second intervals) at With the display showing , press A or B until AUDIO VERIFY OFF/ON the beginning of a 2-way audio session.
Device ID Acc. Modules-Bus Devices-Unit ID-Change ID (Default = none) ¾ This menu lets you change the bus To change a Device ID: device ID number when replacing With the display showing the desired bus device, press # + #. The display shows a defective bus device.
Key Beeps Acc. Modules-Bus Devices-Unit ID-Keypad Options (Default = on) ¾ This setting determines whether or not selected touchpads To turn Key Beeps on or off: beep when their buttons are pressed. With the display showing the desired touchpad, press # then A or B until the display shows KEYPAD OPTIONS This feature is usually turned off for a touchpad that is...
Output Programming (output 1: 101001, Acc. Modules-SnapCards-Output Programming (Defaults: Partition Assign=all, Configuration Output 1= 01400, output 2: 101011, output 3: 101021, Output 2 = 00410, Output 3 = 00903, Output 4 = 01003) output 4: 101031) ¾ This setting lets you assign a partition and a 5-digit To assign configuration numbers to SnapCard Relay outputs (where tttrr is the point configuration number, ttt is the trigger configuration number for each SnapCard relay out-...
Page 62
Smoke Verify (1100) Onboard Options-Inputs (Default = off) ¾ To turn Smoke Verify off or on: This setting controls the number of sensor group 26 (fire) zone trips needed to report a fire alarm. With the display showing , press # ONBOARD OPTIONS twice.
Output Text (Output 1: 1120, Output 2: 1121) Onboard Options-Output Text-Output 1, 2 (Default = none) ¾ Use the following guidelines to “name” onboard outputs: To program Output Text: With the display showing , press # then ONBOARD OPTIONS • Use the item numbers listed in “Appendix B, Table press B twice and the display shows OUTPUT TEXT...
Time (020) Time and Date (Default = 00:00) ¾ To set the Time: This setting lets you adjust the panel clock to the cor- rect time. The panel uses a 24-hour clock. For exam- With the display showing , press # and the display TIME AND DATE ple, to set the time to 4:17 ., enter 1617.
Page 65
Direct Bypassing User Codes-Reg. User Codes-User NNN (Default = off) (030nnn1 where nnn=user number 00-229) ¾ This setting determines whether To turn user code Direct Bypassing off or on: or not a specific user code pro- With the display showing , press # and the display shows USER CODES REGULAR USER...
Latchkey Report User Codes-Reg. User Codes-User NNN (Defaults: 00-05 = on, 06-229 = off) (030nnn5 where nnn=user number 00-229) ¾ This setting determines whether To assign the Latchkey Report attribute to user codes: or not the user code causes a With the display showing , press # and the display shows USER CODES...
Touchpad Brightness (042) Options (Default = 2) ¾ This setting lets the user lighten or darken the background on To adjust Touchpad Brightness: touchpad displays. Each touchpad can be set to compensate for Press A or B until the display shows OPTIONS lighting conditions in the touchpad location.
Set Up Schedules (05XXY, where (Default = 00:00) XX=schedule 00-15 and Y=start [0]/stop[1] 0 thru 8-Monday thru Sunday [2-8])) ¾ This menu lets you set up start/stop times for each day of To set up a Time Schedule: the week. Press A or B until the display shows SET UP SCHEDULES Press # and the display shows...
Page 69
Exception Reports (Opening: Attach Schedules to Events (Default = off) 062nn, Closing: 063nn, where nn=Schedule number [0 to 15]) ¾ This setting lets you attach the Exception To Attach a Schedule to Exception Opening or Exception Closing: Opening report feature and the Exception Press A or B until the display shows ATTACH SCHEDULES TO EVENTS Closing report feature to time schedules.
Energy Saver Menu menu lets you set the energy saver module low- and high-setpoints. These ENERGY SAVER setpoints determine when the module relay closes, thereby completing the circuit through the thermostat to the furnace/air-conditioner. Low Setpoint (070) Energy Saver (Default = 50°F) ¾...
Downloader Programming The panel can be programmed remotely using ToolBox. Use the information you recorded in Appendix A to inform the downloading operator of the programming requirements for this sys- tem. ToolBox Downloader Programming ¾ Note To initiate a ToolBox download session: A Downloader Phone Num- Contact your download station and ask the operator to prepare to download to the panel.
Table 9: Basic Touchpad Commands (Continued) Command System Response 7 + 7 + n (n = output number [1–6]) Turns the output on or off. (This command is only functional after output text is entered into panel 1–2 = onboard outputs memory.) 3–6 = module outputs 8 + CODE + 6...
Testing Central Station/Pager Communication After performing sensor and phone tests, check that the system is reporting alarms successfully to the central station or pager. Be sure to contact the central monitoring station before activating outputs that trigger from an alarm condition. Caution ¾...
Be sure to contact the central monitoring station before activating outputs that trigger from an alarm condition. Caution ¾ To test outputs: Contact the central monitoring station to inform them you are testing the system. Verify that all wiring at the panel and output devices is correct. Activate the appropriate device to trigger each output as programmed.
