Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Leica Disto Special5
Summary of Contents for Leica Disto Special5
- Page 1 THE ORIGINAL LASER DISTANCEMETER...
-
Page 2: Table Of Contents
Message Codes ............18 Warranty in practice as they enabled the product to be used in a Leica Geosystems AG offers its customers a two (2) year DISTO special hand-held laser meter technically correct and efficient manner. warranty on DISTO instruments. For more information, Congratulations on your purchase of a DISTO™. -
Page 3: Keypad
Tracking Information Multiply [ x ]/ Timer 14 min. / max. Tracking Display of the mathematical signs/operations Release Main display (e.g. measured distance) Plus [ + ] 15 Mermory, Stack Distance measurement Menu Tracking Keypad Leica DISTO™ special 1.0.0 en... -
Page 4: How To Use The Instrument
Illumination is switched on/off with a key press. Illumination switches off after 30 seconds if no key is pressed. D5-Z3 Remove battery cover. Replace batteries. Appears on the display if battery voltage is too low. How to Use the Instrument Leica DISTO™ special 1.0.0 en... -
Page 5: Distance Measurement
At the back of the instrument is a 1/4" camera thread for the stand. Changes are lost when instrument is switched D5-Z5 off. For stable measuring turn bumper 90°. Basic setting: rear reference D5-Z7 How to Use the Instrument Leica DISTO™ special 1.0.0 en... - Page 6 The side to be measured blinks. After the last "beep", the measurement is made and the value displayed. Make 2 measurements (l x w). The result and the two partial results appear on the display. How to Use the Instrument Leica DISTO™ special 1.0.0 en...
- Page 7 DISTO™ to offset 0.000: Call up function as key [+ / -] switch between the various menu described points. Press. Confirm selection, activate menu point. Confirm function. D5-Z10 How to Use the Instrument Leica DISTO™ special 1.0.0 en...
-
Page 8: Functions
The adjustment is for m, m² and m³ rsp. ft, ft² and Confirm; value is ready to be used for (e.g. ft³ only. calculating an area). Confirm. and a number (=memory location) starts to blink. With key [+ / -] select memory location (1-10). Functions Leica DISTO™ special 1.0.0 en... - Page 9 Move the DISTO™ a large amount around the target point. Move the DISTO™ a large amount around the target point. Activate continuous measurement with a brief Stop continuous measurement. press. Functions Leica DISTO™ special 1.0.0 en...
- Page 10 DISTO™ on a camera tripod. In this case the axis of the laser beam is approx. 70 to 100mm above the centre of rotation - this can lead to signi- D5-Z13 ficant variations in the height. Functions Leica DISTO™ special 1.0.0 en...
- Page 11 "2 ---" starts blinking. Aim at the upper point (1). Point the DISTO™ approximately horizontal (2). Trigger measurement; do not move the Press, a continuous measurement is triggered. instrument! Functions Leica DISTO™ special 1.0.0 en...
-
Page 12: User Information
Trigger measurement; do not move the colorless liquids (e.g. water) or (dust free) glass, styropor. instrument! or similar semi- permeable surfaces. For materials and Value is accepted. liquids unfamiliar to you always take a trial measurement. User Information Leica DISTO™ special 1.0.0 en... -
Page 13: Safety Instructions
• Use of accessories from other manufacturers without The DISTO™ may receive a signal that is too weak the express approval of Leica Geosystems. The person responsible for the instrument must ensure (error message 255). that all users understand these directions and adhere to •... -
Page 14: Limits Of Use
They are also responsible for the effectiviness of these Limits of use Hazards in use safety concepts in combination with the Leica Geosystems equipment. See section “Technical Data“ Important hazards in use Responsibilities of the person in charge of the... - Page 15 (e.g. safety limit switch), it is assured that no damage will occur. Safety Instructions Leica DISTO™ special 1.0.0 en...
-
Page 16: Laser Classification
Although the DISTO™ meets the strict regulations and dangerous when you aim at areas that reflect like a mirror, Health and Human Service, Code of Federal standards which are in force in this respect, Leica or emit reflections unexpectedly (e.g. a mirror, metallic Regulations) Geosystems cannot completely exclude the possibility that surfaces, windows, prisms, liquids). - Page 17 Changes or modifications not expressly approved comply with the limits for a Class B digital device, pursuant by Leica Geosystems for compliance could void the user’s to part 15 of the FCC Rules. These limits are designed to authority to operate the equipment.
- Page 18 Laser beam outlet Max. radiant power * 0.95 mW* Measurement uncertainty ±5% Max. radiant power per pulse 8 mW CAUTION: Allow only authorized Leica Geosystems service D5-Z15 workshops to service the instruments. D5-Z16 D5-Z17 Safety Instructions Leica DISTO™ special 1.0.0 en...
-
Page 19: Technical Data
(-13°F to +158°F) Laser beam interrupted Repeat measurement All illustrations, descriptions and technical specifica- Operating -10°C to +50°C All other messages Call service "System" (-14°F to +122°F) tions are subject to change without prior notice. Technical Data Leica DISTO™ special 1.0.0 en... - Page 20 International Standards of Quality Management and Quality Systems (ISO standard 9001) Ask your local Leica Geosystems agent for more and Environmental Management Systems (ISO standard information about our TQM program. 14001).
Need help?
Do you have a question about the Disto Special5 and is the answer not in the manual?
Questions and answers