Service Manual LCD TV MODEL:LC26T1E/LC32T1E/LC37T1E/LC42T1E Amoi Notice: Please read this manual and the user’s manual before repairment. This manual is just for reference.
1、Preparation before maintenance 1.1、Master basic information. Adequate communication with customers is required, to learn how the trouble happens and what the status is. This will help to promote effect and efficiency of the service. Learn if the trouble has conflict with technical standards. 1.2、Reappearance of the trouble.
4.1.1、The block diagram of POWER (USE FOR LC32T1E/LC37T1E/LC42T1E) U1 ML4800 for +24V -12V LINE FILTER +12V +3.3V FS7M0880 +21V 5V_MUTE INPUT(90V~264V) FSD200...
Page 9
、 (USE FOR LC26T1E) +24V FS7M0880 -12V +12V LINE FILTER ML4800 +18V +3.3V S+5V FSD200 INPUT(90~264V)
Page 12
、 (USE FOR LC26T1E) J705: From I/O Board Audio Signal J706: From I/O Board SIF Signal TDA9875AH Sound Processor DDR-SDRAM Signal Control 128M Signal DDR-SDRAM 128M JF603: Panel Control Signal: BKLON and ANAPWM PW106B-10L LVDS Signal ImageProcessor Panel J704: From POWER Audio Board...
Page 13
、 (USE FOR LC26T1E) J13: From SCALER Board Update Control Main NJM4558M Control Current Audio Amplifier Signal TUNER Control Audio Signal Scart2 Signal Update Audio Output From TUNER Switch Interface Board Control NJM4558M SCART2 NJM4558M Audio Amplifier Amplifier CVBS Scart1 CVBS Signal Signal...
5、Work Principle The product mainly handles with video signal, such as RF (cable TV), CVBS(composite video), S-VIDEO(Y/C signal), YPbPr(progressive video), SCART, DTV signal, VGA and HDMI, as well as audio signal amplifying output. AV includes S-VIDEO and CVBS. In addition, it can input VGA and other signals to realize PIP function. Because the product is comprised of three boards, the work principle will separate into three parts as follows: 5.1、Work Principle of Power Board...
Page 15
current is limited, and the 380V voltage of PFC will descend. Actually, the current is limited when the peak value of this board is 0.7V. The pin 4 is a line voltage detecting pin. It detects the input AC Voltage, and when the 264V voltage becomes lower to about 80V, the amplifying ratio of the 4th pin is higher, and the duty cycle of the pin 12 of FPC is higher, the current to the PFC is higher.
Page 16
switch into LVDS signal to send it to PANEL for processing. 3、flow of main video signal process: CVBS composite video signal of TUNER (including TUNER signal) and S-VIDEO signal is output to PW106 of SCALER board via 2069 of IO board. PW106 handles with the input video signal, such as resolution and field switch, OSD overlapping, multi-window handling, to switch into PANEL-required resolution.
Page 17
check if the EAR-INT signal is abnormal, which is in order to avoid wasting time on checking amplifier. Regarding the connecting with IO board, it is important that I2C signal connects with MCU (MCU-INT、SCL-MCU、SDA-MCU). If there is any problem with the connecting, then the key and remote control work out.
Page 18
be realized by one video IC. c)Mini MCU module:remote and key signals receiving. The remote and key signal receiving is dependent, but the processing modes in MCU are the same. If the remote control and key both work out, then judge if the power supply and peripheral circuit of MCU is normal.
Page 47
R230=2.2K, R231=3.3K, C289=0.1uF R234=3.3K, R235=1.8K, C294=0.1uF R223=4.7K, R224=3.9K, C272=0.1uF if LM1117-ADJ is stuffed ; LM1117-ADJ is stuffed ; LM1086-ADJ is stuffed ; LM1117-ADJ is stuffed ; Confidential AMOI Title CORE POWER Size Document Number OPAL SINGLE CHANNEL Date: Friday, March 10, 2006...
Page 48
1000uF 10V AU PANEL POWER INPUT 22uH/5A_NC 4 HEADER C297 C298 22uH/5A 22uF 0.1uF J717 RCA_V_0 C291 C290 C330 C329 100uF 0.1uF 0.1uF_NS 0.1uF_NS Confidential AMOI Title MAIN POWER Size Document Number OPAL SINGLE CHANNEL Date: Friday, March 10, 2006 Sheet...
Page 54
6.3.Schematic Diagrams Public part for LC26T1E/LC32T1E/LC37T1E/LC42T1E...
