http://www.xiaoyu163.com 3 7 63 1515 0 SPECIFICATION AUDIO AMPLIFIER SECTION 22 W RMS × 4 Channels at 4 Ω and [< or =] 1% THD+N Power Output 80 dBA (reference: 1 W into 4 Ω) Signal-to-Noise Ratio 4 Ω (4 Ω to 8 Ω allowance) Load Impedance Equalizer Control Range Frequencies...
http://www.xiaoyu163.com SECTION 1 3 7 63 1515 0 PRECAUTIONS Safety Precautions Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system. Please use enough caution not to see the beam directly or touch it in case of an adjustment or operation check.
Page 4
http://www.xiaoyu163.com Preventing static electricity 3 7 63 1515 0 Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs. 1.2.1 Grounding to prevent damage by static electricity Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as CD players.
http://www.xiaoyu163.com SECTION 2 3 7 63 1515 0 SPECIFIC SERVICE INSTRUCTIONS This service manual does not describe SPECIFIC SERVICE INSTRUCTIONS. L 13942296513 u163 (No.MA162)1-5 http://www.xiaoyu163.com...
http://www.xiaoyu163.com SECTION 3 3 7 63 1515 0 DISASSEMBLY Main body section 3.1.1 Removing the front panel assembly (See Fig.1) (1) Push the detach button in the lower right part of the front panel assembly. Front panel assembly (2) Remove the front panel assembly. Detach button Fig.1 3.1.2 Removing the heat sink...
Page 7
http://www.xiaoyu163.com 3.1.3 Removing the top chassis assembly 3 7 63 1515 0 (See Figs.3 to 6) • Prior to performing the following procedures, remove the heat Bottom chassis assembly sink. Reference: Remove the front panel assembly as required. (1) From the bottom side of the main body, remove the two screws C attaching the top chassis assembly to the bottom chassis assembly.
Page 8
http://www.xiaoyu163.com 3.1.4 Removing the front chassis assembly 3 7 63 1515 0 (See Figs.7 and 8) • Prior to performing the following procedure, remove the front Top chassis assembly panel assembly, heat sink and top chassis assembly. (1) From the both sides of the top chassis assembly, remove the two screws F attaching the front chassis assembly.
Page 9
http://www.xiaoyu163.com 3.1.6 Removing the main board 3 7 63 1515 0 (See Figs.10 and 11) • Prior to performing the following procedures, remove the front Rear bracket panel assembly, heat sink and top chassis assembly. (1) From the rear side of the bottom chassis assembly, remove the two screws H attaching the rear bracket to the bottom chassis assembly.
Page 10
http://www.xiaoyu163.com 3.1.8 Removing the front door mechanism assembly 3 7 63 1515 0 (See Fig.13) • Prior to performing the following procedures, remove the front Bottom chassis Front door mechanism assembly panel assembly, heat sink, top chassis assembly and main board.
Page 11
http://www.xiaoyu163.com CD mechanism assembly section 3 7 63 1515 0 • Remove the CD mechanism assembly from the main body. (See "3.1.5 Removing the CD mechanism assembly".) 3.2.1 Removing the mechanism control board (See Fig.1) (1) From the bottom side of the CD mechanism assembly, sol- CD mechanism assembly der the short sections on the flexible wire.
Page 12
http://www.xiaoyu163.com 3.2.2 Removing the top cover 3 7 63 1515 0 (See Fig.2) (1) From the back side of the CD mechanism assembly, re- move the two screws B attaching the top cover. (2) Take out the top cover in an upward direction. Reference: When attaching the top cover, set the sections c of the top cov- er under the bending sections d of the chassis base 2.
Page 13
http://www.xiaoyu163.com 3.2.4 Removing the clamper unit 3 7 63 1515 0 (See Figs.5 and 6) • Remove the mechanism control board, top cover and mecha- Clamper unit 2 nism section. (1) From the bottom side of the mechanism section, remove the clamper 2 spring.
Page 14
http://www.xiaoyu163.com 3 7 63 1515 0 Clamper 2 spring CD chassis assembly Clamper unit 2 Fig.7 L 13942296513 Notch Clamper unit 2 Fig.8 Clamper unit 2 u163 Clamper spring Fig.9 1-14 (No.MA162) http://www.xiaoyu163.com...
Page 15
http://www.xiaoyu163.com 3.2.6 Removing the front unit 3 7 63 1515 0 (See Figs10 to 12) • Remove the mechanism control board, top cover and mecha- nism section. Flexible wire (1) From the bottom side of the mechanism section, remove the double-stick tape fixing the flexible wire. (See Fig.10.) (2) From the top side of the mechanism section, remove the screw D attaching the front unit 2.