Press and hold 1 to lower the pitch or press and hold 2 to raise the pitch. Note Chime and trouble beep Release the button when the desired pitch is heard. tones sound using the After about 15 seconds of no touchpad activity, the steady tone stops sounding. default frequency during, or within 15 seconds of, any button activity at that specific...
10. Restore previous CS PHONE 1 settings if needed. Table 13: Current Phone Settings CS PHONE 1 Option Test Setting Previous Setting PHONE NUMBER Central station phone number HIGH LEVEL RPTS BACKUP OFF* CELLULAR BACKUP * Can be set to ON if no CS PHONE 2 PHONE NUMBER is programmed. Troubleshooting This section describes what to do if you experience problems with system operation.
Page 77
Feature Problem Action/Solution Check the AC circuit breaker to be sure the circuit is live. Check for proper panel and transformer wiring. Check that the transformer is plugged into a nonswitched outlet and secured with the provided screw. Check that the transformer is supplying AC to the panel. (Transformer internal fuse may be blown.
Page 78
Feature Problem Action/Solution Check that the premises phone line is working. Perform a phone test. Check that the DB-8 cord is plugged into the RJ-31X/CA-38A jack. Check that the DB-8 cord is wired correctly to the panel. Check for correct phone line wiring between the TELCO block and RJ-31X/CA-38A jack. Replace faulty RJ-31X/CA-38A jack.
Page 79
Feature Problem Action/Solution Check to make sure siren is not plugged into an outlet controlled by a switch. Move siren to a nonswitched outlet location and test. Panel doesn’t have a Power Line Carrier (PLC) card installed. Install PLC card. Panel is not powered by a power line carrier transformer.
Page 80
Feature Problem Action/Solution Wireless Touchpads System doesn’t respond to commands entered from wireless touchpad. Verify that receiver antennas are installed and connections are secure. Check that touchpad battery(s) are properly installed. Check the touchpad battery(s) for low voltage. Replace battery(s), if necessary. Use an RF Sniffer (60-401) to verify that touchpad is transmitting.
Page 81
Feature Problem Action/Solution Check that the module is wired correctly to the panel terminals. Verify the SuperBus Module’s red LED is flashing continuously. If the LED is not flashing, remove power and check wiring. Module is not controlling or communicating with the panel and panel indicates a “ ”...
Appendix A: Customer Name _________________________________ System Address _______________________________________ Planning City _________________ County ___________ State ___ Worksheets Zip __________ Phone (____) ___________ Table A1: Wireless Devices Part No. Description Qty. 60-362 Door/Window Sensor 60-670 SAW Door/Window Sensor 60-741-95 Micro Recessed Door/Window Sensor 60-499 Slim Line Door/Window Sensor 60-688...
Page 83
Table A2: Hardwire Devices Part No. Description Qty. Sub Total (Max.) Hardwire Sensors/Detectors 13-068 Magnetic Contact 3/8” press fit 13-070 Magnetic Contact – surface mount System Sensor models 2100D, 2100TD, 2100S, 2100TS, 2400, or 2400TH or ESL series 429AT, 10 mA 521B or 521BXT 13-082 PIR Motion Detector...
Page 84
Table A3: Zone and Sensor Assignments Module Bus Module Input RF Zone Group Partition Zone/Sensor Text ID Number Number Concord...
Page 85
Table A3: Zone and Sensor Assignments (Continued) Module Bus Module Input RF Zone Group Partition Zone/Sensor Text ID Number Number Concord...
Page 86
Table A3: Zone and Sensor Assignments (Continued) Module Bus Module Input RF Zone Group Partition Zone/Sensor Text ID Number Number Table A4: System Settings Index and Record Setting (reference) default Shortcut No. Setting Installer Programming—8 + Installer/Dealer CODE + 00 24 Hour Tamper Off 06000 AC Failure Off...
Page 87
Table A4: System Settings Index and Record (Continued) Setting (reference) default Shortcut No. Setting Dialer Abort On 02005 Dial Abort Delay 30 sec 02006 Disable Trouble Beeps Off 0701 Downloader Code 12345 0000 Downloader Phone No. None 0180 DTMF Dialing On 02004 Duress Code None 0017, 0027...
Page 88
Table A4: System Settings Index and Record (Continued) Setting (reference) default Shortcut No. Setting 0134, 0144, 0154, 1_____________2_____________3___________ Open/Close Reports (pagers) Off 0164, 0174 4_____________5_____________ Opening Reports Off 06100, 06200 1_____________2_____________ Onboard Output 1 01614- any audible alarm 11101 Onboard Output 2 01710 - status & alarm tones 11111 Output Trip Time 4 sec 0304...
Table A4: System Settings Index and Record (Continued) Setting (reference) default Shortcut No. Setting SWS Code 003 0703 System Tamper Off 06109, 06209 1_____________2_____________ Toll Saver On 0214, 0224 1_____________2_____________ TP Panic RPT FMT Off 06009 Two Trip Error Off 06008 Two Wire Smoke Off 1101...
