Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Hangar 9 Taylorcraft 26cc Hangar 9
Summary of Contents for Hangar 9 Taylorcraft 26cc Hangar 9
- Page 1 Taylorcraft 26cc BNF Assembly Manual ®...
-
Page 2: Table Of Contents
Table of Contents Introduction Notice Intro ..................2 The Hangar 9 Taylorcraft 26cc BNF is a gorgeous giant-scale ® All instructions, warranties and other collateral Product Support ...............2 recreation of a one-of-a-kind clipped-wing T-Craft that you documents are subject to change at the sole discretion Specifications ..............2... -
Page 3: Included Parts Listing
(4)*, strut to wing bracket (4) Evolution ® 16 x 6 propeller propeller 4-40 lock nut jury strut brace (4)*, strut to wing *preinstalled items bracket (4) #4 black flat washer jury strut brace* Hangar 9 Taylorcraft 26cc BNF... -
Page 4: Contents Of Kit And Parts Listing
HAN4908 Landing Gear* HAN4566 Pilot HAN4902 Top Window HAN4915 Seat and Mounting Panel ZENE26A G26 Air Engine (1.55 cu in) *Items are not preassembled and do not include electronics EVO16060 Evolution Propeller, 16 x 6 Hangar 9 Taylorcraft 26cc BNF... -
Page 5: Important Information Regarding Warranty
Zenoah Ignition Kill Switch ZEN20000 etc. Remember to take your time and follow the directions. Hangar 9 Aluminum CNC 2 -inch Spinner HAN4902015 Hangar 9 Fuel Filler with Overflow Fitting HAN116 Evolution 16 x 6 Propeller EVO16060 ® Hangar 9 Taylorcraft 26cc BNF... -
Page 6: Charging The Receiver Battery
2–3 times prior to flying. 2. Follow the procedure as described in your radio manual for binding the receiver and transmitter. Check the operation of the rudder, elevator and throttle servos using the radio system. Hangar 9 Taylorcraft 26cc BNF... -
Page 7: Landing Gear Installation
A machined hex wrench is helpful to allow the bolts to be tightened and not strip the head of the bolt. Note: Always use threadlock on metal-to-metal fasteners to prevent them from vibrating loose. Hangar 9 Taylorcraft 26cc BNF... -
Page 8: Tail Installation
If any loose hinges are found, apply thin CA to both sides of the hinge. Allow the CA to soak into the hinge before checking them again. Hangar 9 Taylorcraft 26cc BNF... -
Page 9: Tail Wheel Installation
A machined hex wrench is helpful to allow the bolts to be tightened and not strip the head of the bolt. Hangar 9 Taylorcraft 26cc BNF... - Page 10 Phillips screwdriver to make the holes for the two mounting the rudder. 7. Place 2–3 drops of thin CA in each hole to harden the screws in the bottom of the rudder. surrounding wood. This will keep the screws from vibrating loose in flight. Hangar 9 Taylorcraft 26cc BNF...
-
Page 11: Tail Bracing Installation
The fuselage assembly will also be required for this section end of the spring with needle nose pliers. Use care when bending the springs so the tail wheel is aligned with the of the manual. rudder. Cut the excess spring using side cutters. Hangar 9 Taylorcraft 26cc BNF... - Page 12 Leave the screw finger-tight at this time. 5. Repeat steps 3 and 4 to install the remaining 10 -inch (273mm) strut. Be careful to not induce any warps in the stabilizer when installing the braces. Hangar 9 Taylorcraft 26cc BNF...
- Page 13 9. Repeat steps 6 through 8 to install the remaining short strut. Again leave the hardware loose at this time. Note: Always use threadlock on metal-to-metal fasteners to prevent them from vibrating loose. Hangar 9 Taylorcraft 26cc BNF...
-
Page 14: Engine Installation
Note: Always use threadlock on metal-to-metal 3. Use side cutters to cut the tie-wrap holding the ignition has been tightened. fasteners to prevent them from vibrating loose. ground leads and fuel tubing together. Hangar 9 Taylorcraft 26cc BNF... - Page 15 If you heat hardware to secure the muffler to the engine. up the engine and then tighten the bolts down when hot, the bolts will stay secure longer. Hangar 9 Taylorcraft 26cc BNF...
-
Page 16: Cowling, Propeller And Spinner Installation
It may be necessary to change the travel adjust at the radio to prevent the servo from binding at high- and low-throttle. Make sure when the throttle is at idle the butterfly in the carburetor is closed. Hangar 9 Taylorcraft 26cc BNF... - Page 17 G26 is not being used as the carburetor is completely enclosed inside the cowling. hint: A small dot of canopy glue on the threads of the screws will help to stop them from coming loose from vibration. Hangar 9 Taylorcraft 26cc BNF...