Page 16
http://www.xiaoyu163.com 3.2.7 Removing the loading arm assembly 3 7 63 1515 0 (See Figs.13 and 14) • Remove the mechanism control board, top cover, mechanism Loading arm assembly section and front unit 2. (1) From top side of the mechanism section, move the loading arm assembly in the direction of the arrow.
Page 17
http://www.xiaoyu163.com 3.2.8 Removing the rod (L), rod (R) and roller assembly 3 7 63 1515 0 (See Figs.15 and 16) • Remove the mechanism control board, top cover, mechanism Collar Collar section, front unit and loading arm assembly. (1) From the bottom side of the loading arm assembly, release the rod (L) and (R) from the joints r.
Page 18
http://www.xiaoyu163.com 3.2.9 Removing the CD pickup 3 7 63 1515 0 (See Figs.17 to 19) • Remove the mechanism control board. CD mechanism assembly (1) From the bottom side of the CD mechanism assembly, turn the feed gear in the direction of the arrow to move the CD pickup assembly outwards.
http://www.xiaoyu163.com 3.2.10 Removing the spindle motor 3 7 63 1515 0 (See Fig.20) • Remove the mechanism control board, top cover, mechanism T. table assembly section and clamper unit. (1) From the top side of the mechanism section, remove the T.table assembly and washer from the spindle motor.
http://www.xiaoyu163.com 3.2.12 Removing the SW board and rest SW board 3 7 63 1515 0 (See Fig.23) • Remove the mechanism control board. CD mechanism assembly (1) From the bottom side of the CD mechanism assembly, re- move the screw L attaching the SW board. (2) Remove the screw M attaching the rest SW board.
(3) Digital tester Output Level Line out 5.0V (Vol. MAX) (4) Tracking offset meter (5) Test Disc JVC :CTS-1000 Dummy load (6) Extension cable for check Exclusive dummy load should be used for AM,and FM. For FM EXTDV001-20P × 1 dummy load,there is a loss of 6dB between SSG output and antenna input.The loss of 6dB need not be considered since...
Page 22
http://www.xiaoyu163.com Service mode 3 7 63 1515 0 4.2.1 Service mode setting (1) Tern ON power. (2) Pressing both the DISP button and BAND button. (3) Set to service mode CURSOR button : BACK CURSOR button : NEXT OK button : SET CURSOR SOURCE KD-SHX751...
Page 23
http://www.xiaoyu163.com 3 7 63 1515 0 CD DATA READ ADJ NOW ADJ INT OTHERS ADJ NOW ADJ NOW FEB ** FEO ** TEB ** RFG** The auto adjustment value of FGA ** TEO ** TGA ** survo at now ADJ INT ADJ INT FEB ** FEO ** TEB ** RFG** The auto adjustment value of...
Page 24
http://www.xiaoyu163.com 3 7 63 1515 0 PICTURE CLEAR NOW... PICTURE CLEAR A.DSP ERROR CLEAR NOW... A.DSP ERROR CLEAR T.DSP ERROR CLEAR NOW... T.DSP ERROR CLEAR ROM COLLECTION MAIN DATA CLEAR MAIN DATA CLEAR NOW... MAIN DATA CLEAR DSP TUNER S MODE VER=V*** SPI=** PI=**** ***.** SMI=***% PTY=** ******* MP=***%...
Page 25
http://www.xiaoyu163.com 3 7 63 1515 0 SMTH1=****** SMTH1=****** DEFAULT * BACK Select the value with ENTER : OK "CURSOR" button. SMTH2=****** SMTH2=****** DEFAULT * BACK Select the value with ENTER : OK "CURSOR" button. MP=****** MP=****** DEFAULT * BACK Select the value with ENTER : OK "CURSOR"...
Page 26
http://www.xiaoyu163.com 3 7 63 1515 0 7.FM IF COUNTER 7.FM COUNTER 97.9MHz 70dBuV 0% 97.9MHz 70dBuV 0% Adjustment NG or No Signal 8.AM S.METER 8.AM S.METER 999kHz 26dBuV 0% 999kHz 26dBuV 0% High or Low or No Signal 9.AM S.METER 9.AM S.METER 999kHz 56dBuV 0% 999kHz 56dBuV 0%...
Page 27
http://www.xiaoyu163.com 4.2.2 Error codes of panel mechanism 3 7 63 1515 0 PANEL ANGLE PANEL CLOSE MAIN BODY 10 degrees 20 degrees 30 degrees OPEN OPEN ERROR CODE ERROR CODE Details (SERVICE MODE) (NORMAL) OPEN error 0A01 1.Time out error by OPEN position cannot detect. CLOSE error (ANGLE 1 error) 0B06 1.Time out error by ANGLE 1 position cannot detect.
http://www.xiaoyu163.com SECTION 5 3 7 63 1515 0 TROUBLESHOOTING Feed section Is the wiring for IC601 Is 8V present at IC681 Is 2V at IC601 pin 63? Check CD8V. pin 63 correct? pins 3 and 12? Check the vicinity of IC601.
