Page 1
Manuel d’utilisation Lire attentivement et bien assimiler le manuel d’utilisation avant d’utiliser la machine. WS 462 Manual de instrucciones Lea detenidamente el manual de instrucciones y asegúrese de entender su contenido antes de utilizar la máquina.
KEY TO SYMBOLS Symbols on the machine: Symbols in the operator’s manual: WARNING! The machine can be a Inspection and/or maintenance should be dangerous tool if used incorrectly or carried out with the motor switched off and carelessly, which can cause serious or the plug disconnected.
Personal protective equipment ........General safety precautions .......... General working instructions ........Basic working techniques ..........PRESENTATION WS 462 ................ ASSEMBLY Mount wall mountings and rail ........Mount the saw carriage and saw ......... Fit the blade ..............Flush cutting ..............
WHAT IS WHAT? What is what on the wall saw? 1 Saw carriage 7 Track 2 Locking handle 8 Blade flange hub 3 Saw unit 9 Outer blade flange 4 Speed valve 10 Hydraulic hose connections 5 Cutting arm 11 Water connector 6 Blade guard guide 4 –...
Lead from lead-based paints. • This machine is only intended for use together with a Crystalline silica from bricks, cement and Husqvarna PP 345 and Husqvarna RC 348. All other use other masonry products. is forbidden. Arsenic and chromium from •...
SAFETY INSTRUCTIONS Personal protective equipment General safety precautions Do not use the machine without first reading and WARNING! You must use approved personal understanding the contents of this Operator’s Manual. protective equipment whenever you use the machine. Personal protective equipment WARNING! There is always a risk of crush cannot eliminate the risk of injury but it will injuries when working with products...
• Never use blades other than original blades designed for • Check that electrical cables within the working area are the machine. Check with your Husqvarna dealer to see not live. which blades are best suited for your usage. •...
SAFETY INSTRUCTIONS Basic working techniques • Always start by cutting a pilot cut. This is done by feeding the blade 3-7 cm (1,2”-2,8”). Now make the pilot cut. The cut should not be made at maximum speed, but with care in order to obtain a straight cut and with that a basis for the next cut.
WS 462 To utilises the input effect in the best possible way the saw is mounted on Husqvarna’ the latest rail. This is a very stable rail, which allows the saw to be controlled more precisely, which in turn results in more efficient cutting. As the equipment’s component parts work with small losses and as...
89 mm (3.5"). Tighten the There are two types of wall mounting available for the expander bolts. Husqvarna WS 400 series. One, the standard wall mounting, which is supplied on delivery, and secondly the universal swivel wall mounting.
However, it is not sufficiently secured On the Husqvarna WS 400-series the blade is fitted in an to begin cutting. entirely new way. The new mounting permits, in addition to the...
ASSEMBLY Flush cutting 4 Hang the blade with the blade flange and blade flange hub fitted on the cutting arm (blade is not shown in the figure). Screw off the outer blade flange and mount the blade on the blade flange hub. •...
Connect the hydraulic unit IMPORTANT! This machine is only intended for use together with a Husqvarna PP 345 and Husqvarna RC 348. All other use is forbidden. 2 Make sure that the pivot arm is positioned vertically. Lift Please read the operator´s manual supplied with the...
STARTING AND STOPPING Before starting Cleaning • Enclose the area to be cut so that unauthorised persons The saw should be cleaned once cutting is finished. It is can not be injured or disturb the operator. important to clean all the saw equipment. It is a good idea to disconnect the water hose from the pivot arm and use this to •...
SETTINGS AND ADJUSTMENTS Adjusting the guide wheels Adjust the saw carriage In order for the saw to run stably and saw a straight cut, the As the saw wears, after a number of hours working, it can be four guide wheels must rest against the rail and not have too a good idea to ensure that the saw sits firmly in the saw much play.
Replace the blade or the blade guard if it is exposed to impact or is cracked. The cutting arm contains 1 dl of Husqvarna Oil 150, a transmission oil of the type EP 150. The oil should be replaced for the first time in connection with the first service.
EQUIPMENT Equipment manufactured by Husqvarna is warranted to be free from manufacturing defects in normal service for a period of two (2) years from date of purchase by the original consumer purchaser. Component manufacturers offer separate warranty periods.