Page 89
IC PI5V330Q 1. IN 5. S1 9. D 13. S2 2. S1 6. S2 10. S2 14. S1 3. S2 7. D 11. S1 15. EN 4. D 8. GND 12. D 16. VCC IC NJM4558 1. A OUTPUT 3. A+INPUT 5.
www.fairchildsemi.com ML4800 Power Factor Correction and PWM Controller Combo Features General Description • Internally synchronized leading-edge PFC and trailing- The ML4800 is a controller for power factor corrected, edge PWM in one IC switched mode power supplies. Power Factor Correction •...
Page 95
ML4800 PRODUCT SPECIFICATION Pin Configuration ML4800 16-Pin PDIP (P16) 16-Pin Narrow SOIC (S16N) IEAO VEAO I AC V FB I SENSE V REF V RMS V CC PFC OUT V DC PWM OUT RAMP 1 RAMP 2 DC I LIMIT TOP VIEW Pin Description Name...
Page 96
www.fairchildsemi.com FS7M0880 Fairchild Power Switch(FPS) Features Description • Precision Fixed Operating Frequency The Fairchild Power Switch(FPS) product family is specially • FS7M0880(66kHz) designed for an off line SMPS with minimal external • Pulse By Pulse Over Current Limiting components. The Fairchild Power Switch(FPS) consists of a •...
Page 97
www.fairchildsemi.com FSD20x-SERIES FSD200, FSD201 Fairchild Power Switch(FPS) Features Description • Single Chip 700V SenseFET Power Switch The FSD20x is specially designed for an off-line SMPS with • Precision Fixed Operating Frequency (134kHz) minimal external components. The FSD20x is a monolithic •...
Page 98
FSD20X-SERIES Absolute Maximum Ratings (Ta=25°C unless otherwise specified) Parameter Symbol Value Unit Maximum Drain Voltage D,MAX Maximum Vstr Pin Voltage str,max Continuous Drain Current (T =25°C) FSD200 Continuous Drain Current (T =25°C) FSD201 Maximum Supply Voltage CC,MAX Input Voltage Range −0.3 to V start −25 to +85...
8、 Software version view and Upgrade instruction Software version view Power on the TV normally, hold the “SOURCE” key for about 10s, then “Software version, Publish Date and MCU version” info. will display on the screen. Software upgrade method Ⅰ、Power off the power, you can find the software upgrade port beside the VGA port in the TV back cover (see picture 1).
Page 100
Picture 2. Upgrade cable Picture 3. COM port of the PC...
Page 101
Picture4. Connect the upgrade cable with COM port of the PC Ⅲ、Switch on the power and power on the TV after connecting with upgrade cable, you can begin to upgrade when the TV in the normal working status. Power-on method: Switch on the power, power on TV (the power indicator is red when the TV is in standby mode);...
Page 102
Picture5.The interface of upgrade tool Click “Choose” item in the upgrade tool and select the content which 1. includes upgrade software (in picture 7 and 8, assumed the upgrade file name is “appcode”), then select the upgrade file. Picture 6. Select the upgrade software(a)...
Page 103
Picture 7.Select upgrade software(b) Click “Flash” item in upgrade tool to begin upgrade, Do not cut off 2. the power or using “Cancel” during the upgrading. *Note:Remember to click “Flash” item firstly, then power on the power ( this solution limited), if it can upgrade, the following picture will display, the blue bar means the upgrading speed.
Page 104
software upgrade is finished. Picture 9. Software upgrade completed Ⅳ、Finally, close the upgrade application program, cut off the power and disconnect the upgrade cable. The TV software upgrade is finishen. Ⅴ、If the upgrade is failed: 1、Check whether the upgrade cable is connected well; 2、Check whether the selections of COM port are all right;...
11.1.Trouble shooting Symptoms Possible cause Remark ·Check if the power plug has been inserted properly No power into the socket. ·Check if the power switch has been turned on. ·Check if the power board could work normally. ·Refer to "Power Board Trouble shooting" ·Check if the wires are OK and connected correctly.
11.2. Power Board Power BOARD is NG Check whether the fuse is burn out Yes No Check whether the connection of DB1 and DB2 is ok, whether DS Power on and check whether there are 5VS, 5V and 24V pin of JM1, C33 and C27 is in short circuit state. Detailed operation Detailed operation Check the DB1 and DB2 with the help of multimeter...
Need help?
Do you have a question about the LC32T1E and is the answer not in the manual?
Questions and answers