Page 29
http://www.xiaoyu163.com Signal processing section 3 7 63 1515 0 Compare the L-ch and Is the sound output from No sound from either R-ch to locate the both channels (L, R)? channel. defective point. Normal Is 9V present at IC165 Is 9V present at IC901 Check IC901 and its /IC265 pin 16? pin 10?
Page 30
http://www.xiaoyu163.com Maintenance of laser pickup 3 7 63 1515 0 Replacement of laser pickup (1) Cleaning the pick up lens Before you replace the pick up, please try to clean the lens Turn of the power switch and, disconnect the with a alcohol soaked cotton swab.
Page 31
16 PIN CORD DIAGRAM (for KD-AR7500) 3 7 63 1515 0 Black Green OR/WH Violet BL/WH Blue Gray WH White Yellow WH/BK Brown Orange GN/BK VI/BK GY/BK MEMORY 16 YL 8 BK 7 RD 15 OR/WH 13 BR 3 GN...
Page 32
http://www.xiaoyu163.com 16 PIN CORD DIAGRAM (for KD-SHX750) 3 7 63 1515 0 Black Green OR/WH Violet BL/WH Gray Blue WH White Yellow WH/BK Orange GN/BK VI/BK GY/BK MEMORY 16 YL 8 BK 7 RD 15 OR/WH 3 GN 11 GN/BK L 13942296513 2 VI 10 VI/BK...
Page 34
http://www.xiaoyu163.com 3 7 63 1515 0 L 13942296513 u163 Victor Company of Japan, Limited AV & MULTIMEDIA COMPANY CAR ELECTRONICS CATEGORY 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan (No.MA162) Printed in Japan http://www.xiaoyu163.com...
3 7 63 1515 0 SCHEMATIC DIAGRAMS CD/SD RECEIVER KD-AR7500, KD-SHX750 CD-ROM No.SML200504 Area suffix J ------------- Northern America L 13942296513 SOURCE KD-AR7500 DISP BACK BAND PICT MENU SOURCE KD-SHX750 DISP BACK BAND MENU PICT KD-AR7500 J KD-SHX750 J...
http://www.xiaoyu163.com 3 7 63 1515 0 Safety precaution Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system. Please use enough caution not to see the beam directly or touch it in case of an adjustment or operation check.
Page 37
http://www.xiaoyu163.com 3 7 63 1515 0 < M E M O > L 13942296513 u163 http://www.xiaoyu163.com...
Page 55
http://www.xiaoyu163.com 3 7 63 1515 0 < M E M O > L 13942296513 u163 http://www.xiaoyu163.com...
Page 56
http://www.xiaoyu163.com 3 7 63 1515 0 L 13942296513 u163 Victor Company of Japan, Limited AV & MULTIMEDIA COMPANY CAR ELECTRONICS CATEGORY 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan Printed in Japan (No.MA162SCH) http://www.xiaoyu163.com...
3 7 63 1515 0 PARTS LIST [ KD-AR7500 ] [ KD-SHX750 ] * All printed circuit boards and its assemblies are not available as service parts. Area suffix L 13942296513 J ------------- Northern America - Contents - 3- 2 Exploded view of general assembly and parts list (Block No.M1)
Page 58
http://www.xiaoyu163.com 3 7 63 1515 0 Exploded view of general assembly and parts list Block No. L 13942296513 68 31 Switch board u163 http://www.xiaoyu163.com...
Page 59
http://www.xiaoyu163.com 3 7 63 1515 0 Main board L 13942296513 u163 http://www.xiaoyu163.com...
Page 60
http://www.xiaoyu163.com 3 7 63 1515 0 General Assembly Block No. [M][1][M][M] Symbol No. Part No. Part Name Description Local GE20156-001A GEAR BKT UNIT LV40847-002A SPACER FSYH4036-100 SHEET GE30968-002A LEVER BKT UNIT GE30964-003A LOWER LEVER ASS LV35330-002A FRONT BKT ASSY QNZ0664-003 CAR CONNECTOR QAL0587-001...
Page 61
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol No. Part No. Part Name Description Local LV35643-001A EARTH PLATE VKZ4777-006 MINI SCREW (x6) QYSPSPU1730MA SCREW M1.7 x 3mm QLE0038-001 OEL MODULE LV43889-001A SW PWB SHEET LV40847-020A SPACER(H) (x2) LV40848-055A SPACER(P) LV36077-001A NAME PLATE AR7500 LV36076-001A...