-
Page 18: Rudder And Elevator Linkages
Tighten the 4-40 nut against the clevis to prevent it from changing positions in flight. Channel number Channel Name Position Throttle Normal Right Aileron Normal Right Elevator Reverse Rudder Reverse Left Aileron Normal Left Elevator Reverse Hangar 9 Taylorcraft 26cc BNF... -
Page 19: Interior Installation
2. Use a #1 Phillips screwdriver to install and remove one of the 2mm x 10mm washer head wood screws in each of the four mounting holes in the fuselage. This will cut threads in the surrounding wood, preparing them for the next step. Hangar 9 Taylorcraft 26cc BNF... -
Page 20: Wing Strut Installation
Use a 5/64-inch hex wrench will straddle the fuel tank when installed. Use hook and loop and 1/4-inch nut driver to tighten the hardware. tape or silicone adhesive to secure the pilot in the seat. Hangar 9 Taylorcraft 26cc BNF... -
Page 21: Wing Installation
Adjust the position of the strut end so the hole in the end aligns with the hole in the bracket. Once adjusted, tighten the nut against the end to prevent the end from vibrating and changing position. Hangar 9 Taylorcraft 26cc BNF... -
Page 22: Center Of Gravity
Center both ailerons at this time. Tighten the 4-40 nut against the clevis to prevent it from changing positions in flight. Hangar 9 Taylorcraft 26cc BNF... -
Page 23: Control Throws
Subsequent charges may be performed with peak detecting chargers, and at higher rates. Do Not exceed the lower of 1C, or 2000mA. (Example: 1650mAH battery, 1C = 1.65A or 1650mA charge rate) Hangar 9 Taylorcraft 26cc BNF... -
Page 24: Preflight
7 . All servo pigtails and switch harness plugs should be in the manual, prior to assembly, setup or use, in order to secured in the receiver. Make sure the switch harness operate correctly and avoid damage or serious injury. moves freely in both directions. Hangar 9 Taylorcraft 26cc BNF... -
Page 25: Introduction
• Always run your model engine in a well-ventilated • Always keep your fuel in a safe place well away from area. Model engines produce possibly harmful carbon sparks, heat or anything that can ignite. monoxide fumes. • Always ensure the aircraft is secure and will not move once the engine is started. Hangar 9 Taylorcraft 26cc BNF... -
Page 26: Engine Operation
3. Make sure the fuel tank line(s) is properly connected. Idle Screw The main line should be connected to the carburetor spray bar. 4. Be certain the mufflers are installed properly. 5. Fill the fuel tank. Hangar 9 Taylorcraft 26cc BNF... -
Page 27: Engine Care And Maintainence
Remove the rotor (flywheel). If it cannot be detached, nose down in order to keep oil in the bearings. use a plastic hammer and tap the part lightly. Hangar 9 Taylorcraft 26cc BNF... -
Page 28: Maintenance Chart
Check/Cleaning Bearings Check/Cleaning Crankshaft Check/Alignment Rotor Check Propeller Hub (PU) Check/Alignment Water Jacket (PUM) Check/Leakage Hangar 9 Taylorcraft 26cc BNF... -
Page 29: Troubleshooting Guide For Gasoline Engines
Replace The spark plug heat range is not proper Fuel Consumption d) The engine does not stop Weight 1.69 (* 1.52) Overheating See c) The Stop switch is defective Repair Switch wiring is disconnected Repair Hangar 9 Taylorcraft 26cc BNF... -
Page 30: Exploded Illustration
ZEN2361 WASHER ZEN335053410 ZEN2362 NUT, M8 ZEN114013141 ZEN23156 GASKET, MUFFLER 54-1 ZEN0125230550 ZEN2357 BOLT, M5 x 50 55-1 ZEN026330408 ZEN2358 SCREW, M4 x 8 56-1 ZENT207515110 ZEN2655 MUFFLER ZENT303991310 ZEN23124RC SOCKET ZEN20005 ZEN20005 PISTON STOPPER Hangar 9 Taylorcraft 26cc BNF... -
Page 31: Warranty Services
61822 USA your product for repair. When calling Horizon, you will be asked productsupport@horizonhobby.com to provide your complete name, street address, email address and 877-504-0233 phone number where you can be reached during business hours. Hangar 9 Taylorcraft 26cc BNF... -
Page 32: Airframe Warranty And Repair Policy
61822 USA your product for repair. When calling Horizon, you will be asked productsupport@horizonhobby.com to provide your complete name, street address, email address and 877-504-0233 phone number where you can be reached during business hours. Hangar 9 Taylorcraft 26cc BNF... -
Page 33: Compliance Information For The European Union
GERMANy D-25337 Elmshorn Horizon Technischer Service Equipment class: Hamburger Str. 10 erklärt das Produkt: HAN Taylorcraft 26cc BNF HAN4920 25335 Elmshorn declares the product: Germany The object of declaration described above is in conformity with Artikelnummer(n): HAN Taylorcraft 26cc BNF HAN4920 service@horizonhobby.de... -
Page 34: Academy Of Model Aeronautics National Model Aircraft Safety Code
(AMA Documents #922- Testing for RF Interference; safe operation of your model aircraft. #923- Frequency Management Agreement) Hangar 9 Taylorcraft 26cc BNF... -
Page 35: Engine Warranty Information
Engine Type: __________________________________________________________________________________ Date of Purchase: ______________________________________________________________________________ Owner’s Name: ________________________________________________________________________________ Street Address: ________________________________________________________________________________ City/State/Zip: _________________________________________________________________________________ Daytime Phone Number: _________________________________________________________________________ Purchased From: _______________________________________________________________________________ Dealer’s Name: ________________________________________________________________________________ Street Address: ________________________________________________________________________________ City/State/Zip: _________________________________________________________________________________ Please cut on dotted line. Hangar 9 Taylorcraft 26cc BNF... - Page 36 © 2011 Horizon Hobby, Inc. The Spektrum trademark is used with permission horizonhobby.com of Bachmann Industries, Inc. Hangar9.com All other marks are trademarks or registered trademarks of Horizon Hobby, Inc. Printed 02/2011 17996...
Need help?
Do you have a question about the Taylorcraft 26cc Hangar 9 and is the answer not in the manual?
Questions and answers