CONTENTS MAIN FEATURES PRODUCT SAFETY AND HEALTH STATEMENTS PACKAGE CONTENTS DESCRIPTION OF TRANSMITTER PARTS BUTTON FUNCTION DESCRIPTION OF COLLAR/RECEIVER PARTS BATTERY CHARGER TESTING YOUR COLLAR FITTING THE COLLAR ON THE DOG CHARGING THE BATTERIES RECEPTION METAL BELT CLIP ACCESSORIES ACCESSORIES BASIC MAINTENANCE TROUBLE SHOOTING GUIDE WARRANTY AND REPAIR...
PRODUCT SAFETY AND HEALTH STATEMENTS MAIN FEATURES Easy-to-use, ergonomic transmitter. Proper e-collar use Dogtra e-collars are intended for the sole purpose Rheostat dial allows for gradual increases in of behavior modification of dogs. They are not stimulation intensity with no jumps between intended for human use or use on other animals.
PACKAGE CONTENTS DESCRIPTION OF TRANSMITTER PARTS DESCRIPTION OF PACKAGE CONTENTS TRANSMITTER PARTS Transmitter transmitter (1-dog) Receiver (two collar receivers for Dotra two-dog models) Battery charger and splitter cable Antenna Test light Rheostat Intensity Dial Owner’s manual Carrying case Indicator Light (LED Window) ON/OFF Metal belt clip accessory...
Page 5
DESCRIPTION OF TRANSMITTER PARTS DESCRIPTION OF TRANSMITTER PARTS DESCRIPTION OF TRANSMITTER PARTS transmitter (2-dog) Antenna Nick/Constant Rheostat Toggle Switch Intensity Dial Transmitter Antenna Indicator Light A short 2 antenna is supplied with the ON/OFF (LED Window) Switch transmitter. -dog -dog The antenna must be fastened to the Nick &Constant Pager...
Page 6
DESCRIPTION OF TRANSMITTER PARTS DESCRIPTION OF TRANSMITTER PARTS LCD Screen Rheostat Intensity Dial The LCD screen indicates the stimulation The Rheostat Intensity Dial is located on level (0-127) on the screen. the top of the transmitter: (0) being the lowest level and (127) being the highest.
Page 7
DESCRIPTION OF TRANSMITTER PARTS DESCRIPTION OF TRANSMITTER PARTS Care for LCD Transmitters in Cold Temperature In cold temperatures (10 degrees F or below), the Liquid Crystal Display (LCD) on your transmitter may be dim or slow to respond. Wait until the display becomes visible before selecting any training level.
BUTTON FUNCTION DESCRIPTION OF TRANSMITTER PARTS BUTTON FUNCTION (1-dog) Pager Nick ON/OFF Constant Transmitter Battery Charging Receptacle & Switch Rubber Plug Located on the backside of the transmitter, The transmitter for the the charging receptacle is covered by a rubber single dog unit has four buttons (one on the plug.
Page 9
BUTTON FUNCTION BUTTON FUNCTION “Constant” Button (2-dog) The “Constant” button is located on the bottom left. Pressing the “Constant” button Nick/Cont. gives continuous stimulation as long as the Toggle Switch button is pushed, for up to 12 seconds. If the -dog ON/OFF Nick &...
BUTTON FUNCTION DESCRIPTION OF COLLAR / RECEIVER PARTS When either the orange or gray stimulation DESCRIPTION OF button is pressed and the toggle is set on COLLAR / RECEIVER PARTS “Nick” the receiver emits a single, rapid pulse of electrical stimulation. When you press either the orange or gray stimulation button, and the toggle is set on “Constant”, the receiver emits a continuous...
Page 11
Internal Antenna (Green = full charge, Amber = medium All Dogtra E-collars have non-exposed charge, Red = needs charge) antennas that are located inside the When the Constant button on the collar/receiver.
NOTE : Only use Dogtra-approved Chargers for your Dogtra e-collar. This will prevent 2. Place the test light included in the package any damage that can be incurred from contents on the contact points as shown in attempting to use a different charger.
TESTING FITTING THE COLLAR ON THE DOG 3. Turn the transmitter on by pressing the blue FITTING THE COLLAR ON THE DOG button on the right side of the transmitter until the LCD screen illuminates. The LCD screen shows the amount of battery life remaining and the LED blinks once every 2 seconds.
Page 14
Also, as the dog’s Dogtra uses surgical stainless steel contact attitude changes, especially during times of points and anti-microbial plastic to protect the increased excitement or distraction, you may dog’s skin.
CHARGING THE BATTERIES CHARGING THE BATTERIES CHARGING THE BATTERIES Recharge the unit if : The LED indicator light on the collar receiver is emitting a red color. If the 3 bar indicator on the transmitter LCD shows just 1 bar. The indicator light on the transmitter or receiver will not come on.
CHARGING THE BATTERIES RECEPTION RECEPTION 3. After charging, cover the battery charging receptacles with the rubber plugs on the transmitter and receiver. collar has a range of 1/2-mile. Depending on the 4. The battery is fully charged with a 10-hour way you use your transmitter, the range may charge.
(888) 811-9111. You may also browse the The final result should look like step 2. selection at shop.dogtra.com. European Charger Designed for use with 230V AC electrical outlets in Europe.
If you suspect your unit is malfunctioning please refer to the “Troubleshooting Guide” before you send your unit in for service. If you have any questions or concerns, you may direct your inquiries to info@dogtra.com or call (888) 811-9111.
Page 19
- The antenna(s) may be damaged. To order - For Dogtra units over two years old from the parts, please contact Customer Service at purchase date, the batteries may be replaced.
If your product is not registered and a proof Dogtra reserves the right to retain and discard any parts or accessories that of purchase is not available at the time of service, Dogtra will estimate the...
Page 21
Dogtra is not responsible for units damaged or lost in transition to Dogtra. Dogtra is not responsible for loss of training time or inconvenience while the unit is in for repair work. Dogtra does not provide loaner units or any form of compensation during the repair period.
Need help?
Do you have a question about the 1900NCP Field Star Series and is the answer not in the manual?
Questions and answers