Related Manuals for DCA Intertel JP 215
Summary of Contents for DCA Intertel JP 215
- Page 1 Technical Manual JP 215 Rugged Thermal Printer DCA Intertel BV Distributieweg 25, 2404 CM Alphen a/d Rijn The Nederlands Phone: +31(0)172 604963 Fax: +31(0)172 605237 website: www.dca-group.com Intertel Intertel...
-
Page 2: Table Of Contents
TABLE OF CONTENS 1. General Specification 9. Appendix 9.1 Appendix A 2. External Dimensions 9.2 Appendix B 9.2.1 Test on Power Cable 3. Design And Operation 9.2.2 Test on Data Cable 3.1 Front View 9.3 Appendix C 3.2 Procedure to Replace Paper Roll 9.4 Appendix D 9.5 Appendix E 4. -
Page 3: General Specification
1. General Specification 2. External Dimensions Connector Unit : mm ITEM SPECIFICATION Dimensions 178(W) x 50 (H) x 162 (D) mm 1 DIN Power Cord Weight Approx. 1.70 kg Paper Insertion Drawing type (See 4. DESIGN AND OPERATION) Power 4-M5 Requirements Set Screw Character mode... -
Page 4: Design And Operation
3. Design And Operation 4. Block Diagram 3.1 Front View Error Lamp (RED) Power Lamp (Green) Power Voltage Head up ON/Off Switch Paper Error Power Switch Regulator 1 Empty Switch Feed On/Off Eject Eject Switch Feed (Paper End) CN10 If the “error light” is flashing, some of the following conditions may exist: DC 10~16V 1. -
Page 5: Interface Specification
5. Interface Specification 5.5 Connector 1. Part Name : DIN Connector (8 pin) 5.1 Signal condition (Comply with EIA RS 232-C) 2. Part Number : TCS2380-01-1011 3. DIN Standard No. :45326 CONDITION SIGNAL LEVEL 4. Manufacturer : Hosiden Electronics Co. Ltd. ITEM High Binary State... -
Page 6: Power Supply Cord
6. Power Supply Cord 7.1 Character Code and Control Code 7.1.1 THE CHARACTERS HIGH 0000 0001 0010 0011 0100 0101 0110 0111 Polarity + Mark. 0000 0001 Error Power 0010 “ Eject Feed On/Off 0011 0100 0101 0110 & 0111 ‘... -
Page 7: Bit Image Graphics
7.3 Bit Image Graphics (1) 7.4 Bit Image Graphics (2) 1.640 dots/line graphics 1.248 dots/line graphics 2.Command “ESC” “V”(N1) (N2) 2.Commands “ESC” “K” (N1) (N2) 3.Hexadecimal Data <1B><5G><n1><n2> 3.Hexadecimal Data <1B><4B><n1><n2> 4.Function 4.Function This is a four byte command which sets up the bit image graphics mode. The two This is a four bytes command which sets up the bit image graphic mode. -
Page 8: Control Code
7.5 Control Code 7.5.7 DC3 1.Device Control 3 Command 7.5.1 LF 2.Hexadecimal Data <13> H 1.Line Feed Command 3.Function 2.Hexadecimal Data <DA> H When the printer buffer is stored more than three quarters, the printer sends com- 3.Function mand DC3 to the host. After the host receives command DC3, the host may not send If characters are stored in the printer line-buffer when command LF is received, they data to the printer. -
Page 9: Environmental Specifications
8. Environmental Specifications (Without transport package) ENVIRONMENTAL SPECIFICATIONS TEST ITEMS AND TEST CONDITIONS ENVIRONMENTAL SPECIFICATIONS TEST ITEMS AND TEST CONDITIONS 1. Temperature Operating Low Tempera- -20°C 4. life (without 5 years (7000m) Life Test Normal Temperature Humidity ture operating Host Print: 350cycles (See thermal head and Humidity Self Print Appendix A) - Page 10 9. Appendix 9.2 Appendix B 9.1 Appendix A Radiation Noise Test 9.2.1 Test on Power Cable Low Temperature Operating Test Testing Method The character (code <7F>H) is continuously printed. 0.2m Freezer (Operating Temperatre:-20°C DC Power Printer Host Supply Power Cable -20°C Current Probe...
- Page 11 9.3 Appendix C 9.5 Appendix E Electrostatic Discharge Test Thermal paper specification S P E C I F I C A T I O N J U J O T H E R M A L G R A D E C O D E : T F 5 0 K S - E 4 5 CHARACTERISTICS UNIT...
- Page 12 DYNAMIC COLOR DERVEROPMENT STATIC COLOR DERVEROPMENT S.W.T Thin Film TYPE 0.6w/d. mj/dot. Temp. °C Intertel Intertel Intertel Intertel...
Need help?
Do you have a question about the JP 215 and is the answer not in the manual?
Questions and answers