Page 62
http://www.xiaoyu163.com 3 7 63 1515 0 CD mechanism assembly and parts list Block No. Grease FMU-JC3-2D = JVS-1003 = MOBIL-1 = JVG-31N = JC-803B 61 38 L 13942296513 11.10mm 0.10mm 82 82 Inside 1.2 0.1mm u163 After set pick up apply grease The parts without symbol number are not service.
Page 63
http://www.xiaoyu163.com 3 7 63 1515 0 CD mechanism Block No. [M]B][M][M] Symbol No. Part No. Part Name Description Local VKZ4539-056 MINI SCREW (x5) LV10857-002A CHASSIS FRAME 2 LV30225-0J6A SPACER (x2) LV35272-001A DAMPER(F) (x2) LV35273-001A DAMPER(R) QYSPSTU2045MA TAP SCREW M2 x 4.5mm(x3) LV43039-001A DAMPER SP.(R) LV43849-001A...
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol No. Part No. Part Name Description Local LV43011-001A THRUST SPRING QYSPSFT2040ZA TAP SCREW M2 x 4mm LV21604-004A L.S.HOLDER 1 VKZ4539-056 MINI SCREW (x2) LV34582-002A L.S.HOLDER 2 VKZ4539-056 MINI SCREW (x2) LV34581-002A SUB GUIDE VKZ4539-056 MINI SCREW (x3)
http://www.xiaoyu163.com 3 7 63 1515 0 Electrical parts list Main board Symbol No. Part No. Part Name Description Local Block No. [0][1] D711 MA8056/M/-X Z DIODE Symbol No. Part No. Part Name Description Local D712 MA8056/M/-X Z DIODE D713 MA8056/M/-X Z DIODE...
Page 66
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local NDC31HJ-101X C CAPACITOR 100pF 50V J C973 NCB31CK-104X C CAPACITOR 0.1uF 16V K NDC31HJ-101X C CAPACITOR 100pF 50V J C974 NCB31CK-104X...
Page 67
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local C2700 QTE1C55-226Z E CAPACITOR 22uF 16V C2701 QEKJ1CM-226Z E CAPACITOR 22uF 16V M NRSA63J-102X MG RESISTOR 1kΩ...
Page 68
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local R742 NRSA63J-102X MG RESISTOR 1kΩ 1/16W J R952 NRSA63J-273X MG RESISTOR 27kΩ 1/16W J R743 NRSA63J-102X MG RESISTOR 1kΩ...
Page 69
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local R2503 NRSA63J-682X MG RESISTOR 6.8kΩ 1/16W J R4103 NRSA63J-102X MG RESISTOR 1kΩ 1/16W J R2504 NRSA63J-103X MG RESISTOR 10kΩ...
Page 70
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local CN351 QNZ0095-001 CONNECTOR C461 NBE20JM-106X TA E CAPACITOR 10uF 6.3V M CN381 QGA2501C1-03 CONNECTOR W-B (1-3) C471 NDC31HJ-471X C CAPACITOR...
Page 71
http://www.xiaoyu163.com 3 7 63 1515 0 Mechanism control board Symbol No. Part No. Part Name Description Local Block No. [0][3] R815 NRSA63J-102X MG RESISTOR 1kΩ 1/16W J R816 NRSA63J-102X MG RESISTOR 1kΩ 1/16W J Symbol No. Part No. Part Name Description Local...
Page 72
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local C630 NCB31EK-333X C CAPACITOR 0.033uF 25V K R514 NRSA63J-473X MG RESISTOR 47kΩ 1/16W J C631 NCS31HJ-471X C CAPACITOR 470pF 50V J R515...
Page 73
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local R606 NRSA63J-220X MG RESISTOR 22Ω 1/16W J R609 NRSA63J-473X MG RESISTOR 47kΩ 1/16W J CN502 QGF0501F1-08X CONNECTOR FFC/FPC (1-8) R611...
Page 74
Packing materials and accessories parts list Block No. No additional / supplemental order of WARRANTY CARDs are available. A7 A8 A3 A4 A3 A4 A5 A6 A5 A6 KD-SHX750 KD-AR7500 L 13942296513 KIT: A9 A10 A12 A13 KD-AR7500 only u163 3-18 http://www.xiaoyu163.com...
Page 75
http://www.xiaoyu163.com 3 7 63 1515 0 Packing and Accessories Block No. [M][3][M][M] Symbol No. Part No. Part Name Description Local LVT1310-001A INST BOOK ENG SPA FRE LVT1310-002A INSTALL MANUAL LVT0717-001B TROUBLE SHEET(C ------------ WARRANTY CARD BT-51029-2 AR7500 ------------ WARRANTY CARD BT-51018-4 SHX750 BT-51034-2...