Listening To Radio Broadcasts; Tuning Radio Stations; Presetting Radio Stations Manually; Receiving Preset Stations - Kenwood KRF-X9050D Instruction Manual

Listening to radio broadcasts

The receiver can store up to 40 stations in the memory and recall them by
26
one-touch operation.
Radio stations can be classified into RDS (Radio Data System) stations
and other stations. To listen to or store RDS stations in the preset memory
see "Using RDS (Radio Data System)". (For U.K. only)

Tuning radio stations

MULTI CONTROL
TUNING 1/¡
TUNER
RC-R0714
1
Use the INPUT SELECTOR knob (TUNER key) to select the
tuner.
2
Use the BAND key to select the desired broadcast band.
Each press switches the band
as follows:
1 FM
2 AM
3
Use the AUTO key to select the desired tuning method.
Each press switches the tuning method as follows:
1 AUTO lit (auto tuning)
2 AUTO not lit (manual tuning)
• Normally, set to "AUTO" (auto tuning). If the radio waves are weak
and there is a lot of interference, switch to manual tuning. (With
manual tuning, stereo broadcasts will be received in monaural.)
4
Use the MULTI CONTROL knob or TUNING 1 / ¡ keys
to select the station.
Frequency
display
Auto tuning : The next station is tuned automatically.
Manual tuning : Turn the knob (or press the keys) to select the
desired station.
INPUT SELECTOR
BAND AUTO
MULTI
CONTROL
BAND
TUNING 1/¡
AUTO
TUNER
RC-R0715
"AM" or "FM" indicator appears
in the display.
FM AUTO SOUND DIGITAL
AM PRO LOGIC S.DIRECT
MHz 3 STEREO MONITOR
kHz DOWN MIX DSP TUNED
"AUTO" indicator lights
up in the display.
FM AUTO SOUND DIGITAL
AM PRO LOGIC S.DIRECT
MHz 3 STEREO MONITOR
kHz DOWN MIX DSP TUNED
"ST." lights up when a broadcast
is being received in stereo.
FM AUTO SOUND DIGITAL AUTO
AM PRO LOGIC S.DIRECT MEMO
MHz 3 STEREO MONITOR ST.
kHz DOWN MIX DSP TUNED
"TUNED" is displayed
when a station is received.

Presetting radio stations manually

The RDS auto memory function assigns preset numbers to RDS stations
starting from preset number "1". Therefore, be sure to execute the RDS
auto memory function before using the following operations to manually
store AM stations and other FM stations, and RDS stations. See "Presetting
RDS stations (RDS AUTO MEMORY)". (For U.K. only)
MULTI CONTROL
1
Tune to the station you want to store.
2
Press the MEMORY key while receiving the station.
Blinks for 5 seconds
SP A B TI.VOL
CLIP MUTE
BAND
RDS EON PTY
TP TA NEWS
AUTO
Proceed to step 3 within 5 seconds.
(If more than 5 seconds elapse, press the MEMORY key again).
3
Use the MULTI CONTROL knob or keys to select one of the
station presets (1 – 40).
4
Press the MEMORY key again to accept the setting.
• Repeat steps 1, 2, 3, and 4 to store as many stations as necessary.
• If you store a station at a previously used preset, the old station will
be replaced by the new one.
AUTO
MEMO
ST.

Receiving preset stations

AUTO
MEMO
ST.
1
Use the TUNER key to select the tuner as the source.
2
Enter the number of the preset you want to receive (up to
"40").
Press the numeric keys in the following order:
For "15", press .......... 0,5
For "20", press .......... 0,0,)
• If you make a mistake entering a two digit number, press the +10 key
repeatedly to return to the original display and start again.
SP A B TI.VOL
CLIP MUTE
RDS EON PTY
TP TA NEWS
MEMORY
Lights for 5 seconds
L C R
LFE SW
LS S RS
Numeric keys
TUNER
RC-R0714 RC-R0715
L C R
LFE SW
LS S RS
•
FM AUTO SOUND DIGITAL AUTO
AM PRO LOGIC S.DIRECT MEMO
ST.
MHz 3 STEREO MONITOR
TUNED
kHz DOWN MIX DSP
FM AUTO SOUND DIGITAL AUTO
AM PRO LOGIC S.DIRECT MEMO
ST.
MHz 3 STEREO MONITOR
TUNED
kHz DOWN MIX DSP