Table B1: Sensor Group Characteristics (Continued) Name Application Alarm Delay PIR motion sensors that initiate a delay before going √ √ Delayed Interior Police Standard into alarm. * Local Instant 24-hour local alarm zone protecting anything that √ √ Police Instant 1, 2, 3 Interior...
Page 91
Table B2: Item Numbers and Sensor Text Sensor Sensor Sensor Item Item # Item # Sensor Text Item # Item # Item # Sensor Text Sensor Text Text Text Text Aborted Date North Siren Daughter’s Glass Sliding Access Degrees Goodbye Smoke Active Delay...
Page 92
Table B3: System Event Trigger Numbers System Event Description Trigger No. Null Trigger (used for direct control) Activated only by schedule or direct command. Fire Alarm When Fire sirens are started. Police Alarm When Police sirens are started. Auxiliary Alarm When Auxiliary sirens are started.
Page 93
Table B4: Sensor Number Event Trigger Numbers Sensor Number State Trigger No. State Trigger No. Sensor 11 in alarm open Sensor 12 in alarm open Sensor 13 in alarm open Sensor 14 in alarm open Sensor 15 in alarm open Sensor 16 in alarm open...
Page 94
Table B4: Sensor Number Event Trigger Numbers Sensor Number State Trigger No. State Trigger No. Sensor 53 in alarm open Sensor 54 in alarm open Sensor 55 in alarm open Sensor 56 in alarm open Sensor 57 in alarm open Sensor 58 in alarm open...
Page 95
Table B4: Sensor Number Event Trigger Numbers Sensor Number State Trigger No. State Trigger No. Sensor 95 in alarm open Sensor 96 in alarm open Table B5: System Feature Event Trigger Numbers Feature State Trigger No. Phone Test initiated AC Failure for 15 minutes CPU Low Battery detected (excluding first minute after power-up) 227...
Page 96
Table B7: Response Numbers Siren Response Response Trip Delay Tracking Time momentary 3 minutes siren time sustained momentary 3 minutes siren time sustained momentary 3 minutes siren time sustained momentary 3 minutes siren time sustained Notes for Table B7: Response Numbers If an event does not trigger sirens, siren tracking response numbers activate without turning Note The mechanical lifetime of...
Page 97
Appendix C: Settings To Enter Programming Mode: 8 + Installer or Dealer Code + 0 + 0 Tier 1 Menus Tier 2 Menus System Programming Security Phones (Continued) CS Phone 2 CS Phone 2 Global Partition 1 Partition 2 CS Phone 1 Demo Kit On Off Account...
Page 98
Tier 2 Menus (Continued) Phone Options Phones (Continued) Pager Pager Pager Pager Pager Downloader Global Partition 1 Partition 2 Phone 1 Phone 2 Phone 3 Phone 4 Phone 5 Phone Phone Test Local Phone Local Phone Phone Number Phone Number Phone Number Phone Number Phone Number...
Page 99
Tier 2 Menus (Continued) Timers Light Control Touchpad Options Global Partition 1 Partition 2 Partition 1 Partition 2 Global Partition 1 Partition 2 Entry Delay Sup vs. Time Entry Delay Entry Lights Entry Lights Latchkey Zones Fire Panic Fire Panic 30 secs (30-240) Rndm 1:00-4:00 30 secs (30-240)
Page 100
Sensor Partition Tier 2 Menus (Continued) Reporting Siren Options Sensors Learn Sensor Delete Edit Global Partition 1 Partition 2 Global Partition 1 Sensors Text Sensors Sensors 0 8 3 0 8 0 0 8 1 0 8 2 Immediate Sensor Text for Sn P1 Gnn 24-Hr Tamper...
Exit Delay • The low limit on Exit Delay (0311/0321) has been changed from 48 to 45 seconds, with the default setting changing from 64 to 60 seconds. Existing versions of Toolbox will still show a low limit of 48 seconds and a default setting of 64 seconds. When setting the Exit Delay in installer program mode, entering any number between 45 and 55 will result in an Exit Delay of 45 seconds and entering any number between 60 and 71 will result in an Exit Delay of 60 seconds.
Specifications Power Requirements: ..Class II, 24 VAC, 30 or 50 VA, 60 Hz Rechargeable Batteries: ..12 VDC, 4Ah Lead-Acid (part no. 60-681) OR 12 VDC, 7Ah (part no. 60-680). The battery will last 24 hours with no AC and specified standby load Radio Frequency: ....319.5 MHz Nominal Range: ....1000 feet (305 meters) typical open air Storage Temperature Range:- 30°...
System Wiring Refer to wiring diagram on next page. Notes Note 1 Class II power transformer must be plugged into an unswitched AC power receptacle. Do not short the transformer terminals together. The transformer contains an internal fuse that permanently disables the output if the terminals are shorted. Note 2 An alphanumeric touchpad is required for on-site programming.
Page 106
Z O N E 8 Z O N E C O M M O N Z O N E 7 Z O N E 6 Z O N E C O M M O N Z O N E 5 Z O N E 4 Z O N E C O M M O N Z O N E 3...
Need help?
Do you have a question about the Concord Security System and is the answer not in the manual?
Questions and answers