Zephyr Brisas BMI-E36AG Use, Care And Installation Manual
Hide thumbs
Also See for Brisas BMI-E36AG:
- Use, care and installation manual (21 pages) ,
- Use, care and installation manual (21 pages)
Related Manuals for Zephyr Brisas BMI-E36AG
Summary of Contents for Zephyr Brisas BMI-E36AG
- Page 1 Brisas BMI-E36AG BMI-E36AS BSI-E36AS BVE-E30AS BVE-E36AS Model number: Serial Number: SEP08.0101 © Zephyr Corporation...
- Page 3 SAFETY NOTICE ..............LIST OF MATERIALS ............INSTALLATION Ducting Calculation Sheet ........Mounting Height & Clearance ........ Ducting Options ............Hood Speci cations 8-10 ........... Mounting the Hood BMI & BSI ......Mounting the Hood BVE......... 12 Ductless Recirculating ..........FEATURES &...
- Page 4 READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE. WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: a.
-
Page 5: Operation
WARNING TO REDUCETHE RISK OF FIRE, USE ONLY METAL DUCTWORK. CAUTION T o reduce risk of fire and to properly exhaust air outside - Do not vent exhaust air into spaces within walls, ceilings, attics, crawl spaces or garages. OPERATION Always leave safety grilles and filters in place. -
Page 6: Hardware Package Contents
MODELS: BMI-E30AS BMI-E30AG BSI-E30AG BVE-E30AS BVE-E36AS PARTS SUPPLIED 1 - Hood with internal blower 1 - Duct cover wall bracket 1 - Duct cover assembly (top and bottom) 1 - Hardware package 1 - 6” round backdraft damper (pre-installed) 2 - 50W GU-10 halogen light bulbs 2 - Metal mesh filters 1 - Canopy, glass or stainless steel (for BMI and BSI models only) HARDWARE PACKAGE CONTENTS... - Page 7 Equivalent number Equivalent number Duct pieces Duct pieces length x used T otal length x used T otal 3-1/ 4” x 10” 1 Ft. 6”- 8” Round 30 Ft. Rect., wall cap straight with damper 7” Round, 1 Ft. 6”- 8” Round, 30 Ft.
-
Page 8: Damage - Shipment/Installation
Minimum mount height between range top to hood bottom should be no less than 24”. Maximum mount height should be no higher than * Min. ducted (A) 32”. Min. recirc. (B) Max. It is important to install the hood at the proper mounting height. - Page 9 WARNING FIRE HAZARD NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside, unless using the recirculating option. Use single wall rigid Metal ductwork only. Fasten all connections with sheet metal screws and tape all joints w/ certified Silver Tape or Duct Tape.
- Page 11 8 " 8 " 16 " 16 " 4 " 16 " 8 "...
- Page 13 CAUTION: At least two installers are required due to the weight and size of the hood. 1. Measure from range top to hood bottom and mark line A. (24” minimum from range top) . 2. Plum and mark center line. 3.
- Page 14 CAUTION: At least two installers are required due to the weight and size of the hood. 1. Measure from range top to hood bottom and mark line A. Duct Cover Bracket (24” minimum from range top) . 2. Plum and mark center line. 4"...
- Page 15 Charcoal Filter Replacements Hood Model Part No. Qty to Order All Brisas Models Z0F-C002 DO NOT WASH CHARCOAL FILTERS. Charcoal filters may need to be changed more often depending on cooking habits. Charcoal Filter Dimensions: 9in x 6-3/8in...
-
Page 17: Surface Maintenance
SURFACE MAINTENANCE: Clean periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent , or steel wool/scouring pads which will scratch and damage surface. For heavier soil use liquid degreaser. After cleaning it is recommended that you use non-abrasive stainless steel polish/cleaners, to polish and buff out the stainless luster and grain. -
Page 18: Replacing Light Bulbs
REPLACING LIGHT BULBS CAUTION: Light bulb becomes extremely hot when turned on. DO NOT touch bulb until switched off and cooled. Touching hot bulbs could cause serious burns. Make sure all power is turned off and bulbs are not hot. Remove by turning bulb counter clockwise. - Page 19 TROUBLESHOOTING PROCEDURES FOR BRISAS Issue Cause What to do After installation, 1. The power source is not turned ON. 1. Make sure the circuit breaker and the unit’s the unit doesn’t power is ON. work. 2. The power line and the cable locking connector 2.
- Page 20 DESCRIPTION PART# Replacement Parts Light Bulb GU-10 50W (each) Z0B-0020S Optional Accessories Recirculating Kit BRC-0002 (for BMI & BSI) BRC-0001 (for BVE) Replacement Charcoal Filter Z0F-C002 Duct Cover Extension B1C-00MI (for BMI & BSI) B1C-00VE (for BVE)
Need help?
Do you have a question about the Brisas BMI-E36AG and is the answer not in the manual?
Questions and answers